Difference between revisions of "What can I do with IGEPv2"

From IGEP - ISEE Wiki

Jump to: navigation, search
m
 
(7 intermediate revisions by 3 users not shown)
Line 49: Line 49:
  
 
A detailed guide on how use GPIO-LEDS can be found by following this link: [[How to handle the gpio-LED]]
 
A detailed guide on how use GPIO-LEDS can be found by following this link: [[How to handle the gpio-LED]]
 +
 +
== Handle generic GPIO ==
 +
See [[How_to_use_GPIOs|GPIOs HOWTO]] to know details about that.
 +
Quick example could be:
 +
<pre>echo 156 > /sys/class/gpio/export
 +
echo out > /sys/class/gpio/gpio156/direction
 +
echo 0 > /sys/class/gpio/gpio156/value</pre>
 +
 +
<pre>echo 157 > /sys/class/gpio/export
 +
echo in > /sys/class/gpio/gpio157/direction
 +
cat /sys/class/gpio/gpio157/value</pre>
  
 
== How to use UART1 (RS232) ==
 
== How to use UART1 (RS232) ==
Line 82: Line 93:
  
 
Note that the board has been designed to use Line In for the audio input which means users need to add some type of pre-amp for a microphone to work or use a powered microphone. For a pre-amp for a microphone you can use MAX9812.
 
Note that the board has been designed to use Line In for the audio input which means users need to add some type of pre-amp for a microphone to work or use a powered microphone. For a pre-amp for a microphone you can use MAX9812.
 +
 +
Enable capture:
 +
 +
<pre>amixer -c 0 sset 'Analog Right AUXR' cap
 +
amixer -c 0 sset 'Analog Left AUXL' cap </pre>
  
 
You can record audio in with the application arecord, for example:
 
You can record audio in with the application arecord, for example:
  
$ arecord -t wav -c 2 -r 44100 -f S16_LE -v audio-in.wav
+
<pre>arecord -t wav -c 2 -r 44100 -f S16_LE -v audio-in.wav</pre>
  
 
Following output is expected on console:
 
Following output is expected on console:
Line 133: Line 149:
 
== How to use wifi ==
 
== How to use wifi ==
  
If you hve a wireless network adapter in your computer you can also connect to the board using the ad hoc network connection that the firmware configures byu default.
+
If you have a wireless network adapter in your computer you can also connect to the board using the ad hoc network connection that the firmware configures byu default.
  
Use your wireless manager to connect toi the wireless network called in the form
+
Use your wireless manager to connect to the wireless network called in the form
  
 
  IGEP_xx
 
  IGEP_xx
Line 147: Line 163:
 
== How to use bluetooth ==
 
== How to use bluetooth ==
  
A detailed guide on how use wifi can be found by following this link: [[How to setup Marvell bluetooth]]
+
A detailed guide on how use bluetooth can be found by following this link: [[How to setup Marvell bluetooth]]
  
 
== How to use the SD card ==
 
== How to use the SD card ==

Latest revision as of 12:36, 11 May 2016


Overview

This is the 2/3 chapter of the Getting Started with IGEPv2 Tutorial Guide.

In this second chapter, we will learn some basics tasks. Upon completion, you will be ready to continue with chapter 3/3 that explains more advanced tasks.



What can I do

You must logged in the board.

How to use serial console

Connect a serial (COM port) cable (known as the AT/Everex Cable) to the 10-pin header J960 on the board. Now you need a Null-Modem DB9 male-make serial cable. Connect the cable between the board and your PC. Open the serial on your PC using your preferred serial communications program (minicom) and configure the port as follows:

  • 115200
  • 8N1
  • no flow control (either software or hardware)

Open the serial port and the debug shell prompt should appear.

A detailed guide on how to connect via serial debug port can be found by following this link: Using serial debug port to communicate

Handle the GPIO-LEDS

The board has two user bicolor (green/red) leds available that can be controlled. In its simplest form, you can control of LEDs from userspace. LEDs appear in /sys/class/leds/ and you can turn on and off with following commands:

$ echo 0 > /sys/class/leds/d240\:green/brightness
$ echo 1 > /sys/class/leds/d240\:red/brightness
$ echo 0 > /sys/class/leds/d240\:red/brightness
$ echo 1 > /sys/class/leds/d440\:green/brightness
$ echo 1 > /sys/class/leds/d440\:red/brightness

A detailed guide on how use GPIO-LEDS can be found by following this link: How to handle the gpio-LED

Handle generic GPIO

See GPIOs HOWTO to know details about that. Quick example could be:

echo 156 > /sys/class/gpio/export 
echo out > /sys/class/gpio/gpio156/direction
echo 0 > /sys/class/gpio/gpio156/value
echo 157 > /sys/class/gpio/export 
echo in > /sys/class/gpio/gpio157/direction
cat /sys/class/gpio/gpio157/value

How to use UART1 (RS232)

The board has another UART available on J960 connector (UART1). This UART is shared with RS485 so it's incompatible use both interfaces at the same time. For that reason to use UART1 for RS232 comunications you should disable RS485 interface. You can do this adding following kernel cmdline parameter

board.ei485=no

Now, you can connect the serial AT/Everex Cable to the 10-pin header J960 on the board. In that case the first pin of the AT/Everex Cable (red) should be connected to the pin number 10 of the header J960. You also need a Null-Modem DB9 male-make serial cable. Connect the cable between the target board and your PC.

Open the serial port on your PC using your preferred serial communications program (minicom) and configure the port as follows:

  • 115200
  • 8N1
  • no flow control (either software or hardware)

On the target board open a serial port as follows:

 $ microcom -s 115200 /dev/ttyS0

Now when you write a character in you PC serial port, the character should appear in the target board.

A detailed guide on how use UARTS can be found by following this link: How to use UARTs

How to use RS-485

This How-To is meant to be a starting point for people to learn to use RS-485 port on IGEP devices as quickly and easily as possible. We use IGEP YOCTO Firmware and RS485 example which describe how to setup and write data on the RS-485 port.

A detailed guide on how use UARTS can be found by following this link: How to use RS485

Get sound in (audio in)

External Audio input devices, such as a powered microphone or the audio output of a PC or MP3 player, can be connected to the via a 3.5mm jack (Audio IN).

Note that the board has been designed to use Line In for the audio input which means users need to add some type of pre-amp for a microphone to work or use a powered microphone. For a pre-amp for a microphone you can use MAX9812.

Enable capture:

amixer -c 0 sset 'Analog Right AUXR' cap
amixer -c 0 sset 'Analog Left AUXL' cap 

You can record audio in with the application arecord, for example:

arecord -t wav -c 2 -r 44100 -f S16_LE -v audio-in.wav

Following output is expected on console:

Recording WAVE 'audio-in.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
Plug PCM: Hardware PCM card 0 'TWL4030' device 0 subdevice 0
Its setup is:
stream       : CAPTURE
access       : RW_INTERLEAVED
format       : S16_LE
subformat    : STD
channels     : 2
rate         : 44100
exact rate   : 44100 (44100/1)
msbits       : 16
buffer_size  : 32768
period_size  : 2048
period_time  : 46439
tick_time    : 7812
tstamp_mode  : NONE
period_step  : 1
sleep_min    : 0
avail_min    : 2048
xfer_align   : 2048
start_threshold  : 1
stop_threshold   : 32768
silence_threshold: 0
silence_size : 0
boundary     : 1073741824

When ever you think you want to stop recording just press CTRL+C

Get sound out (audio out)

Connect an external output audio device to the 3.5mm jack Audio Out connector in the board, such as external stereo powered speakers.

The amplifiers for the headset output are disabled by default, so the first thing you'll do is enable these amplifiers with:

$ amixer set -D hw:0 'Headset' 0dB
$ amixer set -D hw:0 'HeadsetL Mixer AudioL2' on
$ amixer set -D hw:0 'HeadsetR Mixer AudioR2' on

Then you can easily play a *.wav sound with the application Aplay, for example:

$ aplay audio-in.wav

How to use wifi

If you have a wireless network adapter in your computer you can also connect to the board using the ad hoc network connection that the firmware configures byu default.

Use your wireless manager to connect to the wireless network called in the form

IGEP_xx

After connecting, a DHCP IP address should be adquired. Now you can access, for example with ssh, to the target board connecting to the 192.168.7.1 address.

$ ssh root@192.168.6.1

A detailed guide on how use wifi can be found by following this link: Using IGEP WLAN to communicate

How to use bluetooth

A detailed guide on how use bluetooth can be found by following this link: How to setup Marvell bluetooth

How to use the SD card

You can connect a micro SD card for storage. After plugin the SD card the kernel should detect the card and automount in /media directory.

How to use the USB OTG

In order to act in host mode and add some peripherals like keyboard, mouse or pendrives you require a special cable that grounds the ID pin. Since the OTG port only provides 100mA of power a USB hub is recommended.

Though a common USB Standard-A to Mini-B type cable the port acts as a device. In this mode you can connect to the board using the USB Ethernet Gadget. Use this cable between your computer and the target board and connect with:

$ ssh root@192.168.7.1

A detailed guide on how use wifi can be found by following this link: Using USB ethernet gadget to communicate



You have successfully completed this chapter of the guide.


Continue this tutorial guide: 3/3 - Start developing under IGEP Technology
Igep forum.png If you have any question, don't ask to ask at the IGEP Community Forum or the IGEP Community Chat Irc.png