Difference between revisions of "How to setup the IDC10 cable"
From IGEP - ISEE Wiki
Manel Caro (talk | contribs) (How to Prepare the IDC10 to DB9 Cable for use it with a USB232 Serial Conversor on IGEPv2-RC Series) |
Manel Caro (talk | contribs) |
||
| Line 1: | Line 1: | ||
| − | = How to Prepare the IDC10 to DB9 Cable for use it with a USB232 Serial Conversor on IGEPv2-RC Series = | + | = How to Prepare the IDC10 to DB9 Cable for use it with a USB232 Serial Conversor on IGEPv2-RC Series = |
== Necessary Material == | == Necessary Material == | ||
| − | # | + | #IDC10 to DB9 Cable. |
| − | IDC10 to DB9 Cable. | + | #Cutter. |
| + | #Scissors.<br> | ||
| − | + | [[Image:DSC 0164.JPG]] | |
| − | |||
| − | + | <br> | |
| − | |||
| + | == Procedure == | ||
| + | The first step it's to separate the wires 5 and 6 for it and start from the read mark (the red mark it's the first) you should count 5 wires the you should do a cut between wires 5 and 6. | ||
| − | + | <br> | |
| + | [[Image:DSC 0168.JPG]] | ||
| + | <br> | ||
| − | + | This is the result for the cut between wire 5 and 6. | |
| − | + | <br> | |
| − | + | [[Image:DSC 0169.JPG]] | |
| − | + | <br> | |
| + | Now you must cut the unnecessary wires (wires 6 to 10). | ||
| + | [[Image:DSC 0172.JPG]]<br> | ||
| − | + | <br> | |
| + | And the final result. | ||
| + | <br> | ||
| − | [[Image: | + | [[Image:DSC 0176.JPG]] |
| + | <br> | ||
| + | Now you're ready for test the result: | ||
| − | + | <br> | |
| − | [[Image: | + | [[Image:DSC 0177.JPG]] |
| + | <br> | ||
| − | + | == Serial Port Setup == | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | == Serial Port Setup == | ||
You can use minicom, putty or a lot of programs for connect to the serial debug port. The right Serial Port Configuration it's: 115200 - 8N1 without hardware or software flow control. | You can use minicom, putty or a lot of programs for connect to the serial debug port. The right Serial Port Configuration it's: 115200 - 8N1 without hardware or software flow control. | ||
Revision as of 19:02, 12 November 2010
Contents
How to Prepare the IDC10 to DB9 Cable for use it with a USB232 Serial Conversor on IGEPv2-RC Series
Necessary Material
- IDC10 to DB9 Cable.
- Cutter.
- Scissors.
Procedure
The first step it's to separate the wires 5 and 6 for it and start from the read mark (the red mark it's the first) you should count 5 wires the you should do a cut between wires 5 and 6.
This is the result for the cut between wire 5 and 6.
Now you must cut the unnecessary wires (wires 6 to 10).
And the final result.
Now you're ready for test the result:
Serial Port Setup
You can use minicom, putty or a lot of programs for connect to the serial debug port. The right Serial Port Configuration it's: 115200 - 8N1 without hardware or software flow control.
