User:Pau pajuelo

TODO:

Update peripheral tutorials, finish gpio example program

Categorize new tutorials

Finish tutorials below

Upgrade IGEP Technology Devices Guides

Link all development tools documentation when possible (do a diagram)

How to manage the kernel modules on Linux

How do I edit my kernel command line

Basic Software instructions

Getting started with IGEP PARIS

IGEP PARIS Tutorial Guides

1/3 - Getting started with IGEP PARIS 2/3 - What can I do with IGEP PARIS 3/3 - Start developing with IGEP PARIS IGEP PARIS Product Page IGEP PARIS Hardware manual

Overview

This is the 1/3 chapter of IGEP PARIS Expansion Tutorial Guide.

In this first chapter, we will learn how to connect some expansion peripherals.

Requirements

In these tutorials we are going to need the following components:

• IGEP COM PROTON or IGEP COM MODULE.
• 5V DC power supply with a minimum of 3A current capacity.
• Seiko 7" screen if you need a touch screen.
• DB9 connector and USB serial converter to follow serial communication tutorial.
• Ethernet cable for network communications.
• An USB keyboard and a mouse (optional).
• Li-on battery with 3V3 (optional).
• A PC.

Getting started

TFT and Touchscreen

200px

IGEP PARIS Expansion supports SEIKO 7” LCD screen. Use J200, J203 and J204 connectors to attach screen. See image for more details.

Know more

IGEP PARIS Expansion integrates LCD backlight driver (TPS61081) and touch screen controller (TSC2046), a 4-wire touch screen controller which supports a low voltage I/O interface from 1.5V to 5.25V.

Serial port

Basic

IGEP PARIS Expansion integrates a DB9 RS232 connector.

Know more

This peripheral (UART 3) can be used to debug system using kernel traces, getting a remote prompt, etc.

Ethernet Network cable

Basic

Plug an Ethernet cable between IGEP PARIS and your client machine (or any other network device with Ethernet connectivity).

Know more

IGEP PARIS comes with one 10/100BASE-TX Ethernet port.

In the following chapters we will use Ethernet to access IGEP PARIS.

USB devices

Basic

Connect a USB hub to the USB type-A connector (USB Host) in IGEP PARIS.

Then plug a USB keyboard and USB mouse to the USB hub.

Know more

Only USB 2.0 devices will work in IGEP PARIS, so if you connect any USB mouse 1.0 into the USB host connector without using a USB hub 2.0, it will not work.

Battery

J102 is a 2.5mm pitch, can be used to connect a 3,7V Battery to power the base board.

Connect IGEP PARIS Expansion with IGEP COM MODULE/NEUTRON Board

The IGEP PARIS Expansion connects to the IGEP COM MODULE/NEUTRON Board through J1 and J4 connectors. Just take a look on the figure to mount it:

Connect IGEP PARIS Expansion with IGEP COM PROTON Board

The IGEP PARIS Expansion connects to the IGEP COM PROTON Board through J1, J4 and J8 connectors. Just take a look on the figure to mount it:

Power up IGEP PARIS Expansion

Once you have connected the peripherals you can apply power to your IGEP PARIS with 5V DC power supply (J101) with a minimum of 3A current capacity.

Test Demo software distribution with touch screen

Basic

When IGEP PARIS powers up, the desktop of the preinstalled software will appear on the touch screen.

You can use your fingers or a mouse and a keyboard to test the demo applications.

Screenshot of the Desktop of the pre-installed software

Know more

All IGEP Processor Boards have a pre-installed software in its flash memory which consists of a minimal Linux-based distribution with a lite X Window System and GNOME Mobile based applications created with Poky Platform Builder.

Log into IGEP PARIS Expansion via Ethernet interface

	In non-Linux operating system, use IGEP SDK Virtual Machine to connect to IGEP COM MODULE via USB or read article "Using USB ethernet gadget to communicate"

In your Host Machine:

Open a Terminal session and set the IP of the Ethernet interface in which IGEP is connected (for example eth0):

• In the file /etc/network/interfaces, you should add:

iface eth0 inet dhcp 
iface eth0:0 inet static
address 192.168.5.10
netmask 255.255.255.0

• Type in a terminal:

sudo ifup eth0:0

• Revise that:

jdoe@ubuntu ~ $ ifconfig
...
eth0:0    Link encap:Ethernet  HWaddr 08:00:27:ad:0c:ad  
          inet addr:192.168.5.10  Bcast:0.0.0.0  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
...

• Connect to IGEP device

jdoe@ubuntu ~ $ ssh root@192.168.5.1

---

You have successfully completed this chapter of the guide.

Continue this tutorial guide: [[What can I do with IGEP PARIS|2/3 - What can I do with IGEP PARIS]]

If you have any question, don't ask to ask at the IGEP Community Forum or the IGEP Community Chat

IGEP PARIS Tutorial Guides

1/3 - Getting started with IGEP PARIS 2/3 - What can I do with IGEP PARIS 3/3 - Start developing with IGEP PARIS IGEP PARIS Product Page IGEP PARIS Hardware manual

Getting started with IGEP BERLIN

IGEP BERLIN Tutorial Guides

1/3 - Getting started with IGEP BERLIN 2/3 - What can I do with IGEP BERLIN 3/3 - Start developing with IGEP BERLIN IGEP BERLIN Product Page IGEP BERLIN Hardware manual

Overview

This is the 1/3 chapter of IGEP BERLIN Expansion Tutorial Guide.

In this first chapter, we will learn how to connect some expansion peripherals.

Requirements

In these tutorials we are going to need the following components:

• IGEP COM PROTON or IGEP COM MODULE
• 5V DC power supply with a minimum of 3A current capacity.
• Seiko 7" screen if you need a touch screen.
• DB9 connector and USB serial converter to follow serial communication tutorial.
• Ethernet cable.
• A monitor compatible with DVI-D
• An USB keyboard and a mouse
• 4 pin connector for CAN Bus with another IGEP Board with CAN peripheral to follow CAN Bus communication tutorial.
• SIM card with an antenna to follow Telit modem tutorial.
• Composite video cable, composite video output peripheral (PAL or NTSC) and a screen to follow TVP5151 tutorial.
• Li-on battery with 3V3
• A PC

Getting started

TFT and Touchscreen

200px

IGEP BERLIN Expansion supports SEIKO 7” LCD screen. Use J200, J203 and J204 connector for SEIKO 7". See image for more details.

Know more

IGEP BERLIN Expansion integrates LCD backlight driver (TPS61081) and touch screen controller (TSC2046), a 4-wire touch screen controller which supports a low voltage I/O interface from 1.5V to 5.25V.

Serial port

Basic

IGEP BERLIN Expansion integrates a DB9 RS232 connector. Plug a DB9 cable.

Know more

This peripheral (UART 3) can be used to debug system using kernel traces, getting a remote prompt, etc.

Ethernet Network cable

Basic

Plug an Ethernet cable between IGEP PARIS and your client machine (or any other network device with ethernet connectivity).

Know more

IGEP PARIS comes with one 10/100BASE-TX Ethernet ports.

In the following chapters we will use ethernet to access IGEP PARIS.

USB devices

Basic

Plug an USB keyboard and USB mouse to the USB ports.

Know more

Only USB 2.0 devices will work in IGEP PARIS, so if you connect any USB mouse 1.0 into the USB host connector without using a USB hub 2.0, it will not work.

Composite Video Decoder

Basic

IGEP BERLIN Expansion integrates two composite video connectors to decode analog input signal. Plug some peripheral with video composite output.

Know more

Analog input is decoded by TVP5151.

GSM/GPRS modem

Basic

GSM-GPRS antenna (highly recommended)	SIM card reader

IGEPv2 Expansion integrates a GSM/GPRS modem to make phone calls or to send SMS or to write and read data from it, etc.

Know more

Modem chip Telit GE865 is a small GSM/GPRS Ball-Grid-Array BGA module with next main features:

• Quad-band EGSM 850 / 900 / 1800 / 1900 MHz
• Power consumption (typical values)

    - Power off: ‹ 62 uA
    - Idle (registered, power saving): 1.6 mA @ DRX=9

CAN bus

Basic

IGEPv2 Expansion integrates a CAN peripheral. Connect any CAN bus device or network to the CAN bus connector (J703).

Know more

This output is controled by MICROCHIP MCP2515. J703 is a 3.5 mm pitch terminal blocks 4 Positions:

Signal Name	Pin #	Description
VDD_CAN	J703:1	Supply Voltage (+5V DC)
CANL	J703:2	CAN Low-Level Voltage I/O
GND	J703:3	Ground
CANH	J703:4	CAN High-Level Voltage I/O

DVI monitor

Basic

IGEPv2 has a HDMI connector with a DVI-D interface

Connect IGEPv2 to a DVI-D compatible monitor.

Know more

The Digital Visual Interface (DVI) is a video standard interface designed to provide very high visual quality on digital display devices such as flat panel LCD computer displays and digital projectors. It is partially compatible with the High-Definition Multimedia Interface (HDMI) standard in digital mode (DVI-D), and VGA in analog mode (DVI-A).

Note that your monitor should be able to support 1024 x 768 @ 60 Hz, which is the default resolution in the preinstalled software.

VGA monitor

Basic

IGEPv2 Expansion integrates a VGA connector, the output VGA signal is equal to HDMI connector. Plug a monitor with VGA input.

Know more

This output is controled by ADV7125KSTZ140 Integrated Circuit.

Battery

J102 is a 2.5mm pitch, can be used to connect a 3,7V Battery to power the base board.

Connect IGEP BERLIN Expansion with IGEP COM MODULE/NEUTRON Board

The IGEP BERLIN Expansion connects to the IGEP COM MODULE/NEUTRON Board through J1 and J4 connectors. Just take a look on the figure below to mount it:

Connect IGEP BERLIN Expansion with IGEP COM PROTON Board

The IGEP BERLIN Expansion connects to the IGEP COM PROTON Board through J1, J4, J9 and J8 connectors. Just take a look on the figure below to mount it:

Power up IGEP BERLIN Expansion

Once you have connected the peripherals you can apply power to your IGEP BERLIN with 5V DC power supply (J101) with a minimum of 3A current capacity.

Test the Demo software distribution with touch screen

Basic

When IGEP BERLIN powers up, the desktop of the preinstalled software will appear on the touch screen.

You can use your fingers to test the demo applications.

Screenshot of the Desktop of the pre-installed software

Know more

All IGEP Processor Boards have a pre-installed software in its flash memory which consists of a minimal Linux-based distribution with a lite X Window System and GNOME Mobile based applications created with Poky Platform Builder.

Log into IGEP BERLIN Expansion via Ethernet interface

	In non-Linux operating system, use IGEP SDK Virtual Machine to connect to IGEP COM MODULE via USB or read article "Using USB ethernet gadget to communicate"

In your Host Machine:

Open a Terminal session and set the IP of the Ethernet interface in which IGEP is connected (for example eth0):

• In the file /etc/network/interfaces, you should add:

iface eth0 inet dhcp 
iface eth0:0 inet static
address 192.168.5.10
netmask 255.255.255.0

• Type in a terminal:

sudo ifup eth0:0

• Revise that:

jdoe@ubuntu ~ $ ifconfig
...
eth0:0    Link encap:Ethernet  HWaddr 08:00:27:ad:0c:ad  
          inet addr:192.168.5.10  Bcast:0.0.0.0  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
...

• Connect to IGEP device

jdoe@ubuntu ~ $ ssh root@192.168.5.1

---

You have successfully completed this chapter of the guide.

Continue this tutorial guide: [[What can I do with IGEP BERLIN|2/3 - What can I do with IGEP BERLIN]]

If you have any question, don't ask to ask at the IGEP Community Forum or the IGEP Community Chat

IGEP BERLIN Tutorial Guides

1/3 - Getting started with IGEP BERLIN 2/3 - What can I do with IGEP BERLIN 3/3 - Start developing with IGEP BERLIN IGEP BERLIN Product Page IGEP BERLIN Hardware manual

[IGEP Technology devices features table proposal]

	IGEP0032	IGEP0030	IGEP0030	IGEP0020	IGEP0010
Product name	IGEP COM PROTON	IGEP COM MODULE	IGEP COM ELECTRON	IGEPv2	IGEP0010
Devices and interfaces					(discontinued product)
ARM CPU	DM3730 1GHz	DM3730 1GHz	AM3703 1GHz	DM3730 1GHz	-
DSP	TMS320DM-C64+ 800 Mhz	TMS320DM-C64+ 800 Mhz	-	TMS320DM-C64+ 800 Mhz	-
RAM Memory	512 MBytes / 200 Mhz	512 MBytes / 200 Mhz	256 MBytes / 200 Mhz	512 MBytes / 200 Mhz	-
Flash Memory	512 MBytes	512 MBytes	512 MBytes	512 MBytes	-
MicroSD Card Reader	x 1	x 1	x 1	x 1	-
USB 2.0 Host	-	-	-	x 1	-
USB 2.0 OTG	x 1	x 1	x 1	x 1	-
RS232	-	-	-	x 1	-
RS485	-	-	-	x 1	-
JTAG	x 1	-	-	x 1	-
Stereo audio In/Out	-	-	-	x 1	-
DVI on HDMI	-	-	-	x 1	-
Ethernet	-	-	-	x 1	-
Wifi	-	x 1	-	x 1	-
Bluetooth	-	x 1	-	x 1	-
EEPROM	x 1	-	-	-	-
S-Video	-	-	-	T.P.	-
Camera Interface	-	x 1	-	N.P.	-
Analog to digital converter	-	-	-	N.P.	-
Keyboard matrix	-	-	-	N.P.	-
LEDs	x 3 green LEDs	x 2 bicolor LEDs	x 1 bicolor LED	x 2 bicolor LEDs	-
TFT Interface	-	-	-	x 2	-
RTC Battery Back Up	-	-	-	x 2	-
Size	35x51,2mm	18x68,5mm	18x68,5mm	65x95mm	-
Expansion connectors	Power and many functionalities from OMAP3 processor	Power and many functionalities from OMAP3 processor	Power and many functionalities from OMAP3 processor	Power 5V and 1.8V, UART, McBSP, McSPI, I2C, GPIO, RS485 with transceiver, Keyboard	-
Main pages					-
Getting started guide
Hardware manual					-

• O: Available on board

• N.P.: Not populated THESE DEVICES and/or CONNECTORS ARE AVAILABLE, BUT NOT POPULATED BY DEFAULT

• T.P.: Test points

igep.ini parameters

The kernel command line syntax is name=value1. These next parameters are supported in igep.ini since IGEP-X_Loader 2.4.0-2:

[kernel]

Parameter Name	Description	Default value	Comments
kaddress	Kernel copy address	=0x80008000	Hex memory address
rdaddress	Ram Disk location address	=0x81600000	Hex memory address; disabled by default
serial.low	Serial number (low part)	=00000001	Numeric
serial.high	Serial number (high part)	=00000000	Numeric
revision	Revision ID	=0003	Numeric
kImageName	Kernel, binary image name	=zImage	Kernel or binary image name
kRdImageName	Kernel RAM Disk Image Name	-	Ram Disk image name
MachineID	Machine ID (kernel ID)	;IGEPv2 =2344	;Module =2717 ;Proton =3203
Mode	Boot Mode	;Linux kernel =kernel	;Other image (like uboot) [binary image]

[kparams]

Parameter Name	Description	Default value	Comments
buddy	Enable/disable expansion board support	;IGEPv2 Expansion Board support =igep0022	;Berlin and Paris Expansion Board support =base0010 New York Expansion =ilms0015
console	Setup the kernel console parameters	=ttyO2,115200n8	-
earlyprintk	Enable early printk	-	-
mem	Setup the Board Memory Configuration	=430M	-
boot_delay	Setup the boot delay	=0	-
mpurate	Setup ARM Processor Speed	-	-
loglevel	Setup the loglevel	-	-
debug	Enable kernel debug output	-	-
fixrtc	Fix RTC variable	-	-
nocompcache	Configure nocompcache variable	=1	-
omapfb.mode	Configure frame bugger configuration	=dvi:hd720-16@50	;Other configuration =dvi:1280x720MR-16@60
vram	Configure Video RAM assigned to every frame buffer	-	-
omapfb.vram	Configure Video RAM assigned to every frame buffer	-	-
omapfb.debug	Configure frame buffer debug output	-	-
omapdss.debug	Configure DSS Video debug output	-	-
smsc911x.mac0	Configure Board Ethernet Mac Address	=0xb2,0xb0,0x14,0xb5,0xcd,0xde	For IGEP BERLIN
smsc911x.mac1	Configure Board Ethernet Mac Address	=0xb2,0xb0,0x14,0xb5,0xcd,0xdf	For IGEP BERLIN (only with IGEP PROTON)
smsc911x.mac	Configure Board Ethernet Mac Address	=0xb2,0xb0,0x14,0xb5,0xcd,0xde	For IGEPv2, IGEP PROTON, IGEP PARIS and IGEP BERLIN
ubi.mtd	Fot UBI FS boot	-	-
root	Configure root directory for MMC, NFS or UBI	;For mmc memory =/dev/mmcblk0p2 rw rootwait	;For flash memory =/dev/mtdblock2
nfsroot	For NFS boot	-	-
rootfstype	For UBI FS boot	-	-
ip	For NFS boot	-	-
init	Assign init program	-	-
musb_hdrc.debug	USB debug	-	-
musb_hdrc.use_dma	USB over network	-	-
libertas.libertas_debug	Configure libertas debug	-	-
board.ei485	Enable/disable RS485	;Enable RS485 =yes	;Disable RS485 =no
board.modem	Enable/disable GPRS modem	;Enable modem (IGEPv2 Expansion) =no	;Enable modem (IGEPv2 Expansion) =yes
buddy.revision	Enable hardware buddy revision [A or B]	Only for base0010 =A	Only for base0010 =B

How to use GPIOs (update it)

Overview

This How-To is meant to be a starting point for people to learn use GPIOs for IGEP v2 devices as quickly and easily as possible. For this how-to i used Linaro Headless with Kernel 2.6.35.y, Ubuntu 10.04 with Linaro Toolchain, IGEP v2 RC5 and GPIO driver.

There are more ways to use GPIOs in IGEP v2, but this one is very simple.

Feedback and Contributing

At any point, if you see a mistake you can contribute to this How-To.

Compile GPIO driver source code via Host

Download GPIO driver and Kernel 2.6.35.y source code. Extract files.

Edit GPIO driver Makefile's:

-In files: $/app/Makefile and $/lib/Makefile, make sure that your CROSS_COMPILE path is correct.

-In file: $/modules/Makefile, make sure that your CROSS_COMPILE path is correct and type your Kernel 2.6.35.y path.

We will use the ncurses program for set up Kernel configuration, if you don't have this program installed then you must install it with this command:

sudo apt-get install ncurses-dev 

-Go to kernel path and type:

make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- igep00x0_defconfig

Exit Linux Kernel Configuration an return to Bash. Type:

make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- modules_prepare

File $/include/generated/autoconf.h was created

Finally compile GPIO driver, go to main Makefile path and compile all source code using make command.

Send binaries created from Host to Igep v2.

Install binaries via IGEP

Log with root user to install binaries.

Install module

Go to:$/modules and insert user-gpio-drv.ko into linux kernel with the following command:

insmod user-gpio-drv.ko

Check that user-gpio-drv.ko is currently loaded with the following command:

lsmod

The result will be similar at that:

root@localhost:~/gpio-driver/module# lsmod
Module                  Size  Used by
user_gpio_drv           1639  0 
omap_wdt                3411  0 
spidev                  4198  0 
iommu                   8558  0 
rtc_twl                 4411  0 
rtc_core               11187  1 rtc_twl
twl4030_keypad          2970  0 

The module is loaded until system halt.

Install shared library

Go to:$/lib. libgpio.so is here.

If a program is linked with shared libraries, Kernel seek in specific paths when program is executed. Now is necessary link the libgpio.so path to the environment variable LD_LIBRARY_PATH, use the following command:

export LD_LIBRARY_PATH=/root/gpio-driver/lib/

Check that libgpio.so is linked correctly. Go to:$/gpio-driver/app, gpio program is here. Type next command:

ldd gpio 

ldd command, print shared library dependencies. The result will be similar at that:

root@localhost:~/gpio-driver/app# ldd gpio
	libgpio.so => /root/gpio-driver/lib/libgpio.so (0x40197000)
	libc.so.6 => /lib/libc.so.6 (0x401a0000)
	/lib/ld-linux.so.3 (0x4008a000)

The shared library is linked until system halt. Now you can execute gpio example program.

Testing driver

To make sure than driver works well, make the next test. I used GPIO_136(sdmmc2_dat4) and GPIO_137(sdmmc2_dat5) because IGEP v2 RC5(without WIFI) don't use them by default:

NOTE: For more information visit this page (under construction).

Configure Mux

Go to:/sys/kernel/debug/omap_mux, and change this mux configuration:

echo 0x104>sdmmc2_dat4
echo 0x104>sdmmc2_dat5

Use cat command to check it:

cat sdmmc2_dat4
cat sdmmc2_dat5

The result will be similar at that:

root@localhost:/sys/kernel/debug/omap_mux# cat sdmmc2_dat4
name: sdmmc2_dat4.gpio_136 (0x48002164/0x134 = 0x0104), b ae4, t NA
mode: OMAP_PIN_INPUT | OMAP_MUX_MODE4
signals: sdmmc2_dat4 | sdmmc2_dir_dat0 | NA | sdmmc3_dat0 | gpio_136 | NA | NA | safe_mode

and

root@localhost:/sys/kernel/debug/omap_mux# cat sdmmc2_dat5
name: sdmmc2_dat5.gpio_137 (0x48002166/0x136 = 0x0104), b ah3, t NA
mode: OMAP_PIN_INPUT | OMAP_MUX_MODE4
signals: sdmmc2_dat5 | sdmmc2_dir_dat1 | cam_global_reset | sdmmc3_dat1 | gpio_137 | hsusb3_tll_stp | mm3_rxdp | safe_mode

Note: OMAP_PIN_INPUT=Input/Output pin and OMAP_PIN_OUTPUT=Output pin, for Read/Write test you need the first one. GPIO is configured in mode 4.

Read/Write test

Link GPIO_136 and GPIO_137 with a wire, these pins are located in J990 connector with numbers 7 and 9. I use the next connector to join them:

Now type next code:

root@localhost:~/gpio-driver/app# ./gpio input 136
root@localhost:~/gpio-driver/app# ./gpio output 137 0
root@localhost:~/gpio-driver/app# ./gpio get 136     
0
root@localhost:~/gpio-driver/app# ./gpio output 137 1
root@localhost:~/gpio-driver/app# ./gpio get 136     
1
root@localhost:~/gpio-driver/app# 

The results (CMOS Voltages: 0V-1V8):

The code above shows that driver works properly, GPIO_136 is configured like input and GPIO_137 is configured like output with value 0, when read GPIO_136 the result is 0. To make sure that works well, configure GPIO_137 with value 1, now GPIO_136 reads 1.
This driver have more options like IRQ, but is not explained here.