Difference between revisions of "IGEPv2"
From IGEP - ISEE Wiki
(→Software) |
|||
| Line 149: | Line 149: | ||
* [http://labs.isee.biz/index.php/IGEP_Firmware_set-up#Install_IGEP_Firmware_on_bootable_SD-card Official IGEP Firmware] | * [http://labs.isee.biz/index.php/IGEP_Firmware_set-up#Install_IGEP_Firmware_on_bootable_SD-card Official IGEP Firmware] | ||
| − | ===Custom=== | + | ===Custom Software=== |
* [http://downloads.isee.biz/pub/relaunch/rootfs/ubuntu/xenial/ubuntu-xenial-armhf-igep-base-v0.01.tgz Ubuntu Xenial 16.04 LTS ARM Hard Float] | * [http://downloads.isee.biz/pub/relaunch/rootfs/ubuntu/xenial/ubuntu-xenial-armhf-igep-base-v0.01.tgz Ubuntu Xenial 16.04 LTS ARM Hard Float] | ||
* [http://downloads.isee.biz/pub/relaunch/rootfs/debian/stretch/debian-stretch-armhf-igep-base-v0.01.tgz Debian Stretch 9 ARM Hard Float] | * [http://downloads.isee.biz/pub/relaunch/rootfs/debian/stretch/debian-stretch-armhf-igep-base-v0.01.tgz Debian Stretch 9 ARM Hard Float] | ||
Revision as of 10:21, 25 September 2018
Contents
Industrial Processor board SINGLE core ARM Cortex-A8 + DSP C64P up to 1000 MHz
IGEPv2 is an industrial processor board. It unleashes laptop-like performance and expandability without the bulk, expense or noise of typical desktop machines and is the perfect solution for many industrial applications or system requirements.
Features | |
|---|---|
| Processor |
DM3730, by Texas Instruments |
|
3D/2D Accelerator |
PowerVR SGX GPU, providing 2D/3D graphics acceleration with OpenGL ES1.0, OpenGL ES2.0 and Open VG support |
|
Video |
Video acceleration: H.264, H.263, MPEG-4, MPEG-2, JPEG, WMV9 and additional codecs. Video encoder/decoder up to 720p. |
|
Memory |
RAM: Up to 512 MB Mobile DDR (Standard setup 512 MB) Flash: Up to 512 MB (Standard setup 512 MB) Onboard micro-SD card socket |
|
Ethernet |
10/100 Mbps Ethernet PHY Interface |
|
USB |
1 x USB 2.0 Host |
|
Display |
1 x DVI-D/HDMI |
|
Image Capture Interface |
1 x CPI interface (12 bits) |
|
Wireless |
WiFi IEEE 802.11 b/g/n (Access Point: Yes) |
|
Antenna |
1 x Internal WiFi/Bluetooth antenna |
| Additional Interfaces
(Other combinations available, see Hardware Manual for more information) |
2 x I2C |
|
SW Support |
Linux Android |
|
Power Supply |
Power from expansion connectors: 5 V Power from JST connector: 5 V Power from jack power: 5 V |
|
Power Consumption |
Typical 2,2 W (depending on software) Maximum 2,8 W (depending on software) |
|
Thermal |
Industrial temperature: -40 ºC to +85 ºC |
|
Form Factor |
65 mm x 95 mm |
|
Humidity |
93% relative Humidity at 40 ºC, non-condensing (according to IEC 60068-2-78) |
|
MTBF |
> 100000 hours |
Versions
| Model | Description |
|---|---|
| IGEPv2 - RA | Internal use, OMAP3530 processor (2008) |
| IGEPv2 - RB | Initial IGEPv2 with OMAP3530 720Mhz (2009) and Marvell WIFI b/g & BT |
| IGEPv2 - RC | Compatible OMAP3530 and DM3730 (2011) |
| IGEPv2 - RD | N/A (Internal use) |
| IGEPv2 - RE | N/A (Internal use) |
| IGEPv2 - RF | DM3730 with new WILINK 8 module |
Documentation
- IGEPv2 SoC: DM3730
- Datasheet
- Schematic (RC | RF )
- Mechanicals
- Software Manual
- Hardware Manual ( RC | RF )
Tutorials
- IGEPv2 Boot Pin-out
- How to prepare a ready to boot firmware
- U-Boot Bootloader
- Linux Kernel
- IGEP Firmware set-up
- Boot from MicroSD Card
- Boot from NAND/eMMC flash.
- Update Installed IGEP Firmware
Firmware
Official
Custom Software
- Ubuntu Xenial 16.04 LTS ARM Hard Float
- Debian Stretch 9 ARM Hard Float
- Yocto Pyro ARM Hard Float
- Buildroot Skeltal ARM Hard Float
