Difference between revisions of "IGEP COM MODULE"
From IGEP - ISEE Wiki
(→Software) |
|||
Line 126: | Line 126: | ||
|} | |} | ||
+ | |||
+ | ==Documentation== | ||
+ | * [[DM3730|IGEP COM MODULE SoC: DM3730]] | ||
+ | * [http://downloads.isee.biz/pub/documentation/Platform_Boards/IGEP_COM_Module/Datasheet/IGEP_COM_MODULE_DATASHEET_20160712.pdf Datasheet] | ||
+ | * [http://downloads.isee.biz/pub/documentation/Platform_Boards/IGEP_COM_Module/Mechanical/MEC-PR-IGEP.0030-001.01-DRAWING.pdf Mechanical] | ||
+ | * Software Manual | ||
+ | * [http://downloads.isee.biz/pub/documentation/Platform_Boards/IGEP_COM_Module/Manuals/MAN-IGEP0030-RGx-IGEP_COM_MODULE_HARDWARE_REFERENCE_MANUAL-20160607.pdf Hardware Manual] | ||
+ | |||
+ | ==Tutorials== | ||
+ | # IGEP COM MODULE Boot Pin-out | ||
+ | # [http://labs.isee.biz/index.php/Prepare_a_ready_to_boot_firmware How to prepare a ready to boot firmware] | ||
+ | # [[The bootloader U-Boot|U-Boot Bootloader]] | ||
+ | # [[Linux Kernel 4.9.y|Linux Kernel]] | ||
+ | # [http://labs.isee.biz/index.php/IGEP_Firmware_set-up IGEP Firmware set-up] | ||
+ | # [[How to prepare a bootable MicroSD Card|Boot from MicroSD Card]] | ||
+ | # [[How to Flash the System into the NAND/eMMC|Boot from NAND/eMMC flash.]] | ||
+ | # [http://labs.isee.biz/index.php/Update_installed_IGEP_Firmware Update Installed IGEP Firmware] | ||
+ | |||
+ | ==Firmware== | ||
+ | ===Official=== | ||
+ | * [http://labs.isee.biz/index.php/IGEP_Firmware_set-up#Install_IGEP_Firmware_on_bootable_SD-card Official IGEP Firmware] | ||
+ | |||
+ | ===Software=== | ||
+ | * [http://downloads.isee.biz/pub/relaunch/rootfs/ubuntu/xenial/ubuntu-xenial-armhf-igep-base-v0.01.tgz Ubuntu Xenial 16.04 LTS ARM Hard Float] | ||
+ | * [http://downloads.isee.biz/pub/relaunch/rootfs/debian/stretch/debian-stretch-armhf-igep-base-v0.01.tgz Debian Stretch ARM Hard Float] | ||
+ | * [http://downloads.isee.biz/pub/relaunch/rootfs/yocto/pyro/minimal/igep0030hf-yocto-pyro-minimal-base-v0.01.bz2 Yocto Pyro ARM Hard Float] | ||
+ | * [http://downloads.isee.biz/pub/relaunch/rootfs/buildroot/skeltal/igep-buildroot-skeltal-base-v0.01.bz2 Buildroot ARM Hard Float] | ||
+ | |||
+ | ==<span dir="auto">Guides</span>== | ||
+ | ===Getting started with IGEP COM MODULE=== | ||
+ | * [[Getting started with IGEP COM MODULE|Getting Started with IGEP COM MODULE]] | ||
+ | |||
+ | ===Ubuntu / Debian=== | ||
+ | * [[How To Set Up an NFS Mount on Ubuntu 16.04]] | ||
+ | |||
+ | ===Yocto=== | ||
+ | * [[How to use the Yocto Project to develop Embedded Linux]] | ||
+ | |||
==Firmware== | ==Firmware== |
Revision as of 10:12, 25 September 2018
Contents
Small module SINGLE core ARM Cortex-A8 up to 1000 MHz
The IGEP COM MODULE is an industrial processor board. It can be used as a computer-on-module for your product. The IGEP COM MODULE provides a lot of features in a small size. You can build your project anywhere you want.
Features | |
---|---|
Processor |
DM3730 / AM3703, by Texas Instruments |
3D/2D Accelerator | PowerVR SGX GPU, providing graphics acceleration with OpenGL ES1.0, OpenGL ES2.0 and OpenVG support (Only in DM3730 version) |
Video |
Video acceleration: H.264, H.263, MPEG-4, MPEG-2, JPEG, WMV9 and additional codecs. Video encoder/decoder up to 720p (Only in DM3730 version) |
Memory | RAM: Up to 512 MB Mobile DDR (Standard setup 512 MB) Flash: Up to 512 MB (Standard setup 512 MB) Onboard micro-SD card socket |
Ethernet |
No |
USB |
1 x USB 2.0 Host (connector not included) |
Display |
1 x Digital Video/TFT interface |
Image Capture Interface | 1 x CPI interface (12 bits) |
Wireless |
WiFi IEEE 802.11 b/g/n (Access Point: Yes) |
Antenna |
1 x Internal WiFi/Bluetooth antenna |
Additional Interfaces
|
4 x UART |
SW Support | Linux Android |
Power Supply | Power from expansion connectors: From 3,5 V to 4,2 V Digital I/O voltage: 1,8 V |
Power Consumption | Typical 1 W (depending on software) Maximum 2 W (depending on software) |
Thermal | Commercial temperature: 0 ºC to +60 ºC Industrial temperature: -40 ºC to +85 ºC |
Form Factor | 18 mm x 68.5 mm Gumstix compatible |
Humidity | 93% relative Humidity at 40 ºC, non-condensing (according to IEC 60068-2-78) |
MTBF | > 100000 hours |
Options |
|
---|---|
Processor |
|
Grade |
|
Main Memory |
|
Flash Memory |
|
Wireless |
|
3D/2D Accelerator - Video |
|
Documentation
- IGEP COM MODULE SoC: DM3730
- Datasheet
- Mechanical
- Software Manual
- Hardware Manual
Tutorials
- IGEP COM MODULE Boot Pin-out
- How to prepare a ready to boot firmware
- U-Boot Bootloader
- Linux Kernel
- IGEP Firmware set-up
- Boot from MicroSD Card
- Boot from NAND/eMMC flash.
- Update Installed IGEP Firmware
Firmware
Official
Software
- Ubuntu Xenial 16.04 LTS ARM Hard Float
- Debian Stretch ARM Hard Float
- Yocto Pyro ARM Hard Float
- Buildroot ARM Hard Float
Guides
Getting started with IGEP COM MODULE
Ubuntu / Debian
Yocto
Firmware
Tutorials
- IGEP COM MODULE Boot Pin-out
- How to prepare a ready to boot firmware
- U-Boot Bootloader
- Linux Kernel
- IGEP Firmware set-up
- Boot from MicroSD Card
- Boot from NAND/eMMC flash.
- Update Installed IGEP Firmware
Documentation
- IGEP COM MODULE SoC: DM3730
- Datasheet
- Mechanical
- Software Manual
- Hardware Manual
Software
- Official IGEP Firmware
- Ubuntu Xenial 16.04 LTS ARM Hard Float
- Debian Stretch ARM Hard Float
- Yocto Pyro ARM Hard Float
- Buildroot ARM Hard Float