Difference between revisions of "Mux instructions"

From IGEP - ISEE Wiki

Jump to: navigation, search
(Overview)
 
(80 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
= Overview  =
 
= Overview  =
  
Detailed instructions to configure mux  
+
This wiki page has more detailed information about mux on IGEPv2. <br>
 +
Read general [[Mux configuration|'Mux configuration' page]] before use it. This article contains: <br>
  
See [[Mux configuration|this page]] for more information.
+
*How-to disable some external peripherals to avoid interferences
 +
*Some detailed examples.
  
= Feedback and Contributing =
+
= Disable Peripherals =
 +
 
 +
Some connectors share multiple peripherals like OMAP, WIFI/BT combo, etc. You should disable unused peripherals to avoid interferences. For example: if you want to control WIFI module via J990 disable OMAP or if you want use [[How to set up UART2 in J990|UART2 at j990]] disable Bluetooth. See schematics or [[Connectors Summary|connectors summary]] for more information.
 +
 
 +
=== BT/WIFI Combo  ===
  
At any point, if you see a mistake you can contribute to this How-To.
+
Bluetooth and WIFI can be disabled separately with reset pins: RESET_N_W (for WIFI) in pad 47 and RST_N_B (for Bluetooth) in pad 16:
  
= Disable Peripherals  =
+
*RESET_N_W/RST_N_B=0: Enabled reset
 +
*RESET_N_W/RST_N_B=1: Disabled reset
  
=== BT/WIFI  ===
+
Use GPIO to control it. See [[Frequently Asked Questions and Their Answers|FAQs]] to know which GPIO needs to be used.
  
See [[Frequently Asked Questions and Their Answers#Is_it_possible_to_config_the_wireless_LAN_and_bluetooth_so_they_are_completely_off.2C_and_not_consuming_any_power_at_all.3F|FAQ]] to see with pins need to configure.<br>
+
{| cellspacing="1" cellpadding="1" border="1" align="center" width="200"
 +
|-
 +
| [[Image:WIFI-BT Schematic.png|400x277px]]
 +
|}
  
More information about [[How to setup Marvell bluetooth|BT]] and [[How to setup Marvell 88w8686 SDIO wifi|WIFI]]
+
Click to enlarge image<br>
  
 
==== Bluetooth  ====
 
==== Bluetooth  ====
 +
 +
There are two ways to disable Bluetooth. More information about [[How to setup Marvell bluetooth|Bluetooth]]
  
 
===== First way:  =====
 
===== First way:  =====
Line 25: Line 37:
 
Logging with root user via SSH or Serial cable.<br>  
 
Logging with root user via SSH or Serial cable.<br>  
  
 +
NOTE: Poky distribution does not have debug filesystem enabled. Mount it:
 +
<pre>mount -t debugfs none /sys/kernel/debug</pre>
 
Go to /sys/kernel/debug/omap_mux/<br>  
 
Go to /sys/kernel/debug/omap_mux/<br>  
  
Line 67: Line 81:
 
'''Compile kernel source code'''  
 
'''Compile kernel source code'''  
  
Use this [[Linux Kernel 2.6.35.y|tutorial]] (Kernel) and this [http://labs.igep.es/index.php/The_IGEP_X-loader other] (IGEPxloader) to install Linaro Headless with your custom kernel in SD card.&nbsp; You can compile the IGEPxloader, but is not necessary.<br>  
+
Use this [[Linux Kernel 2.6.35.y|tutorial]] (Kernel) and this [http://labs.igep.es/index.php/The_IGEP_X-loader other] (IGEPxloader) to install Linaro Headless (or Poky) with your custom kernel in SD card.&nbsp; You can compile the IGEPxloader, but is not necessary.<br>  
  
 
==== WIFI  ====
 
==== WIFI  ====
 +
 +
There are two ways to disable WIFI. More information about [[How to setup Marvell 88w8686 SDIO wifi|WIFI]]
  
 
===== First way:  =====
 
===== First way:  =====
  
This mode has a issue, when your system reboot or shutdown you will need to configure again. Using user space to configure mux and disable WIFI.  
+
This mode has a issue, when your system reboot or shutdown you will need to configure again. Using user space to configure mux and disable WIFI. If you need bluetooth activate, configure it before disable WIFI. Follow [[How to setup Marvell bluetooth|this tutorial]].  
 
 
NOTE: If you need bluetooth, configure before disable WIFI. Follow [[How to setup Marvell bluetooth|this tutorial]].  
 
  
 
Logging with root user via SSH or Serial cable.<br>  
 
Logging with root user via SSH or Serial cable.<br>  
  
 +
NOTE: Poky distribution does not have debug filesystem enabled. Mount it:
 +
<pre>mount -t debugfs none /sys/kernel/debug</pre>
 
Go to /sys/kernel/debug/omap_mux/<br>  
 
Go to /sys/kernel/debug/omap_mux/<br>  
  
 
Set sdmmc2_dat6 to gpio138 (mode 4):  
 
Set sdmmc2_dat6 to gpio138 (mode 4):  
<pre>echo 0x004 &gt; sdmmc2_dat6 </pre>  
+
<pre>echo 0x004 &gt; sdmmc2_dat7</pre>  
 
Revise that:  
 
Revise that:  
<pre>root@localhost:/sys/kernel/debug/omap_mux# cat sdmmc2_dat6
+
<pre>root@localhost:/sys/kernel/debug/omap_mux# cat sdmmc2_dat7
name: sdmmc2_dat6.gpio_138 (0x48002168/0x138 = 0x0004), b af3, t NA
+
name: sdmmc2_dat7.gpio_139 (0x4800216a/0x13a = 0x0004), b ae3, t NA
 
mode: OMAP_PIN_OUTPUT | OMAP_MUX_MODE4
 
mode: OMAP_PIN_OUTPUT | OMAP_MUX_MODE4
signals: sdmmc2_dat6 | sdmmc2_dir_cmd | cam_shutter | sdmmc3_dat2 | gpio_138 | hsusb3_tll_dir | NA | safe_mode
+
signals: sdmmc2_dat7 | sdmmc2_clkin | NA | sdmmc3_dat3 | gpio_139 | hsusb3_tll_nxt | mm3_rxdm | safe_mode
 
root@localhost:/sys/kernel/debug/omap_mux#  
 
root@localhost:/sys/kernel/debug/omap_mux#  
 
</pre>  
 
</pre>  
 
Go to: /sys/class/gpio/  
 
Go to: /sys/class/gpio/  
  
Check that gpio138 is in user space:  
+
Check that gpio139 is in user space:  
 
<pre>root@localhost:/sys/class/gpio# ls
 
<pre>root@localhost:/sys/class/gpio# ls
export   gpio137  gpio140 gpio157 gpio64       gpiochip160 gpiochip64
+
export gpio137  gpio138  gpio139 gpio170 gpio64  gpiochip0 gpiochip128 gpiochip160 gpiochip192  gpiochip32 gpiochip64 gpiochip96 unexport
gpio126 gpio138 gpio141 gpio167  gpiochip0    gpiochip192  gpiochip96
 
gpio136 gpio139 gpio156 gpio170  gpiochip128  gpiochip32  unexport
 
 
root@localhost:/sys/class/gpio#  
 
root@localhost:/sys/class/gpio#  
 
</pre>  
 
</pre>  
If you don't have it, you should export gpio138: <br>  
+
If you don't have it, you should export gpio139: <br>  
<pre>echo 138 &gt; /sys/class/gpio/export </pre>  
+
<pre>echo 139 &gt; /sys/class/gpio/export </pre>  
Set gpio138 to low value to disable bluetooth:  
+
Set gpio139 to low value to disable bluetooth:  
<pre>echo 0 &gt; /sys/class/gpio/gpio138/value</pre>  
+
<pre>echo 0 &gt; /sys/class/gpio/gpio139/value</pre>  
 
Revise that:  
 
Revise that:  
<pre>root@localhost:/sys/class/gpio# cat /sys/class/gpio/gpio138/value  
+
<pre>root@localhost:/sys/class/gpio# cat /sys/class/gpio/gpio139/value  
 
0
 
0
 
root@localhost:/sys/class/gpio#  
 
root@localhost:/sys/class/gpio#  
 
</pre>  
 
</pre>  
===== Second way:  =====
+
===== Second way&nbsp;:  =====
 
 
Configure kernel sources. Configuration will be permanent. There are many ways to edit source code, this method is focused for igep0020 RC without igep0022 support. <br>
 
  
<br> Go to [http://git.igep.es/?p=pub/scm/linux-omap-2.6.git;a=blob_plain;f=arch/arm/mach-omap2/board-igep00x0.c;hb=e620ef8e577d73681f16ab80471332286c1b9fd5 $(kernel path)/arch/arm/mach-omap2/board-igep00x0.c] and search next line: <br>  
+
Configure kernel sources. Configuration will be permanent. There are many ways to edit source code, this method is focused for igep0020 RC without igep0022 support. <br> Go to [http://git.igep.es/?p=pub/scm/linux-omap-2.6.git;a=blob_plain;f=arch/arm/mach-omap2/board-igep00x0.c;hb=e620ef8e577d73681f16ab80471332286c1b9fd5 $(kernel path)/arch/arm/mach-omap2/board-igep00x0.c] and search next line: <br>  
 
<pre> if ((gpio_request(wifi_nreset, "WIFI NRESET") == 0) &amp;&amp;
 
<pre> if ((gpio_request(wifi_nreset, "WIFI NRESET") == 0) &amp;&amp;
 
    (gpio_direction_output(wifi_nreset, 1) == 0)) {
 
    (gpio_direction_output(wifi_nreset, 1) == 0)) {
Line 119: Line 131:
 
udelay(10);
 
udelay(10);
 
gpio_set_value(wifi_nreset, 1);
 
gpio_set_value(wifi_nreset, 1);
} </pre>  
+
} else </pre>  
p
+
"igep00x0_wifi_bt_init" function initializes WIFI and Bluetooth peripherals, this code make a PWM to initialize WIFI. Edit lines to disable this initialization.<br>
<pre> if ((gpio_request(wifi_nreset, "WIFI NRESET") == 0) &amp;&amp;
+
<pre> if ((gpio_request(wifi_nreset, "WIFI NRESET") == 0) &amp;&amp;
    (gpio_direction_output(wifi_nreset, 1) == 0)) {
+
    (gpio_direction_output(wifi_nreset, 0) == 0)) {
 
gpio_export(wifi_nreset, 0);
 
gpio_export(wifi_nreset, 0);
gpio_set_value(wifi_nreset, 0);
 
//udelay(10);
 
//gpio_set_value(wifi_nreset, 1);
 
} </pre>
 
Please contribute
 
  
=== TP65950 PCM VSP<br> ===
+
} else </pre>
 +
'''Compile kernel source code'''
 +
 
 +
Use this [[Linux Kernel 2.6.35.y|tutorial]] (Kernel) and this [http://labs.igep.es/index.php/The_IGEP_X-loader other] (IGEPxloader) to install Linaro Headless (or Poky) with your custom kernel in SD card.&nbsp; You can compile the IGEPxloader, but is not necessary.<br>
 +
 
 +
=== TP65950 PCM VSP  ===
 +
 
 +
This module is used to transfer audio via Bluetooth
 +
 
 +
{| cellspacing="1" cellpadding="1" border="1" align="center" width="200"
 +
|-
 +
| [[Image:TPS-PCM-VSP.png|800x164px]]
 +
|}
 +
 
 +
Click to enlarge image
  
==== Disable BT audio<br> ====
+
'''Disable BT audio'''<br>  
  
 
Default kernel&nbsp; has disabled TWL4030 PCM voice interface output pins to high impedance, otherwise this module forces the level of mcbsp3_fsx and mcbsp3_clkx pins. To make sure, go to [http://git.igep.es/?p=pub/scm/linux-omap-2.6.git;a=blob_plain;f=sound/soc/codecs/twl4030.c;hb=linux-2.6.35.y $(kernel path)/sound/soc/codecs/twl4030.c] file already read: <br>  
 
Default kernel&nbsp; has disabled TWL4030 PCM voice interface output pins to high impedance, otherwise this module forces the level of mcbsp3_fsx and mcbsp3_clkx pins. To make sure, go to [http://git.igep.es/?p=pub/scm/linux-omap-2.6.git;a=blob_plain;f=sound/soc/codecs/twl4030.c;hb=linux-2.6.35.y $(kernel path)/sound/soc/codecs/twl4030.c] file already read: <br>  
 
<pre> 0x04, /* REG_VOICE_IF (0xF) */
 
<pre> 0x04, /* REG_VOICE_IF (0xF) */
 
</pre>  
 
</pre>  
==== Enable BT audio<br> ====
+
'''Enable BT audio'''<br>  
 
<pre> 0x00, /* REG_VOICE_IF (0xF) */
 
<pre> 0x00, /* REG_VOICE_IF (0xF) */
 +
 
</pre>  
 
</pre>  
<br>
+
<br>
 +
 
 +
=== TFP410  ===
 +
 
 +
This external peripheral converts DVI signal to HDMI. To use some JA41/JA42 pads for other purpose is necessary disable it. GPIO_170 control TFP410 Power down (PD pad).
 +
 
 +
Power down (active low). In the powerdown state, only the digital I/O buffers and I2C interface remain active. A high level selects the normal operating mode. A low level selects the powerdown mode.<br>  
  
= Edit mux =
+
It was tested using alternate peripherals like UARTs and GPIOs. Caution, in powerdown mode, pads aren't in safe mode (high impedance).
 +
 
 +
{| cellspacing="1" cellpadding="1" border="1" align="center" width="200"
 +
|-
 +
| [[Image:Tfp410 IGEPv2.png|713x462px]]
 +
|}
 +
 
 +
<br>
 +
 
 +
===== First way: =====
 +
 
 +
This mode has a issue, when your system reboot or shutdown you will need to configure again. Using user space to configure mux and powerdown TFP410.
 +
 
 +
Logging with root user via SSH or Serial cable.<br>
 +
 
 +
NOTE: Poky distribution does not have debug filesystem enabled. Mount it:
 +
<pre>mount -t debugfs none /sys/kernel/debug</pre>
 +
Go to /sys/kernel/debug/omap_mux/<br>
  
=== UART1 in J990  ===
+
Set hdq_sio to gpio170 (mode 4):
 +
<pre>echo 0x104 &gt; hdp_sio</pre>
 +
Revise that:
 +
<pre>root@localhost:/sys/kernel/debug/omap_mux# cat hdq_sio
 +
name: hdq_sio.gpio_170 (0x480021c6/0x196 = 0x0104), b j25, t NA
 +
mode: OMAP_PIN_INPUT | OMAP_MUX_MODE4
 +
signals: hdq_sio | sys_altclk | i2c2_sccbe | i2c3_sccbe | gpio_170 | NA | NA | safe_mode
 +
root@localhost:/sys/kernel/debug/omap_mux#
 +
</pre>
 +
Go to: /sys/class/gpio/
  
Use ebuddies to configure UART1 in J990, go to igep.ini:  
+
Check that gpio170 is in user space:
 +
<pre>root@localhost:/sys/class/gpio# ls
 +
export  gpio137  gpio138  gpio139  gpio170  gpio64  gpiochip0  gpiochip128  gpiochip160  gpiochip192  gpiochip32  gpiochip64  gpiochip96  unexport
 +
root@localhost:/sys/class/gpio#
 +
</pre>
 +
If you don't have it, you should export gpio170: <br>
 +
<pre>echo 170 &gt; /sys/class/gpio/export </pre>
 +
Set gpio170 to low value to disable TFP410:
 +
<pre>echo 0 &gt; /sys/class/gpio/gpio170/value</pre>
 +
Revise that:
 +
<pre>root@localhost:/sys/class/gpio# cat /sys/class/gpio/gpio170/value
 +
0
 +
root@localhost:/sys/class/gpio#
 +
</pre>
 +
===== Second way&nbsp;: =====
  
  board.ei485= [yes, no]
+
Configure kernel sources. Configuration will be permanent. There are many ways to edit source code, this method is focused for igep0020 RC without igep0022 support. <br> Go to [http://git.igep.es/?p=pub/scm/linux-omap-2.6.git;a=blob_plain;f=arch/arm/mach-omap2/board-igep0020.c;hb=db3cb47adf10504d3847d54927de50b2fa94c008 $(kernel path)/arch/arm/mach-omap2/board-igep0020.c] and search next line: <br>
                Format: &lt;string&gt;
+
<pre> static inline void igep0020_display_init(void)
                no: disable ei485, use UART1 as RS232, supported by igep0020
+
static int igep0020_enable_dvi(struct omap_dss_device *dssdev)
                default: yes
+
{
 +
gpio_direction_output(GPIO_DVI_PUP, 1);
  
More information about RS485 [[Connectors Summary#J940_connector|here]] and [http://en.wikipedia.org/wiki/RS-485 here]
+
return 0;
 +
}
 +
</pre>
 +
"static int igep0020_enable_dvi" initialize DVI. Edit to disable it:
 +
<pre>static int igep0020_enable_dvi(struct omap_dss_device *dssdev)
 +
{
 +
gpio_direction_output(GPIO_DVI_PUP, 0);
  
You can test new configuration using [[How to use UARTs|this tutorial]]
+
return 0;
 +
}
 +
</pre>
 +
'''Compile kernel source code'''
  
=== GPIO in J990  ===
+
Use this [[Linux Kernel 2.6.35.y|tutorial]] (Kernel) and this [http://labs.igep.es/index.php/The_IGEP_X-loader other] (IGEPxloader) to install Linaro Headless (or Poky) with your custom kernel in SD card.&nbsp; You can compile the IGEPxloader, but is not necessary.<br>
  
Reset [[Mux instructions#WIFI|WIFI]], [[Mux instructions#Bluetooth|BT]] or [[Mux instructions#TP65950_PCM_VSP|TPS]] if you use some pad shared with this connector,
+
= Edit mux  =
  
Configure GPIO, don't use [[Frequently_Asked_Questions_and_Their_Answers#Is_it_possible_to_config_the_wireless_LAN_and_bluetooth_so_they_are_completely_off.2C_and_not_consuming_any_power_at_all.3F|these GPIO]] in IGEP WIFI/BT versions.<br>
+
Here you can found some detailed examples to configure mux. You can add more.  
  
Please contribute
+
=== UART1 in J960  ===
  
More information [[Connectors Summary#J990_connector|here]].<br>
+
Use ebuddies to configure UART1 in J960, go to igep.ini:
  
=== GPIO in JTAG ===
+
  board.ei485[yes, no]
 +
                Format: &lt;string&gt;
 +
                no: disable ei485, use UART1 as RS232, supported by igep0020
 +
                default: yes
  
Please contribute<br>
+
More information about RS485 [[Connectors Summary#J940_connector|here]] and [http://en.wikipedia.org/wiki/RS-485 here]
  
=== GPIO in JC30 ===
+
You can test new configuration using [[How to use UARTs|this tutorial]]<br>
  
Please contribute<br>
+
=== UART3 in J960  ===
  
=== GPIO in JA42 ===
+
Edit igep.ini to disable serial debug, comment next lines:
 +
<pre>; Setup the Kernel console params
 +
;console=ttyO2,115200n8
 +
;console=ttyS2,115200n8
 +
; Enable early printk
 +
;earlyprintk=serial,tty02,115200
 +
;earlyprintk=serial,ttyS2,115200 </pre>
  
Please contribute<br>
+
Poky linux starts an user terminal at UART3, You must disable it to avoid interferences. Comment next lines in /etc/inittab:
  
=== GPIO in JA41 ===
+
<pre># Normally not reached, but fallthrough in case of emergency.
 +
#z6:6:respawn:/sbin/sulogin
 +
#S:2345:respawn:/sbin/getty 115200 ttyO2
 +
# /sbin/getty invocations for the runlevels.
 +
</pre>
  
Please contribute<br>
+
You can test new configuration using [[How to use UARTs|this tutorial]]<br>
  
=== GPIO in TP ===
+
=== GPIO in J990  ===
  
Please contribute<br>
+
Reset [[Mux instructions#WIFI|WIFI]], [[Mux instructions#Bluetooth|BT]] or [[Mux instructions#TP65950_PCM_VSP|TPS]] if you use some pad shared with this connector, more information [[Connectors Summary#J990_connector|here]].
  
 +
Configure GPIO, don't use [[Frequently Asked Questions and Their Answers#Is_it_possible_to_config_the_wireless_LAN_and_bluetooth_so_they_are_completely_off.2C_and_not_consuming_any_power_at_all.3F|these GPIO]] in IGEP WIFI/BT versions.<br>
  
 +
Use [[How to use GPIOs|this manual]] to configure mux via user space<br>
  
'''Under construction'''
+
Edit&nbsp; [http://git.igep.es/?p=pub/scm/linux-omap-2.6.git;a=blob_plain;f=arch/arm/mach-omap2/board-igep00x0.c;hb=e620ef8e577d73681f16ab80471332286c1b9fd5 $(kernel path)/arch/arm/mach-omap2/board-igep00x0.c]&nbsp; or [http://git.igep.es/?p=pub/scm/linux-omap-2.6.git;a=blob_plain;f=arch/arm/mach-omap2/board-igep0020.c;hb=refs/heads/linux-2.6.35.y $(kernel path)/arch/arm/mach-omap2/board-igep0020.c] to configure GPIO via Kernel source, example [[How to set up UART2 in J990#Third_way|here]].<br>
  
[[Category:How_to_forge]] [[Category:Tutorials]]
+
[[Category:Peripherals]]

Latest revision as of 19:30, 13 February 2013

Overview

This wiki page has more detailed information about mux on IGEPv2.
Read general 'Mux configuration' page before use it. This article contains:

  • How-to disable some external peripherals to avoid interferences
  • Some detailed examples.

Disable Peripherals

Some connectors share multiple peripherals like OMAP, WIFI/BT combo, etc. You should disable unused peripherals to avoid interferences. For example: if you want to control WIFI module via J990 disable OMAP or if you want use UART2 at j990 disable Bluetooth. See schematics or connectors summary for more information.

BT/WIFI Combo

Bluetooth and WIFI can be disabled separately with reset pins: RESET_N_W (for WIFI) in pad 47 and RST_N_B (for Bluetooth) in pad 16:

  • RESET_N_W/RST_N_B=0: Enabled reset
  • RESET_N_W/RST_N_B=1: Disabled reset

Use GPIO to control it. See FAQs to know which GPIO needs to be used.

WIFI-BT Schematic.png

Click to enlarge image

Bluetooth

There are two ways to disable Bluetooth. More information about Bluetooth

First way:

This mode has a issue, when your system reboot or shutdown you will need to configure again. Using user space to configure mux and disable bluetooth.

Logging with root user via SSH or Serial cable.

NOTE: Poky distribution does not have debug filesystem enabled. Mount it:

mount -t debugfs none /sys/kernel/debug

Go to /sys/kernel/debug/omap_mux/

Set sdmmc2_dat5 to gpio137 (mode 4):

echo 0x004 > sdmmc2_dat5 

Revise that:

root@localhost:/sys/kernel/debug/omap_mux# cat sdmmc2_dat5
name: sdmmc2_dat5.gpio_137 (0x48002166/0x136 = 0x0004), b ah3, t NA
mode: OMAP_PIN_OUTPUT | OMAP_MUX_MODE4
signals: sdmmc2_dat5 | sdmmc2_dir_dat1 | cam_global_reset | sdmmc3_dat1 | gpio_137 | hsusb3_tll_stp | mm3_rxdp | safe_mode

Go to: /sys/class/gpio/

Check that gpio137 is in user space:

root@localhost:/sys/class/gpio# ls
export  gpio137  gpio138  gpio139  gpio170  gpio64  gpiochip0  gpiochip128  gpiochip160  gpiochip192  gpiochip32  gpiochip64  gpiochip96  unexport
root@localhost:/sys/class/gpio# 

If you don't have it, you should export gpio137:

echo 137 > /sys/class/gpio/export 

Set gpio137 to low value to disable bluetooth:

echo 0 > /sys/class/gpio/gpio137/value

Revise that:

root@localhost:/sys/class/gpio# cat /sys/class/gpio/gpio137/value 
0
root@localhost:/sys/class/gpio# 
Second way:

Configure kernel sources. Configuration will be permanent. There are many ways to edit source code, this method is focused for igep0020 RC without igep0022 support.

Go to $(kernel path)/arch/arm/mach-omap2/board-igep0020.c and search next line:

	else if (hwrev == IGEP2_BOARD_HWREV_C)
		igep00x0_wifi_bt_init(IGEP2_RC_GPIO_WIFI_NPD,
			IGEP2_RC_GPIO_WIFI_NRESET, IGEP2_RC_GPIO_BT_NRESET,
			!opt); 

"igep00x0_wifi_bt_init" function initializes WIFI and Bluetooth peripherals. "opt" variable is used for disable Bluetooth in some cases: enabled (opt!=0) or disabled (opt==0). For example you can disable it permanently replacing "opt" by 1:

	else if (hwrev == IGEP2_BOARD_HWREV_C)
		igep00x0_wifi_bt_init(IGEP2_RC_GPIO_WIFI_NPD,
			IGEP2_RC_GPIO_WIFI_NRESET, IGEP2_RC_GPIO_BT_NRESET,
			!1); 

Compile kernel source code

Use this tutorial (Kernel) and this other (IGEPxloader) to install Linaro Headless (or Poky) with your custom kernel in SD card.  You can compile the IGEPxloader, but is not necessary.

WIFI

There are two ways to disable WIFI. More information about WIFI

First way:

This mode has a issue, when your system reboot or shutdown you will need to configure again. Using user space to configure mux and disable WIFI. If you need bluetooth activate, configure it before disable WIFI. Follow this tutorial.

Logging with root user via SSH or Serial cable.

NOTE: Poky distribution does not have debug filesystem enabled. Mount it:

mount -t debugfs none /sys/kernel/debug

Go to /sys/kernel/debug/omap_mux/

Set sdmmc2_dat6 to gpio138 (mode 4):

echo 0x004 > sdmmc2_dat7

Revise that:

root@localhost:/sys/kernel/debug/omap_mux# cat sdmmc2_dat7
name: sdmmc2_dat7.gpio_139 (0x4800216a/0x13a = 0x0004), b ae3, t NA
mode: OMAP_PIN_OUTPUT | OMAP_MUX_MODE4
signals: sdmmc2_dat7 | sdmmc2_clkin | NA | sdmmc3_dat3 | gpio_139 | hsusb3_tll_nxt | mm3_rxdm | safe_mode
root@localhost:/sys/kernel/debug/omap_mux# 

Go to: /sys/class/gpio/

Check that gpio139 is in user space:

root@localhost:/sys/class/gpio# ls
export  gpio137  gpio138  gpio139  gpio170  gpio64  gpiochip0  gpiochip128  gpiochip160  gpiochip192  gpiochip32  gpiochip64  gpiochip96  unexport
root@localhost:/sys/class/gpio# 

If you don't have it, you should export gpio139:

echo 139 > /sys/class/gpio/export 

Set gpio139 to low value to disable bluetooth:

echo 0 > /sys/class/gpio/gpio139/value

Revise that:

root@localhost:/sys/class/gpio# cat /sys/class/gpio/gpio139/value 
0
root@localhost:/sys/class/gpio# 
Second way :

Configure kernel sources. Configuration will be permanent. There are many ways to edit source code, this method is focused for igep0020 RC without igep0022 support.
Go to $(kernel path)/arch/arm/mach-omap2/board-igep00x0.c and search next line:

	if ((gpio_request(wifi_nreset, "WIFI NRESET") == 0) &&
	    (gpio_direction_output(wifi_nreset, 1) == 0)) {
		gpio_export(wifi_nreset, 0);
		gpio_set_value(wifi_nreset, 0);
		udelay(10);
		gpio_set_value(wifi_nreset, 1);
	} else 

"igep00x0_wifi_bt_init" function initializes WIFI and Bluetooth peripherals, this code make a PWM to initialize WIFI. Edit lines to disable this initialization.

		if ((gpio_request(wifi_nreset, "WIFI NRESET") == 0) &&
	    (gpio_direction_output(wifi_nreset, 0) == 0)) {
		gpio_export(wifi_nreset, 0);

	} else 

Compile kernel source code

Use this tutorial (Kernel) and this other (IGEPxloader) to install Linaro Headless (or Poky) with your custom kernel in SD card.  You can compile the IGEPxloader, but is not necessary.

TP65950 PCM VSP

This module is used to transfer audio via Bluetooth

TPS-PCM-VSP.png

Click to enlarge image

Disable BT audio

Default kernel  has disabled TWL4030 PCM voice interface output pins to high impedance, otherwise this module forces the level of mcbsp3_fsx and mcbsp3_clkx pins. To make sure, go to $(kernel path)/sound/soc/codecs/twl4030.c file already read:

	0x04, /* REG_VOICE_IF		(0xF)	*/

Enable BT audio

	0x00, /* REG_VOICE_IF		(0xF)	*/


TFP410

This external peripheral converts DVI signal to HDMI. To use some JA41/JA42 pads for other purpose is necessary disable it. GPIO_170 control TFP410 Power down (PD pad).

Power down (active low). In the powerdown state, only the digital I/O buffers and I2C interface remain active. A high level selects the normal operating mode. A low level selects the powerdown mode.

It was tested using alternate peripherals like UARTs and GPIOs. Caution, in powerdown mode, pads aren't in safe mode (high impedance).

Tfp410 IGEPv2.png


First way:

This mode has a issue, when your system reboot or shutdown you will need to configure again. Using user space to configure mux and powerdown TFP410.

Logging with root user via SSH or Serial cable.

NOTE: Poky distribution does not have debug filesystem enabled. Mount it:

mount -t debugfs none /sys/kernel/debug

Go to /sys/kernel/debug/omap_mux/

Set hdq_sio to gpio170 (mode 4):

echo 0x104 > hdp_sio

Revise that:

root@localhost:/sys/kernel/debug/omap_mux# cat hdq_sio 
name: hdq_sio.gpio_170 (0x480021c6/0x196 = 0x0104), b j25, t NA
mode: OMAP_PIN_INPUT | OMAP_MUX_MODE4
signals: hdq_sio | sys_altclk | i2c2_sccbe | i2c3_sccbe | gpio_170 | NA | NA | safe_mode
root@localhost:/sys/kernel/debug/omap_mux# 

Go to: /sys/class/gpio/

Check that gpio170 is in user space:

root@localhost:/sys/class/gpio# ls
export  gpio137  gpio138  gpio139  gpio170  gpio64  gpiochip0  gpiochip128  gpiochip160  gpiochip192  gpiochip32  gpiochip64  gpiochip96  unexport
root@localhost:/sys/class/gpio# 

If you don't have it, you should export gpio170:

echo 170 > /sys/class/gpio/export 

Set gpio170 to low value to disable TFP410:

echo 0 > /sys/class/gpio/gpio170/value

Revise that:

root@localhost:/sys/class/gpio# cat /sys/class/gpio/gpio170/value 
0
root@localhost:/sys/class/gpio# 
Second way :

Configure kernel sources. Configuration will be permanent. There are many ways to edit source code, this method is focused for igep0020 RC without igep0022 support.
Go to $(kernel path)/arch/arm/mach-omap2/board-igep0020.c and search next line:

	static inline void igep0020_display_init(void)
static int igep0020_enable_dvi(struct omap_dss_device *dssdev)
{
	gpio_direction_output(GPIO_DVI_PUP, 1);

	return 0;
}

"static int igep0020_enable_dvi" initialize DVI. Edit to disable it:

static int igep0020_enable_dvi(struct omap_dss_device *dssdev)
{
	gpio_direction_output(GPIO_DVI_PUP, 0);

	return 0;
}

Compile kernel source code

Use this tutorial (Kernel) and this other (IGEPxloader) to install Linaro Headless (or Poky) with your custom kernel in SD card.  You can compile the IGEPxloader, but is not necessary.

Edit mux

Here you can found some detailed examples to configure mux. You can add more.

UART1 in J960

Use ebuddies to configure UART1 in J960, go to igep.ini:

 board.ei485=  [yes, no]
               Format: <string>
               no: disable ei485, use UART1 as RS232, supported by igep0020
               default: yes

More information about RS485 here and here

You can test new configuration using this tutorial

UART3 in J960

Edit igep.ini to disable serial debug, comment next lines:

; Setup the Kernel console params
;console=ttyO2,115200n8
;console=ttyS2,115200n8
; Enable early printk
;earlyprintk=serial,tty02,115200
;earlyprintk=serial,ttyS2,115200 

Poky linux starts an user terminal at UART3, You must disable it to avoid interferences. Comment next lines in /etc/inittab:

# Normally not reached, but fallthrough in case of emergency.
#z6:6:respawn:/sbin/sulogin
#S:2345:respawn:/sbin/getty 115200 ttyO2
# /sbin/getty invocations for the runlevels.

You can test new configuration using this tutorial

GPIO in J990

Reset WIFI, BT or TPS if you use some pad shared with this connector, more information here.

Configure GPIO, don't use these GPIO in IGEP WIFI/BT versions.

Use this manual to configure mux via user space

Edit  $(kernel path)/arch/arm/mach-omap2/board-igep00x0.c  or $(kernel path)/arch/arm/mach-omap2/board-igep0020.c to configure GPIO via Kernel source, example here.