How to use UARTs

From IGEP - ISEE Wiki

Revision as of 12:42, 3 September 2012 by Pau (talk | contribs)

Jump to: navigation, search

Overview

This How-To is meant to be a starting point for people to learn use UART for IGEP devices as quickly and easily as possible. In this how-to, we use IGEP Firmware and a program that use UART peripherals. This How-to was tested in:

Example program has a debug option using GPIOs to debug via oscilloscope, this method is useful to learn about the Kernel latencies. Debug has set to "write" and "select" functions. More information.


Preparing IGEP

Configure UART1 and UART3 in IGEP with RS232 levels on J960 connector

Edit igep.ini file

To test UARTs we use UART1 (dev/ttyO0) and UART3 (dev/ttyO2) via J960 connector using RS232 standard.

  • UART1 can used by RS485 driver, we need to disable it, edit igep.ini file:
board.ei485= yes
  • UART1 is configured in RS232 driver, when igep line is replaced by (or type in -Maybe you don't found this line-):
board.ei485= no
  • By default, UART3 is used by Kernel serial console, we need to disable it, go to igep.ini file, comment next line:
;console=ttyO2,115200n8
;console=ttyO

Edit inittab file

Getty program uses /dev/ttyO2 in IGEP Firmware, disable it modifying /dev/inittab file:

  • Comment next line:
 #S:2345:respawn:/sbin/getty 115200 ttyO2

Check UARTs devices

Make sure that Kernel detects UARTs, type:

dmesg | grep tty

The result will be similar at that:

root@igep00x0:~# dmesg | grep tty
[    0.000000] console [tty0] enabled
[    0.485198] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
[    0.485565] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
[    0.485931] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
[    0.486267] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3
root@igep00x0:~# 

Connect peripherals

Connect IGEPv2 board using J960 connector like this:

 J960    
                  ------  
    (Not used) x---| 1  2 |---o (Connect to 8)
(Connect to 9) o---| 3  4 |---x (Not used)
         (GND)·|---| 5  6 |---|· (GND)
     (Not used)x---| 7  8 |---o (Connect to 2)
(Connect to 3) o---| 9 10 |---x (Not used)
                  ------  

Send some data

Use microcom to prove it, open two terminals via SSH and log with root user:

Terminal 1:

microcom /dev/ttyO0

Terminal 2:

microcom /dev/ttyO2 

Type something in one terminal.

Schematics

RS232 Schematic Igep V2

RS232 Schematic Igep V2.png


Uart Schematic Igep Module

Uart Schematic Igep Module.png

Compile and run program

Download program source and extract it. Before compiling the program, there are some interesting things to configure. Open program and seek next lines:

//Define Array char size
#define SIZE 30

//Define Debug mode:0==Disable
#define DEBUG 0

//Define wait select
#define WAIT 5

//Set GPIO Debugger port
//Be sure that mux is correctly configured and GPIOs are not used
#define GPIO1 158
#define GPIO2 162

Constant SIZE: it determines the max number of chars sended.

Constant DEBUG: it can break program infinite loop part, useful to debug errors: 0 (infinite loop) or positive number determines loop max entrances.

Constant WAIT: it configures select max time in seconds.

Constants GPIO1 and GPIO2: they configure GPIOs used for debug via oscilloscope. By default, 158 and 162 values are not used in IGEPv2. Configure mux properly if you use other GPIOs.

Compile source code using a cross compiler for example IGEP SDK:

arm-poky-linux-gnueabi-gcc  uart-test-2-beta1.c -o uart-test-beta1 

Testing UART

Some tests do it:

Decode Characters

Decoded with ASCII table.

Uart decode1withlf.JPG Uart decode0withlf.JPG Uart decode100000withlf.JPG
Decoding "1\n" Decoding "0\n" Decoding "100000\n"

Click to enlarge image

select timeout

Program sends information via UART1 but don't receive response via UART3, because only a process is executed. This problem is repeated every 5 seconds (constant WAIT=5) until other process sends information via UART3 at the same speed. If "select" hasn't been implemented, process would have stayed blocked.

Uart select timeout9.JPG
UART1=Blue and UART3=Green

Click to enlarge image

RS232 Voltage params

More information here.

Uart voltageparams8.JPG
Vpp=11.8V aprox , Vmin=-5.6V aprox

Click to enlarge image

Speed Overview

Note that wave is degraded when speed is higher

Uart 300 o.JPG Uart 4800 o.JPG Uart 115200 o.JPG Uart 3000000 o.JPG
Overview signal to 300 bauds Overview signal to 4800 bauds Overview signal to 115200 bauds Overview signal to 3000000 bauds
Uart 300 s.JPG Uart 4800 s.JPG Uart 115200 s.JPG Uart 3000000 s.JPG
Specific wave to 300 bauds Specific wave to 4800 bauds Specific wave to 115200 bauds
Specific wave to 3000000 bauds

Click to enlarge image

Lag

You can see that RS232 have some lag between transmisions. This caused mainly by kernel process management. UART peripheral is controlled by Linux and It isn't a real-time operating system

Uart lag left6.JPG Uart lag right7.JPGselect: blocked until all data is available.
Lag between UART1 and UART3 (300 bauds) Lag between UART3 and UART1 (300 bauds)

Click to enlarge image

This program have three I/O functions that connect to UART driver via ioctl: (read(), write() and select()). But select() and write() change process stat to sleep mode until system don't receive or transmit all information via UART. "select" function is used to prevent that read function can be blocked when data aren't available.
The next images (program with debug_gpio enabled and 300 bauds speed) show when process is executed or is waiting. Blue=UART1, Violet="write" and Green="select". When GPIO has HIGH value, process is blocked.

Uart select5.JPG Uart select to write1.JPG Uart write2.JPG Uart write to select0.JPG
select function time Time between select and write write function time Time between write and select

Click to enlarge image

In this case:

select: blocked until all data is available (LF char received).

write: blocked until all data is send to UART buffer.

Error test

Every full process the number is increased twice. Program checks that this condicion is true, if it isn't accomplished, process will be finish.

Uart error test2.png
Runs 16h without any transfer error (3000000 bauds)