Mux configuration
From IGEP - ISEE Wiki
Explanation
| Pad: | Connect to: | Default peripheral (mode=0) | Default function: | Other available peripherals: | Share with: | |
| 1 | VIO 1V8 | - | Power 1v8 | - | ||
| 2 | DC 5V | - | Power 5v | - | ||
| 3 | MMC2_DAT7 | MMC2_DAT7 | Reset Wlan |
MMC2_CLKIN(mode=1) MMC3_DAT3(mode=3) GPIO_139(mode=4) |
Wlan: This pad can reset Wlan peripheral using Omap GPIO low level (GND). If you reset continuously Wlan all their pads are in High Impedance. Also you can disable Wlan from J990 low level. Omap: protect Omap pad if you don't
use it.(1)
| |
| 5 | MMC2_DAT6 | MMC2_DAT6 | Power down Wlan |
MMC2_DIR_CMD(mode=1) MMC3_DAT2(mode=3) GPIO_138(mode=4) |
Wlan: This pad can power down Wlan peripheral using Omap GPIO low level (GND), power up removing GND. Also you can power down Wlan from J990 low level. Omap: protect Omap pad if you don't
use it.(1)
| |
| 7 | MMC2_DAT5 | MMC2_DAT5 | Reset Bluethoot |
MMC2_DIR_DAT1(mode=1) MMC3_DAT1(mode=3) GPIO_137(mode=4) |
Bluethoot: This pad can reset Bluethoot
peripheral using Omap GPIO low level (GND). If you reset continuously Bluethoot all their pads are in High Impedance. Also you can disable
Omap: protect Omap pad if you don't
use it.(1)
| |
| 9 | MMC2_DAT4 | MMC2_DAT4 | - |
MMC_DIR_DAT0(mode=1) MMC3_DAT0(mode=3) GPIO136(mode=4) |
Wlan: Protect Wlan if you don' use
it. See MMC2_DAT7 pad. Omap: protect Omap pad if you don't
use it.(1)
| |
| 11 | MMC2_DAT3 | MMC2_DAT3 | (1)Transfer data between Omap and Wlan |
McSPI3_CS0(mode=1) GPIO_135(mode=4) |
<span style="font-weight: normal" /> | |
| 13 | MMC2_DAT2 | MMC2_DAT2 | (1) |
McSPI3_CS1(mode=1) GPIO_134(mode=4) |
||
| 15 | MMC2_DAT1 | MMC2_DAT1 | (1) | GPIO_133(mode=4) | ||
| 17 | MMC2_DAT0 | MMC2_DAT0 | (1) |
McSPI3_SOMI(mode=1) GPIO_132(mode=4) |
| |
| 19 | MMC2_CMD | MMC2_CMD | Control Wire for bus MMC2 (Wlan) |
McSPI3_SIMO(mode=1) GPIO_131(mode=4) |
||
| 21 | MMC2_CLK0 | MMC2_CLK | Clock for MMC2 (Wlan) |
McSPI3_CLK(mode=1) GPIO_130(mode=4) |
||
| 4 | MCBSP3_DX | MCBSP3_DX | Transmitted serial Data (Bluethoot audio) |
UART2_CTS(mode=1) GPIO_140(mode=4) |
TPS65950: disable it via kernel (2) If
you don't use it.
| |
| 6 | MCBSP3_CLKX | MCBSP3_CLKX | Transmitted serial Clock (Bluethoot audio) |
UART2_TX(mode=1) GPIO_142(mode=4) |
Bluethoot: Protect Bluethoot if you don'
use it. See MMC2_DAT5 pad. TPS65950: disable it via kernel (2) If
you don't use it.
| |
| 8 | MCBSP3_FSX | MCBSP3_FSX | Transmited Frame Syncronisation (Bluethoot audio) |
UART2_RX(mode=1) GPIO_143(mode=4) |
Bluethoot: Protect Bluethoot if you don'
use it. See MMC2_DAT5 pad. TPS65950: disable it via kernel (2) If
you don't use it.
| |
| 10 | MCBSP3_DR | MCBSP3_DR | Received Serial Data (Bluethoot audio) |
UART2_RTS(mode=1) GPIO_141(mode=4) |
TPS65950: disable it via kernel (2) If
you don't use it.
| |
| 12 | MCBSP1_DX | MCBSP1_DX | Transmited serial Data (not used) |
McSPI4_SIMO(mode=1) McBSP3_DX(mode=2) GPIO_158(mode=4) |
||
| 14 | MCBSP1_CLKX | MCBSP1_CLKX |
|
McBSP3_CLKX(mode=2) GPIO_162(mode=4) |
||
| 16 | MCBSP1_FSX | MCBSP1_FSX | Transmited Frame Syncronization (not used) |
McSPI4_CS0(mode=1) McBSP3_FSX(mode=2) GPIO_161(mode=4) |
||
| 18 | MCBSP1_DR | MCBSP1_DR | Received Serial Data (not used) |
McSPI4_SOMI(mode=1) McBSP3_DR(mode=2) GPIO_159(mode=4) |
||
| 20 | MCBSP1_CLKR | MCBSP1_CLKR | Received Clock (not used) |
GPIO_156(mode=4) |
||
| 22 | MCBSP1_FSR | MCBSP1_FSR | Received frame syncronization (not used) |
GPIO_157(mode=4) |
||
| 23 | I2C2_SDA | I2C2_SDA | I2C Data |
GPIO_183(mode=4) |
Cam connector: Check RC13 and RC14 is not welded or don't use it.
| |
| 24 | I2C2_SCL | I2C2_SCL | I2C Clock |
GPIO_168(mode=4) |
||
| 25 | REGEN | - | - | |||
| 26 | nRESET | - | Read Reset Omap | - | ||
| 27 | GND | - | GND | - | ||
| 28 | GND | - | GND | - |
Under construction
