Mux configuration

From IGEP - ISEE Wiki

Revision as of 10:25, 2 February 2012 by Pau (talk | contribs)

Jump to: navigation, search

Overview

This How-To is meant to be a starting point for people to learn configure mux for IGEP devices as quickly and easily as possible. For this how-to i used Linaro Headless and Ubuntu 10.04 with Linaro Toolchain.

Mux (or multiplexer) is a Omap peripheral that can be controlled via software. Its function is connect other peripherals to some available Omap pins.

Each pin is configurable by software using its associated pad configuration register field, which is 16 bits wide:

Mux register.png


One pad configuration register field is available for each pin. Each 32-bit pad configuration register is grouped into two 16-bit pad configuration register fields. One pad configuration register provides control for two different pins. These registers can be accessed using 8, 16 and 32 bits operations.

The functional bits of a pad configuration register field are divided into the following five fields:

MUXMODE (3 bits) defines the multiplexing mode applied to the pin. A mode corresponds to the selection of the functionality mapped on the pin with six (0 to 5) possible functional modes for each pin.

PULL (2 bits) for combinational pullup/pulldown configuration:

-> PULLTYPESELECT: Pullup/pulldown selection for the pin.

-> PULLUDENABLE: Pullup/pulldown enable for the pin.

INPUTENABLE (1 bit) drives an input enable signal to the I/O CTRL.

Off mode values (5 bits) override the pin state when the OFFENABLE bit CONTROL. This feature is used for power saving management. Pins in off mode can be configured like output with HIGH or LOW value or input with wake-up detection feature. For input pins, OFFOUTENABLE and OFFOUTVALUE bits can not be configured:

->OFFENABLE: Off mode pin state override control. Set to 1 to enable the feature and to 0 to disable it.

->OFFOUTENABLE: Off mode output enable value. Set to 0 to enable the feature and to 1 to disable it.

->OFFOUTVALUE: Off mode output value.

->OFFPULLUDENABLE: Off mode pullup/pulldown enable.

->OFFPULLTYPESELECT: Off mode pullup/pulldown selection.

Wake-up bits (2 bits):

->WAKEUPENABLE: Enable wake-up detection on input. It is also the off mode input enable value.
->WAKEUPEVENT: Wake-up event status for the pin.

Mux pad configuration diagram.png

Mode selection

MUXMODE Select Mode
0b000=0 Mode 0 (Primary mode)
0b001=1 Mode 1 (Possible mode)
0b010=2 Mode 2 (Possible mode)
0b011=3 Mode 3 (Possible mode)
0b100=4 Mode 4 (Possible mode)
0b101=5 Mode 5 (Possible mode)
0b110=6 Mode 6 (Possible mode)
0b111=7 Mode 7 (Safe Mode)


Mode 0 is the primary mode. When mode 0 is set, the function mapped to the pin corresponds to the name of the pin. In IGEP some pads don't use primary mode by default.

Mode 1 to mode 6 are possible modes for alternate functions. On each pin, some modes are used effectively for alternate functions, while other modes are unused and correspond to no functional configuration.

The safe mode (default mode 7) avoids any risk of electrical contention by configuring the pin as an input with no functional interface mapped to it. The safe mode is used mainly as the default mode for all pins containing no mandatory interface at the release of power-on reset.

Pull Selection

Note: when a pin is in output mode, pulls are automatically disable.

PULLTYPESELECT PULLUDENABLE Pin Behavior
0b0 0b0 Pull-down selected but not activated
0b0 0b1 Pull-down selected and activated if pin is NOT configured as OUTPUT
0b1 0b0 Pull-up selected but not activated
0b1 0b1 Pull-up selected and activated if pin is NOT configured as OUTPUT

Input Enable

INPUTENABLE = 0: Input Disable. Pin is configured in output only mode.

INPUTENABLE = 1: Input Enable. Pin is configured in bidirectional mode.

NOTE: For proper functioning of some peripherals INPUTENABLE must be set to 1 for pads configured to drive output clocks: SDRC, GPMC, McSPIi, I2Ci, MMCi, McBSPi, HSUSB HOST.

Off mode values and Wake-up

This mode is used to disable some pins and reduce power consumption.

Please contribute.

More information about mux.

Available peripherals on external connector

Use the next tables to change mux configuration as you need. First column shows all avaliable peripherals and first row shows all avaliable connectors. There are some connectors than have more peripherals, but they don't have all pads avaliable to use it. For example: MMC3 in J990.

Important tips

Use the following tips to configure mux without problems:

  • Mux can connect multiple connectors at the same peripheral, this improper use can damage the processor. Make sure to disable old connector configuration before use new one.
  • Some peripherals are only available if you place or replace some resistances. View schematics for more information.
  • Some connectors share multiples peripherals. You should disable unused peripherals to avoid interferences.  For example: if you want to control WIFI module via J990 disable OMAP or if you want use UART2 at j990 disable Bluetooth.

Configure mux

IgepV2 Board has a default mux configuration, but some cases are necessary change it, for example your project needs UART2 at j990 connector to transmit data. Mux options are vast. There are three ways to configure mux at DM37xx and OMAP35xx:

  • Editing OS User Space. this mode has a issue, when your system reboot or shutdown you will need to configure again. Example.
  • Using kernel buddies. This way is not avaliable in some cases. Example. Buddies examples.
  • Editing and compile kernel sources. Example.

IGEPv2


J990 J960 J970 J400 JC30 JA42 JA41 TP
UART1 No Yes: disable RS485 No No No No No No
UART2 Yes: disable BT

Yes: via hardware,

disable BT

No No No No No No
UART3 No Yes: default No No No No No No
UART4 No No No No No No No No
GPIO Yes: not default
No No Yes: not default Yes: default Yes: not default Yes: not default
Yes
McSPI1 No
No No No No Yes: default
No No
McSPI2 No
No No No No No No No
McSPI3

Yes: dissable WIFI

No No No No No No No
McSPI4 Yes: disable McBSP1
No No No No No No No
McBSP1 Yes: default No No No No No No No
McBSP2 No No No No No No No No
McBSP3 Yes: BT audio No No No No No No No
McBSP4 No No No No No Yes: default
No No
McBSP5 No No No No No No No No
MMC1 No No No No No No No No
MMC2 Yes: WIFI No No No No No No No
MMC3 No No No No No No No No
I2C1 No No No No No No No No
I2C2 Yes: default No No No Yes: via hardware
No No No
I2C3 No No No No No No Yes: shared with DVI
No
I2C4 No No No No No No No No


Under construction