Difference between revisions of "User:Pau pajuelo"
From IGEP - ISEE Wiki
m (→Overview) |
m (→How to use GPIOs (update it)) |
||
Line 243: | Line 243: | ||
At any point, if you see a mistake you can contribute to this How-To. | At any point, if you see a mistake you can contribute to this How-To. | ||
+ | |||
+ | == Requirements == | ||
+ | |||
+ | For this How-to, i used: | ||
+ | * IGEPv2 Board | ||
+ | * GPIO example | ||
+ | |||
+ | == Example program == | ||
+ | |||
+ | Example program contains some libraries to control GPIOs, libraries can do: | ||
+ | * Export and unexport GPIOs | ||
+ | * Set GPIO direction | ||
+ | * Set GPIO value | ||
+ | * Get GPIO value | ||
+ | * Configure hardware interrupts | ||
+ | |||
+ | Example program configures a GPIO to wait a hardware interrupt. Once the GPIO value change from 0 to 1 (rising), program give you a message. This program needs a GPIO peripheral parameter, for example GPIO 157. |
Revision as of 18:22, 14 September 2012
Contents
TODO:
Update peripheral tutorials, finish gpio example program
Categorize new tutorials
Finish tutorials below
How to manage the kernel modules on Linux
How do I edit my kernel command line
Basic Software instructions
igep.ini parameters
The kernel command line syntax is name=value1. These next parameters are supported in igep.ini since IGEP-X_Loader 2.4.0-2:
[kernel]
Parameter Name | Description | Default value | Comments |
kaddress | Kernel copy address | =0x80008000 | Hex memory address |
rdaddress | Ram Disk location address | =0x81600000 | Hex memory address; disabled by default |
serial.low | Serial number (low part) | =00000001 | Numeric |
serial.high | Serial number (high part) | =00000000 | Numeric |
revision | Revision ID | =0003 | Numeric |
kImageName | Kernel, binary image name | =zImage | Kernel or binary image name |
kRdImageName | Kernel RAM Disk Image Name | - | Ram Disk image name |
MachineID | Machine ID (kernel ID) | ;IGEPv2 =2344 |
;Module =2717 ;Proton =3203 |
Mode | Boot Mode | ;Linux kernel =kernel |
;Other image (like uboot) [binary image] |
[kparams]
Parameter Name | Description | Default value | Comments |
buddy | Enable/disable expansion board support | ;IGEPv2 Expansion Board support =igep0022 |
;Berlin and Paris Expansion Board support =base0010 New York Expansion =ilms0015 |
console | Setup the kernel console parameters | =ttyO2,115200n8 | - |
earlyprintk | Enable early printk | - | - |
mem | Setup the Board Memory Configuration | =430M | - |
boot_delay | Setup the boot delay | =0 | - |
mpurate | Setup ARM Processor Speed | - | - |
loglevel | Setup the loglevel | - | - |
debug | Enable kernel debug output | - | - |
fixrtc | Fix RTC variable | - | - |
nocompcache | Configure nocompcache variable | =1 | - |
omapfb.mode | Configure frame bugger configuration | =dvi:hd720-16@50 | ;Other configuration =dvi:1280x720MR-16@60 |
vram | Configure Video RAM assigned to every frame buffer | - | - |
omapfb.vram | Configure Video RAM assigned to every frame buffer | - | - |
omapfb.debug | Configure frame buffer debug output | - | - |
omapdss.debug | Configure DSS Video debug output | - | - |
smsc911x.mac0 | Configure Board Ethernet Mac Address | =0xb2,0xb0,0x14,0xb5,0xcd,0xde | For IGEP BERLIN |
smsc911x.mac1 | Configure Board Ethernet Mac Address | =0xb2,0xb0,0x14,0xb5,0xcd,0xdf | For IGEP BERLIN (only with IGEP PROTON) |
smsc911x.mac | Configure Board Ethernet Mac Address | =0xb2,0xb0,0x14,0xb5,0xcd,0xde | For IGEPv2, IGEP PROTON, IGEP PARIS and IGEP BERLIN |
ubi.mtd | Fot UBI FS boot | - | - |
root | Configure root directory for MMC, NFS or UBI | ;For mmc memory =/dev/mmcblk0p2 rw rootwait |
;For flash memory =/dev/mtdblock2 |
nfsroot | For NFS boot | - | - |
rootfstype | For UBI FS boot | - | - |
ip | For NFS boot | - | - |
init | Assign init program | - | - |
musb_hdrc.debug | USB debug | - | - |
musb_hdrc.use_dma | USB over network | - | - |
libertas.libertas_debug | Configure libertas debug | - | - |
board.ei485 | Enable/disable RS485 | ;Enable RS485 =yes |
;Disable RS485 =no |
board.modem | Enable/disable GPRS modem | ;Enable modem (IGEPv2 Expansion) =no |
;Enable modem (IGEPv2 Expansion) =yes |
buddy.revision | Enable hardware buddy revision [A or B] | Only for base0010 =A |
Only for base0010 =B |
How to use GPIOs (update it)
Overview
This How-To is meant to be a starting point for people to learn use GPIOs for IGEP devices as quickly and easily as possible. For this how-to i used IGEP firmware Yocto
There are more ways to use GPIOs, but this one is very simple.
Feedback and Contributing
At any point, if you see a mistake you can contribute to this How-To.
Requirements
For this How-to, i used:
- IGEPv2 Board
- GPIO example
Example program
Example program contains some libraries to control GPIOs, libraries can do:
- Export and unexport GPIOs
- Set GPIO direction
- Set GPIO value
- Get GPIO value
- Configure hardware interrupts
Example program configures a GPIO to wait a hardware interrupt. Once the GPIO value change from 0 to 1 (rising), program give you a message. This program needs a GPIO peripheral parameter, for example GPIO 157.