Difference between revisions of "User:Pau pajuelo"
From IGEP - ISEE Wiki
m (→TABLE: Start developing under IGEP Technology) |
m (→TABLE: Start developing under IGEP Technology) |
||
Line 39: | Line 39: | ||
| Install Qt Creator | | Install Qt Creator | ||
|- | |- | ||
− | | style="text-align: left;" bgcolor="#E0E0E0"| Peripherals | + | | style="text-align: left;" bgcolor="#E0E0E0" rowspan="4"| Peripherals |
+ | | GPIOs | ||
+ | | rowspan="4"| UARTs | ||
+ | | rowspan="4"| SPI | ||
+ | |- | ||
+ | | RS485 | ||
+ | |- | ||
+ | | I2c | ||
+ | |- | ||
+ | | UART into J990 | ||
+ | |- | ||
+ | | style="text-align: left;" bgcolor="#E0E0E0" rowspan="6"| Development | ||
+ | | style="t | ||
+ | | style="t | ||
+ | | style="t | ||
+ | |- | ||
+ | | style="t | ||
+ | | style="t | ||
+ | | style="t | ||
+ | |- | ||
+ | | style="t | ||
+ | | style="t | ||
+ | | style="t | ||
+ | |- | ||
+ | | style="t | ||
+ | | style="t | ||
+ | | style="t | ||
+ | |- | ||
| style="t | | style="t | ||
| style="t | | style="t | ||
| style="t | | style="t | ||
|- | |- | ||
− | |||
| style="t | | style="t | ||
| style="t | | style="t |
Revision as of 12:57, 25 January 2013
Contents
TODO:
Categorize new tutorials
How to manage the kernel modules on Linux
How do I edit my kernel command line
Basic Software instructions
TABLE: Start developing under IGEP Technology
IGEP WIKI REFERENCE ARTICLES | |||
CATEGORY | BEGINNER | INTERMEDIATE | ADVANCE |
Distribution | Install IGEP Firmware into microSD card |
Install Android 4.0 | Create your custom distribution |
Install IGEP Firmware into Flash memory |
Install Linaro (Ubuntu based) | ||
IDE | Install Eclipse IDE | Develop with Qt Creator |
|
Develop with Eclipse IDE |
Instal & Develop with Codeblocks | ||
Install Qt Creator | |||
Peripherals | GPIOs | UARTs | SPI |
RS485 | |||
I2c | |||
UART into J990 | |||
Development | style="t | style="t | style="t |
style="t | style="t | style="t | |
style="t | style="t | style="t | |
style="t | style="t | style="t | |
style="t | style="t | style="t | |
style="t | style="t | style="t | |
Information | style="t | style="t | style="t |
Other | style="t | style="t | style="t |
igep.ini parameters
The kernel command line syntax is name=value1. These next parameters are supported in igep.ini since IGEP-X_Loader 2.4.0-2:
[kernel]
Parameter Name | Description | Default value | Comments |
kaddress | Kernel copy address | =0x80008000 | Hex memory address |
rdaddress | Ram Disk location address | =0x81600000 | Hex memory address; disabled by default |
serial.low | Serial number (low part) | =00000001 | Numeric |
serial.high | Serial number (high part) | =00000000 | Numeric |
revision | Revision ID | =0003 | Numeric |
kImageName | Kernel, binary image name | =zImage | Kernel or binary image name |
kRdImageName | Kernel RAM Disk Image Name | - | Ram Disk image name |
MachineID | Machine ID (kernel ID) | ;IGEPv2 =2344 |
;Module =2717 ;Proton =3203 |
Mode | Boot Mode | ;Linux kernel =kernel |
;Other image (like uboot) [binary image] |
[kparams]
Parameter Name | Description | Default value | Comments |
buddy | Enable/disable expansion board support | ;IGEPv2 Expansion Board support =igep0022 |
;Berlin and Paris Expansion Board support =base0010 New York Expansion =ilms0015 |
console | Setup the kernel console parameters | =ttyO2,115200n8 | - |
earlyprintk | Enable early printk | - | - |
mem | Setup the Board Memory Configuration | =430M | - |
boot_delay | Setup the boot delay | =0 | - |
mpurate | Setup ARM Processor Speed | - | - |
loglevel | Setup the loglevel | - | - |
debug | Enable kernel debug output | - | - |
fixrtc | Fix RTC variable | - | - |
nocompcache | Configure nocompcache variable | =1 | - |
omapfb.mode | Configure frame bugger configuration | =dvi:hd720-16@50 | ;Other configuration =dvi:1280x720MR-16@60 |
vram | Configure Video RAM assigned to every frame buffer | - | - |
omapfb.vram | Configure Video RAM assigned to every frame buffer | - | - |
omapfb.debug | Configure frame buffer debug output | - | - |
omapdss.debug | Configure DSS Video debug output | - | - |
smsc911x.mac0 | Configure Board Ethernet Mac Address | =0xb2,0xb0,0x14,0xb5,0xcd,0xde | For IGEP BERLIN |
smsc911x.mac1 | Configure Board Ethernet Mac Address | =0xb2,0xb0,0x14,0xb5,0xcd,0xdf | For IGEP BERLIN (only with IGEP PROTON) |
smsc911x.mac | Configure Board Ethernet Mac Address | =0xb2,0xb0,0x14,0xb5,0xcd,0xde | For IGEPv2, IGEP PROTON, IGEP PARIS and IGEP BERLIN |
ubi.mtd | Fot UBI FS boot | - | - |
root | Configure root directory for MMC, NFS or UBI | ;For mmc memory =/dev/mmcblk0p2 rw rootwait |
;For flash memory =/dev/mtdblock2 |
nfsroot | For NFS boot | - | - |
rootfstype | For UBI FS boot | - | - |
ip | For NFS boot | - | - |
init | Assign init program | - | - |
musb_hdrc.debug | USB debug | - | - |
musb_hdrc.use_dma | USB over network | - | - |
libertas.libertas_debug | Configure libertas debug | - | - |
board.ei485 | Enable/disable RS485 | ;Enable RS485 =yes |
;Disable RS485 =no |
board.modem | Enable/disable GPRS modem | ;Enable modem (IGEPv2 Expansion) =no |
;Enable modem (IGEPv2 Expansion) =yes |
buddy.revision | Enable hardware buddy revision [A or B] | Only for base0010 =A |
Only for base0010 =B |