Revision as of 13:05, 5 September 2012

IGEPv2 Tutorial Guides

1/3 - Getting started with IGEPv2 2/3 - What can I do with IGEPv2 3/3 - Start developing with IGEPv2 IGEPv2 Product Page IGEPv2 Hardware manual

Overview

This is the 2/3 chapter of the Getting Started with IGEPv2 Tutorial Guide.

In this second chapter, we will learn some basics tasks. Upon completion, you will be ready to continue with chapter 3/3 that explains more advanced tasks.

What can I do

You must logged in the board.

How to use serial console

Connect a serial (COM port) cable (known as the AT/Everex Cable) to the 10-pin header J960 on the board. Now you need a Null-Modem DB9 male-make serial cable. Connect the cable between the board and your PC. Open the serial on your PC using your preferred serial communications program (minicom) and configure the port as follows:

• 115200
• 8N1
• no flow control (either software or hardware)

Open the serial port and the debug shell prompt should appear.

A detailed guide on how to connect via serial debug port can be found by following this link: Using serial debug port to communicate

Handle the GPIO-LEDS

The board has two user bicolor (green/red) leds available that can be controlled. In its simplest form, you can control of LEDs from userspace. LEDs appear in /sys/class/leds/ and you can turn on and off with following commands:

$ echo 0 > /sys/class/leds/d240\:green/brightness

$ echo 1 > /sys/class/leds/d240\:red/brightness
$ echo 0 > /sys/class/leds/d240\:red/brightness

$ echo 1 > /sys/class/leds/d440\:green/brightness
$ echo 1 > /sys/class/leds/d440\:red/brightness

A detailed guide on how use GPIO-LEDS can be found by following this link: How to handle the gpio-LED

How to use UART1 (RS232)

A detailed guide on how use UARTS can be found by following this link: How to use UARTs

How to use RS-485

This How-To is meant to be a starting point for people to learn to use RS-485 port on IGEP devices as quickly and easily as possible. We use IGEP YOCTO Firmware and RS485 example which describe how to setup and write data on the RS-485 port.

A detailed guide on how use UARTS can be found by following this link: How to use RS485

Get sound in (audio in)

External Audio input devices, such as a powered microphone or the audio output of a PC or MP3 player, can be connected to the via a 3.5mm jack (Audio IN).

You can record audio in with the application arecord, for example:

$ arecord -t wav -c 2 -r 44100 -f S16_LE -v audio-in.wav

Following output is expected on console:

Recording WAVE 'audio-in.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
Plug PCM: Hardware PCM card 0 'TWL4030' device 0 subdevice 0
Its setup is:
stream       : CAPTURE
access       : RW_INTERLEAVED
format       : S16_LE
subformat    : STD
channels     : 2
rate         : 44100
exact rate   : 44100 (44100/1)
msbits       : 16
buffer_size  : 32768
period_size  : 2048
period_time  : 46439
tick_time    : 7812
tstamp_mode  : NONE
period_step  : 1
sleep_min    : 0
avail_min    : 2048
xfer_align   : 2048
start_threshold  : 1
stop_threshold   : 32768
silence_threshold: 0
silence_size : 0
boundary     : 1073741824

When ever you think you want to stop recording just press CTRL+C

Get sound out (audio out)

Connect an external output audio device to the 3.5mm jack Audio Out connector in the board, such as external stereo powered speakers.

The amplifiers for the headset output are disabled by default, so the first thing you'll do is enable these amplifiers with:

$ amixer set -D hw:0 'Headset' 0dB
$ amixer set -D hw:0 'HeadsetL Mixer AudioL2' on
$ amixer set -D hw:0 'HeadsetR Mixer AudioR2' on

Then you can easily play a *.wav sound with the application Aplay, for example:

$ aplay audio-in.wav

How to change the monitor resolution

How to use wifi

How to use bluetooth

How to test 3D acceleration

How to use the SD card

How to use the USB OTG

How to use the USB HOST

You have successfully completed this chapter of the guide.

If you have any question, don't ask to ask at the IGEP Community Forum or the IGEP Community Chat