Difference between revisions of "Using IGEP WLAN to communicate"
From IGEP - ISEE Wiki
m |
m |
||
| Line 2: | Line 2: | ||
{{Message/Information Message|title=|message= In this guide is used [[ IGEP firmware Yocto ]]}} | {{Message/Information Message|title=|message= In this guide is used [[ IGEP firmware Yocto ]]}} | ||
<section end=exclude /> | <section end=exclude /> | ||
| − | == Overview == | + | === Overview === |
If your IGEP Processor Board has '''WIFI interface''' you can connect to it without any cable. You can open a SSH session in your computer and interact with your Board from your console. Here is how to. | If your IGEP Processor Board has '''WIFI interface''' you can connect to it without any cable. You can open a SSH session in your computer and interact with your Board from your console. Here is how to. | ||
| − | == Requirements == | + | === Requirements === |
There are some requisites to follow this guide: | There are some requisites to follow this guide: | ||
| Line 14: | Line 14: | ||
*[http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html PuTTy program] | *[http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html PuTTy program] | ||
| − | == Connect to IGEP network == | + | === Connect to IGEP network === |
Follow these steps to connect to your IGEP device: | Follow these steps to connect to your IGEP device: | ||
| Line 29: | Line 29: | ||
'''<sup>Click to enlarge image</sup>''' | '''<sup>Click to enlarge image</sup>''' | ||
| − | == Connect to IGEP == | + | === Connect to IGEP === |
Follow these steps to get a remote shell prompt: | Follow these steps to get a remote shell prompt: | ||
| Line 52: | Line 52: | ||
Note that a DHCP IP address in range 192.168.6.10-192.168.6.254 should be given to your host PC. The IGEP device should have IP address 192.168.6.1. | Note that a DHCP IP address in range 192.168.6.10-192.168.6.254 should be given to your host PC. The IGEP device should have IP address 192.168.6.1. | ||
| − | == Troubleshooting == | + | === Troubleshooting === |
| − | === NFS in root filesystem === | + | ==== NFS in root filesystem ==== |
Don't use NFS in root filesystem combined with WIFI | Don't use NFS in root filesystem combined with WIFI | ||
| − | == See also == | + | === See also === |
*[[How to setup Marvell 88w8686 SDIO wifi]] | *[[How to setup Marvell 88w8686 SDIO wifi]] | ||
Revision as of 16:25, 27 August 2012
|
In this guide is used IGEP firmware Yocto |
Contents
Overview
If your IGEP Processor Board has WIFI interface you can connect to it without any cable. You can open a SSH session in your computer and interact with your Board from your console. Here is how to.
Requirements
There are some requisites to follow this guide:
- IGEP Processor Board with WIFI
- Host computer with WIFI
- PuTTy program
Connect to IGEP network
Follow these steps to connect to your IGEP device:
- Click on the Network Manager Tray icon.
- Select IGEP_<xx> network, where <xx> is different for every IGEP device, to connect.
|
|
Click to enlarge image
Connect to IGEP
Follow these steps to get a remote shell prompt:
- Open PuTTy program
- Host Name:192.168.6.1
- Port: 22
- Connection type: SSH
- Click Open, accept Security Alert and login as root user
|
|
|
|
Click to enlarge image
Note that a DHCP IP address in range 192.168.6.10-192.168.6.254 should be given to your host PC. The IGEP device should have IP address 192.168.6.1.
Troubleshooting
NFS in root filesystem
Don't use NFS in root filesystem combined with WIFI
