Latest revision as of 16:32, 7 May 2019

Summary

X-Loader, an initial program loader for Embedded boards based on OMAP processors.

Access to the latest version here and read the ISEE_Readme.txt for get the latest release information.

Why IGEP-Xloader

Some important reasons exist for using this bootloader on IGEP boards.

Security

This is one of the most important reasons why we develop this new IGEP X-loader. you will Probably know that flash devices get new bad memory blocks with normal usage that can make unusable or can damange the software residing inside the flash (ex: upgrading the software, copying a new kernel ... ), in these cases your board won't be usable anymore if you don't use a right nand filesystem that insures data integrity. Using the old schema we've 4 important partitions on flash without any protection, x-loader, u-boot, u-boot enviroment and kernel.

IGEP X-loader resolves this situation as the configuration and kernel files reside inside a jffs2 partition.

Maintenance

With the old schema 3 different software existed (x-loader, u-boot, kernel) that did exactly the same job, so you had to reconfigure the board, increasing the complexity of maintenance for the board system and provide a major bug source because we had to assure that all software was aligned with all changes. Also, from a second point of view, we did the job three times so the boot process was more complex and slow.

Easy to use

With this new approach use the software it's more easy to use, if you've the boot information stored inside a jffs2 partition you can use the linux kernel to access it directly without the use of any flash tool to modify the software (ex: using nandwrite it's to risky due to its inability to guarantee data integrity over the Nand Flash memory).

Upgrade faster and easy

Upgradint to a new kernel it's easier and faster, you only need to copy the new kernel inside the boot partition, copy your new igep.ini inside and reboot the board with all security.

Features and Limitations

Improvements & Modifications

Added malloc/free functionality.
Added mtd framework and onenand support, removed the old onenand drivers.
Added fs jffs2 support using mtd & onenand support (Read Only).
Added crc32 and zlib.
Jffs2 zlib compression support (Read Only).
Dual boot mmc & onenand with mmc highest priority.
Added Linux kernel boot directly (Support for 2.6.22 and highest version kernels)
Linux kernel supported images: vmlinuz, bzImage and zImage.
Support for loading Linux Ram disk (EXPERIMENTAL)
Added "ini" files parser.
The configuration resides in a plain txt (ini format file).
Support Windows & Linux formating ini files.
boot from mmc, onenand, or mix with mmc highest priority.
Added codeblocks project and compilation rules.
Added support for vfat32 extra names.
Configure TPS65950 voltage to 1.35V if it's used a DM3730 processor.
Added new parameter MachineID in kernel tag file, with it you can
- configure the kernel board ID setup
Added new parameter buddy for kernels 2.6.35.y and 2.6.37.y
Optimize some LPDDR Memory configuration values
Removed some OneNand Debug information
Removed some FAT incorrect warnings
Added Support Initial Ram disk
Reconfigure Makefile options
Support Kernels 2.6.35, 2.6.37, 3.6.4
Added support for boot ARM binary files (such u-boot or QNX kernel)
Support for Numonyx, Micron and hynix POP Memories.
Memory autodetection.
Added GPTimer functionality.
Support Numonyx, Micron and hynix memories.
DMA Copy support
Omtimized memcpy and memset functions.
DSS Video driver.
Support ISEE toolchain yocto 1.2 based.

Limitations

The ini configuration file it's limited to max size: 16 KiB
Kernel Command line parameters it's limited to: 4 KiB
Malloc it's hardcode limited to 32 MiB.
Video is limited to 1024 x 768 x 16 bits.
Video Memory is limited to 1280 x 720 x 32 bits.

TODO

Remove compilation warnings.
System Rescue.
Improve boot selection and priority.
Remove unused code.

STATUS

Support:
- IGEPv2 DM3730
- IGEPv2 OMAP3530
- IGEP COM MODULE DM3730
- IGEP COM PROTON DM3730
- IGEP COM MODULE AM3703

VERSION CHANGES

[2.1.0-1] This version only can be build with gcc linaro 4.5.2 other compilers be not supported.

[2.1.0-1] Removed some uncontrolled "printf" with incorrect information.

[2.1.0-1] Modified some code under __DEBUG__ option.

[2.1.0-1] Added Support for TPS65950-A3 initialization at 1.35V

[2.1.0-1] Added support for IGEP Module 0030

[2.1.0-1] Added support dynamic Machine ID selection (same xloader boot IGEPv2 & IGEP Module)

[2.1.0-2] ARM Compilation bug resolved

[2.1.0-3] Update SDRAM structure initialization

[2.1.0-3] Added support for Initial RAM disk

[2.1.0-3] Updated Initial RAM disk destination address

[2.2.0-1] Update Makefile structure

[2.2.0-1] Downgrade the boot processor speed

[2.3.0-1] Add NAND flash devices and Micron MT29CXGXXMAXX memories support

[2.3.0-2] Add Hynix NAND memorie and IGEP0032 support

[2.3.0-2] Added lzo compression schema.

[2.3.0-3] Add Support for execute ARM binaries [2.3.0-3] Bug Fixes related to I and D Cache

[2.4.0-1] Added Memory test feature

[2.4.0-1] Added some boot information

[2.4.0-1] New read_nand_cache function optimized for load from NAND

[2.4.0-1] BUG resolved: Refresh Setup in Micron & Hynix Memories

[2.4.0-1] BUG resolved: Reset Memory controller after initialize Malloc function

[2.4.0-1] BUG resolved: Resolve problems updating the flash content under jffs2

[2.4.0-2] Resolved Memory Autodetection

[2.4.0-2] Better hang board led control

[2.4.0-2] New read_nand_cache function optimized for load from OneNand

[2.4.0-2] Added Hw GPtimer functionality

[2.5.0-1] Added System DMA driver.

[2.5.0-1] Added optimized memcpy & memset functions.

[2.5.0-1] Improved boot speed.

[2.5.0-1] Improve NAND driver support.

[2.5.0-1] Auto x-loader.bin.ift and MLO generation.

[2.5.0-1] Added DSS video support.

[2.5.0-2] Fixed System DMA misconfiguration.

[2.5.0-2] Improve GPMC timming setup.

[2.5.0-2] Added DSS igep.ini variables.

[2.5.0-2] Added Support for new memory capacities.

[2.5.0-2] Auto x-loader.bin.ift and MLO generation.

[2.5.0-2] Minor bug fixes.

[2.5.0-3] platform.S: downgrade MPU boot clock from 1GHz to 800 MHz

[2.6.0-1] Remove OMAP35xx support

[2.6.0-1] New DMA driver, now can handle different DMA channels and transfers

[2.6.0-1] GPMC: Add support for use prefetch engine

[2.6.0-1] NAND: Added a new Nand driver

[2.6.0-1] NAND: Modify memory setup timmings

[2.6.0-2] DMA: disable dma_memcpy function due random kernel memory corruption

Pre-Compiled Binaries

Release	Download link	Support
2.6.0-2	igep-x-loader-2.6.0-2.tar.bz2	DM3730 Boards
2.5.0-2	igep-x-loader-2.5.0-2.tar.bz2	All OMAP3 Boards
2.4.0-2	igep-x-loader-2.4.0-2.tar.bz2	All OMAP3 Boards except IGEP COM MODULE AM3703
2.1.0-2	igep-x-loader-2.1.0-2.tar.bz2	All OMAP3 Boards except IGEP COM MODULE AM3703
2.1.0-3	igep-x-loader-2.1.0-3.tar.bz2	All OMAP3 Boards except IGEP COM MODULE AM3703
2.2.0-1	igep-x-loader-2.2.0-1.tar.bz2	All OMAP3 Boards except IGEP COM MODULE AM3703

Build Procedure

Build with ISEE SDK Yocto Toolchain 1.2

Download and Install the cross compiler if you not do it before.

Download the toolchain from this link and uncompress it as root in your / directory.

Hint: Remember setup the enviroment before build the source:

source /opt/poky/1.2/environment-setup-armv7a-vfp-neon-poky-linux-gnueabi

Download the sources from our git repository

git clone git://git.isee.biz/pub/scm/igep-x-loader.git

Get your desired tag / release

git checkout <your_desired_release> -b <your_name_release>

git checkout release-2.5.0-2 -b release-2.5.0-2-local

Setup the board build setup

make igep00x0_config

Build the software

make

Sign the binary x-loader (Only versions prior to 2.5.0-x)

You should execute contrib/signGP for sign the xloader.

contrib/signGP x-load.bin
The signed x-loader it's named: x-load.bin.ift

Build Native

Download from git repository

git clone https://git.isee.biz/arm-boot/igep-x-loader.git

git checkout <your_desired_release> -b <your_name_release>

 git checkout release-2.5.0-2 -b release-2.5.0-2-local

Configure the board settings

make igep00x0_config

Edit the variable CFLAGS and add the option: -fno-stack-protector
CFLAGS := $(CPPFLAGS) -Wall -Wstrict-prototypes -fno-stack-protector

Build

make CROSS_COMPILE=arm-none-linux-gnueabi-

Sign the binary x-loader

You should execute contrib/signGP for sign the xloader.

contrib/signGP x-load.bin
The signed x-loader it's named: x-load.bin.ift

BOOT

The IGEP X-Loader must reside in the microSD card or in the Nand Memory.

MMC Boot

Prepare the microsd card

You can follow this howto about how prepare the microsd card or How to boot from MicroSD Card

Get a new microsd card and create two partitions, the first one must be fat16/32 and the second one can be formated in any format type supported by linux kernel.

Copy the files in the first (FAT) partition

In the first partition you must copy in this order:

x-loader.bin.ift (you must rename this file to MLO before copy it) / This is a signed image using contrib/signGP tool
x-loader configuration file igep.ini also you can change the configuration file name editing the file: igep00x0.h (#define IGEP_BOOT_CFG_INI_FILE "igep.ini")
Your desired kernel image.

Load Order:

  48 /* Linux Images */
  49 const char* LinuxImageNames [] = {
  50         "kparam"   /* Use kparam first */
  51         "zImage",   /* jffs2 it's case sensitive */
  52         "zimage",   /* fat name it's not case sentitive */
  53         "vmlinuz",
  54         "bzImage",
  55         "bzimage",
  56         0,
  57 };

or you can set the name for your kernel in the configuration file using the tag: kImageName

Don't use a uImage kernel format (from uboot), only standard kernel formats be supported.

kernel build command example:

make ARCH=arm CROSS_COMPILE=arm-poky-linux-gnueabi- zImage modules

Second Partition

Copy all your rootfs in this second partition.

Also you can use the linaro 10.11 minimal image download the image and untar (as root) in your microsd card second partition.

Remember install the kernel modules in this partition.

Example:

sudo make ARCH=arm CROSS_COMPILE=arm-poky-linux-gnueabi- modules_install INSTALL_MOD_PATH=[path to your target rootfs]

Nand Boot

Nand Partitions

We've defined 3 partitions on the Nand Memory.

MTD partitions on "omap2-onenand":
(a) 0x000000000000-0x000000080000 : "X-Loader"
(b) 0x000000080000-0x000000c80000 : "Boot"
(c) 0x000000c80000-0x000020000000 : "File System"

X-Loader Partition

Not fs formated (onenand raw)
Size: 0x80000 (512 KiB)
The xloader must be signed before copy it into the flash memory.

You should copy the x-loader in the firsts 4 blocks (first 512 KiB), this is not a formated partition due the ROM not permits boot from a formated partition in flash, you should use flash_eraseall and writeloader for copy x-loader in the first blocks.

Suggested procedure:

Sign the x-loader before write it on the flash or microsd card.
Sign x-loader:
You should execute contrib/signGP for sign the xloader that resides inside the flash memory.
contrib/signGP x-load.bin
The signed x-loader it's named: x-load.bin.ift

Erase and copy the x-loader into the first flash partition (mtd0):
flash_eraseall /dev/mtd0
writeloader -i <x-loader.bin.ift> -o /dev/mtd0

Boot Partition

filesystem used jffs2 zlib/lzo compressed filesystem.
Suggested size: 0xC00000 (12 MiB).

X-Loader only support jffs2 partitions for boot partition.

Create the boot partition:

Suggested procedure:

Erase all mtd1 content:
flash_eraseall /dev/mtd1

Create your partition:
mount -t jffs2 /dev/mtdblock1 /mnt

Next uses:

You can mount the partition over your boot directory in the rootfs

mount -t jffs2 /dev/mtdblock1 /boot

You can use the cp command for copy your kernel and igep.ini configuration file.

cp igep.ini /boot
cp zImage /boot

Rootfs Partition

fs (your prefered fs supported by linux, maybe a good choice it should be ubifs)
Size, all or you can create more partitions if you wish ...

Boot Priority

XLoader first try load from mmc and if it fails then try from OneNand.

MLO (x-loader), igep.ini, zImage from MMC
If all it's present in the mmc it don't try to boot from Onenand.

MLO (x-loader) in MMC, igep.ini and zImage in Onenand.
If only MLO it's provided this one try to load the other information from the Onenand.

It means that XLoader always try to load the information from MMC and if it fails then try to load from OneNand.

Configuration file: igep.ini

This entry in wikipedia can help you how a ini file it's structured.

Inside the sources/scripts directory you can found a igep.ini example file.

The actual XLoader can handle two kind tags:

[kernel] Used for internal XLoader setup.

[kparams] Used for pass the linux kernel parameters.

TAG: [kernel]

   1 [kernel]
   2 kaddress=0x80008000
   3 rdaddress=0x81600000
   4 serial.low=00000001
   5 serial.high=00000000
   6 revision=0001
   7 kImageName=zImage-test
   8 kRdImageName=rdImage-test
   9 MachineID=xxxx Where Machine ID = 2344 for IGEPv2,  ID = 2717 for IGEP COM Module, ID = 3203 for IGEP COM PROTON   
   10 Mode=<kernel> or <binary>
   11 dss=<0 or 1> Enable or Disable Video Output
   12 dss_color=<0x00FF8000> Write your desired color in hex value
   13 dss_bitmap=<filename> Raw display image

Parameter Name	Description	Default Value	Comments
kaddress	Kernel copy address	0x80008000	hex memory address
rdaddress	Ram Disk location address	0x81600000	hex memory address
serial.low	Serial number (low part)	0 - 99999999	numeric
serial.high	Serial number (high part)	0 - 99999999	numeric
revision	Revision ID	0 - 9999	numeric
kImageName	Kernel, binary image name	N/A	Kernel or binary image name
kRdImageName	Ramdisk	N/A	Ram Disk image name
MachineID	Machine ID (kernel ID)	2717	2717 (IGEP COM Module) \| 2344 IGEPv2 \| 3203 (IGEP COM PROTON)
Mode	Boot Mode	kernel	kernel=linux kernel / binary=boot binary image
dss	Enable Video	0	0 = Disable, 1 Enable Video Output
dss_color	Video Color	0x00FF8000	Solid Color
dss_bitmap	Video Bitmap Image	string	filename with desired image

TAG: [kparams]

In this tag you can add all kernel parameters that you need, this is only an example:

  10 [kparams]
  11 console=ttyS2,115200n8
  12 ;earlyprintk=serial,ttyS2,115200
  13 mem=512M
  14 boot_delay=0
  15 ;mpurate=800
  16 ;loglevel=7
  17 omapfb.mode=dvi:1024x768MR-16@60\r
  18 smsc911x.mac=0xb2,0xb0,0x14,0xb5,0xcd,0xde\r
  19 ;ubi.mtd=2
  20 ;root=ubi0:igep0020-rootfs
  21 ;rootfstype=ubifs
  22 root=/dev/mmcblk0p2 rw rootwait

Also remember you can comment any line using ';' or '#' characters.

FAQ

How I can boot from NFS?

Yes, you should add below parameters in the kparams tag:

#smsc911x.mac fix your mac address
smsc911x.mac=0xb2,0xb0,0x14,0xb5,0xcd,0xde
# IP set you IP settings <local_ip>:<server_ip>:<gateway>:<network_mask>::<interface>:
ip=192.168.2.123:192.168.2.105:192.168.2.1:255.255.255.0::eth0:
# Set root as nfs
root=/dev/nfs
# Set your NFS root path as <server_ip>:<rootfs_path>
nfsroot=192.168.2.105:/srv/nfs/linaro_minimal

How I can change the assigned kernel memory?

You can use the mem kernel variable as assign your desired kernel memory as:

[kparams]
mem=430M

How I can add more kernel variables?

You can add more variables creating a new variable - value pair under kparams tag as:

boot_delay=0

How I can modify my MAC address?

You can assign your desired mac address using the variable smsc911x.mac as:

smsc911x.mac=0xb2,0xb0,0x14,0xb5,0xcd,0xde

How I can boot my board using ubi root filesystem?

You should use these parameters:

ubi.mtd=2

root=ubi0:igep0020-rootfs

rootfstype=ubifs

How I can boot my board using a RAM disk?

Use a RAMdisk it's fully supported.

[kernel]
rdaddress=0x81600000
kRdImageName=ramdisk.bin

[kparams]
root=/dev/ram0 rw

Can I change the Processor frecuency?

Yes you can, IGEP X-loader configures the processor to boot at 600 Mhz you can select a different boot speed using the variable mpurate as:

mpurate=800

If you don't force any frequency the linux kernel will put your processor at the maximum speed (ex: DM3730 will run at 1 Ghz)

How I can boot downloading the kernel using wget?

The way for do that it's using one minimal kernel and RAMdisk (ex: using image-core-minimal from poky), the procedure can be more or less:

a) Copy your minimal kernel and your Ramdisk inside the boot partition.

b) Boot Normally from this kernel and Ramdisk, create one script your your desired command such wget http://192.168.15.22/mykernel.bin

c) Execute the script when boot (you can do that adding the script to the init enviroment)

d) if the downloading it's ok then execute the kexec call, first load the kernel and then pass to it your desired parameters.

e) finally boot the new kernel with kexec.

My board not boot and I don't know what to do ...

When you test your IGEP X-loader, igep.ini file and kernel we suggest use a microsd card in front of use directly the flash nand, if your flash not boot copy all files in one microsd card and boot from there. You can check what happens removing some files from your microsd card for example if you wish test if your flashed kernel it's loaded in a right way then remove the kernel from your microsd card (note: use the same kernel name), IGEP X-loader first try load the file from your microsd card but if it's not found then it try to find the file in the flash.

How I can upgrade my old kernel?

Just copy the new one, the most secure way it's copy the new one and at end replace the igep.ini file with your new one.

 mount -t jffs2 /dev/mtdblock1 /boot

 cp newkernel.bin /boot

 cp igep.ini /boot

Use a different kernel name and you always can boot from your old one.

6 Contribution & Support & Bugs Report

Contributions to this project be welcome and you can send your patches to support@iseebcn.com or you can use the igep forum for it.
You can access to IGEP-x-Loader repository using our git at git.isee.biz
IGEP IRC Channel: http://webchat.freenode.net/?channels=igep

If you have any question, don't ask to ask at the IGEP Community Forum or the IGEP Community Chat

@@ Line 1: / Line 1: @@
-= Summary<br><br>  =
+=Summary=
+X-Loader, an initial program loader for Embedded boards based on OMAP processors.
-X-Loader, an initial program loader for Embedded boards based on OMAP processors. <br>
+Access to the latest version&nbsp;[http://git.isee.biz/?p=pub/scm/igep-x-loader.git;a=summary here] and read the [http://git.isee.biz/?p=pub/scm/igep-x-loader.git;a=blob_plain;f=ISEE_README.txt;h=909c072bc2512026342d802b3ef1b7e8f703458b;hb=4bb2ebd99d5b86522d786ac5b074066e9841799c ISEE_Readme.txt] for get the latest release information.
-= Features and Limitations<br>  =
+=Why IGEP-Xloader=
+Some important reasons exist for using this bootloader on IGEP boards.
-== Improvements &amp; Modifications<br>  ==
+==Security==
+This is one of the most important reasons why we develop this new IGEP X-loader. you will Probably know that flash devices get new bad memory blocks with normal usage that can make unusable or can damange the software residing inside the flash (ex: upgrading the software, copying a new kernel ... ), in these cases your board won't be usable anymore if you don't use a right nand filesystem that insures data integrity. Using the old schema we've 4 important partitions on flash without any protection, x-loader, u-boot, u-boot enviroment and kernel.
-*Malloc/free functionality.
+IGEP X-loader resolves this situation as the configuration and kernel files reside inside a jffs2 partition.
-*Mtd framework and onenand support, removed the old onenand drivers.
-*Jffs2 support using mtd &amp; onenand support (Read Only).
-*Crc32 and zlib.
-*Jffs2 zlib compression support (Read Only).
-*Dual boot mmc &amp; onenand with mmc highest priority.
-*Linux kernel boot directly (Support for 2.6.22 and highest version kernels)
-*Linux kernel supported images: vmlinuz, bzImage and zImage.
-*Support for loading Linux Ram disk (EXPERIMENTAL)
-*"ini" files parser.
-*The configuration resides in a plain txt (ini format file).
-*Support Windows &amp; Linux formating ini files.
-*Boot from mmc, onenand, or mix with mmc highest priority.
-*Codeblocks project and compilation rules.
-*Support for gcc 4.5.1.<br>
-== Limitations<br>  ==
+==Maintenance==
+With the old schema 3 different software existed (x-loader, u-boot, kernel) that did exactly the same job, so you had to reconfigure the board, increasing the complexity of maintenance for the board system and provide a major bug source because we had to assure that all software was aligned with all changes. Also, from a second point of view, we did the job three times so the boot process was more complex and slow.
-*The ini configuration file it's limited to max size: 16 KiB
+==Easy to use==
-*Kernel Command line parameters it's limited to: 4 KiB
+With this new approach use the software it's more easy to use, if you've the boot information stored inside a jffs2 partition you can use the linux kernel to access it directly without the use of any flash tool to modify the software (ex: using nandwrite it's to risky due to its inability to guarantee data integrity over the Nand Flash memory).
-*Malloc it's limited to 32 MiB.
-*Cannot write comments in lines with tag=value<br>
-== TODO<br>  ==
+==Upgrade faster and easy==
+Upgradint to a new kernel it's easier and faster, you only need to copy the new kernel inside the boot partition, copy your new igep.ini inside and reboot the board with all security.
-*Support for IGEP0030 - Family boards.
+=Features and Limitations=
-*Support for other OMAP/DM/AM processor boards.
+==Improvements &amp; Modifications==
-*Remove compilation warnings.
+* Added malloc/free functionality.
-*Comments in tag lines<br>
+* Added mtd framework and onenand support, removed the old onenand drivers.
+* Added fs jffs2 support using mtd &amp; onenand support (Read Only).
+* Added crc32 and zlib.
+* Jffs2 zlib compression support (Read Only).
+* Dual boot mmc &amp; onenand with mmc highest priority.
+* Added Linux kernel boot directly (Support for 2.6.22 and highest version kernels)
+* Linux kernel supported images: vmlinuz, bzImage and zImage.
+* Support for loading Linux Ram disk (EXPERIMENTAL)
+* Added "ini" files parser.
+* The configuration resides in a plain txt (ini format file).
+* Support Windows &amp; Linux formating ini files.
+* boot from mmc, onenand, or mix with mmc highest priority.
+* Added codeblocks project and compilation rules.
+* Added support for vfat32 extra names.
+* Configure TPS65950 voltage to 1.35V if it's used a DM3730 processor.
+* Added new parameter MachineID in kernel tag file, with it you can
+* &nbsp;&nbsp;&nbsp; - configure the kernel board ID setup
+* Added new parameter buddy for kernels 2.6.35.y and 2.6.37.y
+* Optimize some LPDDR Memory configuration values
+* Removed some OneNand Debug information
+* Removed some FAT incorrect warnings
+* Added Support Initial Ram disk
+* Reconfigure Makefile options
+* Support Kernels 2.6.35, 2.6.37, 3.6.4
+* Added support for boot ARM binary files (such u-boot or QNX kernel)
+* Support for Numonyx, Micron and hynix POP Memories.
+* Memory autodetection.
+* Added GPTimer functionality.
+* Support Numonyx, Micron and hynix memories.
+* DMA Copy support
+* Omtimized memcpy and memset functions.
+* DSS Video driver.
+* Support ISEE toolchain yocto 1.2 based.
-== STATUS<br>  ==
+==Limitations==
+* The ini configuration file it's limited to max size: 16 KiB
+* Kernel Command line parameters it's limited to: 4 KiB
+* Malloc it's hardcode limited to 32 MiB.
+* Video is limited to 1024 x 768 x 16 bits.
+* Video Memory is limited to 1280 x 720 x 32 bits.
-*Support IGEP0020 Revision B &amp; C family boards.
+==TODO==
-*Tested with IGEPv2 (DM3730@1Ghz and 512/512 MB Ram/Onenand)
+* Remove compilation warnings.
-*Tested with IGEPv2 (AM3703@1Ghz and 512/512 MB Ram/Onenand)
+* System Rescue.
-*Tested with IGEPv2 (OMAP3530@720Mhz and 512/512 MB Ram/Onenand)<br>
+* Improve boot selection and priority.
+* Remove unused code.
-= Build Procedure<br>  =
+==STATUS==
+* Support:
+** IGEPv2 DM3730
+** IGEPv2 OMAP3530
+** IGEP COM MODULE DM3730
+** IGEP COM PROTON DM3730
+** IGEP COM MODULE AM3703
-== Build with Ubuntu Cross Compiler gcc 4.5.1  ==
+==VERSION CHANGES==
+[2.1.0-1] This version only can be build with gcc linaro 4.5.2 other compilers be not supported.
-<span style="font-style: italic;"><span style="font-weight: bold;">Enviroment</span></span>'''''Ubuntu 10.10'''''
+[2.1.0-1] Removed some uncontrolled "printf" with incorrect information.
-=== Install the cross compiler if you not do it before.<br>  ===
+[2.1.0-1] Modified some code under __DEBUG__ option.
-<pre>apt-get install cpp-4.5-arm-linux-gnueabi g++-4.5-arm-linux-gnueabi</pre>
-=== Setup the board settings<br>  ===
-<pre>make igep0020-sdcard_config</pre>
-=== Build<br>  ===
-<pre>make</pre>
-=== Sign the binary x-loader<br>  ===
-''You should execute contrib/signGP for sign the xloader.''
+[2.1.0-1] Added Support for TPS65950-A3 initialization at 1.35V
-<pre>contrib/signGP x-load.bin
-The signed x-loader it's named: x-load.bin.ift
-</pre>
-== Build with IGEP SDK  ==
-=== Setup the Enviroment<br>  ===
+[2.1.0-1] Added support for IGEP Module 0030
-<pre>source /usr/local/poky/eabi-glibc/environment-setup-arm-none-linux-gnueabi
-</pre>
-=== Setup the board settings<br>  ===
-<pre>make igep0020-sdcard_config</pre>
-=== Build<br>  ===
-<pre>make CROSS_COMPILE=arm-none-linux-gnueabi-</pre>
-=== Sign the binary x-loader  ===
-''You should execute contrib/signGP for sign the xloader.''
+[2.1.0-1] Added support dynamic Machine ID selection (same xloader boot IGEPv2 &amp; IGEP Module)
-<pre>contrib/signGP x-load.bin
-The signed x-loader it's named: x-load.bin.ift
-</pre>
-== Build Native  ==
-=== Configure the board settings<br>  ===
+----
-<pre>make igep0020-sdcard_config
-</pre><pre>Edit the variable CFLAGS and add the option: -fno-stack-protector
-CFLAGS&nbsp;:= $(CPPFLAGS) -Wall -Wstrict-prototypes -fno-stack-protector</pre>
-=== Build<br>  ===
-<pre>make CROSS_COMPILE=arm-none-linux-gnueabi-</pre>
-=== Sign the binary x-loader  ===
-''You should execute contrib/signGP for sign the xloader.''
+[2.1.0-2] ARM Compilation bug resolved
-<pre>contrib/signGP x-load.bin
-The signed x-loader it's named: x-load.bin.ift
-</pre>
-= BOOT<br>  =
-The IGEP X-Loader must reside in the microSD card or in the OneNand.<br>
+----
-== Low Level Initialization  ==
+[2.1.0-3] Update SDRAM structure initialization
-The OMAP Processor loads the XLoader directly from the mmc or the OneNand and copy the binary into the internal processor RAM (0x40200000) and jump to this place, this internal memory it's limited to 64K divided as: Interrupts, code, data and stack. Initialization code can be found using this link: [http://git.igep.es/?p=pub/scm/igep-x-loader.git;a=blob;f=cpu/omap3/start.S;h=4cbf4379b8502ebfe0409b35e4aafba712234c34;hb=HEAD start.S]&nbsp;
+[2.1.0-3] Added support for Initial RAM disk
-<pre>&nbsp; 96 reset:
-         /*
-          * set the cpu to SVC32 mode
+[2.1.0-3] Updated Initial RAM disk destination address
-          */
+----
-         mrs     r0,cpsr
+[2.2.0-1] Update Makefile structure
-         bic     r0,r0,#0x1f
+[2.2.0-1] Downgrade the boot processor speed
-         orr     r0,r0,#0xd3
+----
-         msr     cpsr,r0
+[2.3.0-1] Add NAND flash devices and Micron MT29CXGXXMAXX memories support
+[2.3.0-2] Add Hynix NAND memorie and IGEP0032 support
-         /* Copy vectors to mask ROM indirect addr */
+[2.3.0-2] Added lzo compression schema.
-         adr     r0, _start              /* r0 &lt;- current position of code   */
+----
-         add     r0, r0, #4                              /* skip reset vector                    */
+[2.3.0-3] Add Support for execute ARM binaries [2.3.0-3] Bug Fixes related to I and D Cache
-         mov     r2, #64                 /* r2 &lt;- size to copy  */
+----
-         add     r2, r0, r2              /* r2 &lt;- source end address         */
+[2.4.0-1] Added Memory test feature
-         mov     r1, #SRAM_OFFSET0         /* build vect addr */
+[2.4.0-1] Added some boot information
-         mov     r3, #SRAM_OFFSET1
+[2.4.0-1] New read_nand_cache function optimized for load from NAND
-         add     r1, r1, r3
+[2.4.0-1] BUG resolved: Refresh Setup in Micron &amp; Hynix Memories
-         mov     r3, #SRAM_OFFSET2
+[2.4.0-1] BUG resolved: Reset Memory controller after initialize Malloc function
-         add     r1, r1, r3
+[2.4.0-1] BUG resolved: Resolve problems updating the flash content under jffs2
-next:
+----
-         ldmia   r0!, {r3-r10}           /* copy from source address [r0]    */
+[2.4.0-2] Resolved Memory Autodetection
-         stmia   r1!, {r3-r10}           /* copy to   target address [r1]    */
+[2.4.0-2] Better hang board led control
-         cmp     r0, r2                  /* until source end address [r2]    */
+[2.4.0-2] New read_nand_cache function optimized for load from OneNand
-         bne     next                    /* loop until equal */
+[2.4.0-2] Added Hw GPtimer functionality
+----
-         bl      cpy_clk_code            /* put dpll adjust code behind vectors */
+[2.5.0-1] Added System DMA driver.
+[2.5.0-1] Added optimized memcpy &amp; memset functions.
-         /* the mask ROM code should have PLL and others stable */
+[2.5.0-1] Improved boot speed.
-         bl cpu_init_crit
+[2.5.0-1] Improve NAND driver support.
-&nbsp;125
+[2.5.0-1] Auto x-loader.bin.ift and MLO generation.
-relocate:                               /* relocate U-Boot to RAM           */
+[2.5.0-1] Added DSS video support.
-         adr     r0, _start              /* r0 &lt;- current position of code   */
+----
-         ldr     r1, _TEXT_BASE          /* test if we run from flash or RAM */
+[2.5.0-2] Fixed System DMA misconfiguration.
-         cmp r0, r1                      /* no need to relocate if XIP       */
+[2.5.0-2] Improve GPMC timming setup.
-         beq stack_setup                 /* skip txt cpy if XIP(SRAM, SDRAM) */
+[2.5.0-2] Added DSS igep.ini variables.
+[2.5.0-2] Added Support for new memory capacities.
-         ldr     r2, _armboot_start
+[2.5.0-2] Auto x-loader.bin.ift and MLO generation.
-         ldr     r3, _bss_start
+[2.5.0-2] Minor bug fixes.
-         sub     r2, r3, r2              /* r2 &lt;- size of armboot            */
+----
-         add     r2, r0, r2              /* r2 &lt;- source end address         */
+[2.5.0-3] platform.S: downgrade MPU boot clock from 1GHz to 800 MHz
+----
-copy_loop:
+[2.6.0-1] Remove OMAP35xx support
-         ldmia   r0!, {r3-r10}           /* copy from source address [r0]    */
+[2.6.0-1] New DMA driver, now can handle different DMA channels and transfers
-         stmia   r1!, {r3-r10}           /* copy to   target address [r1]    */
+[2.6.0-1] GPMC: Add support for use prefetch engine
-         cmp     r0, r2                  /* until source end addreee [r2]    */
+[2.6.0-1] NAND: Added a new Nand driver
-         ble     copy_loop
+[2.6.0-1] NAND: Modify memory setup timmings
+----
-         /* Set up the stack                                                 */
+[2.6.0-2] DMA: disable dma_memcpy function due random kernel memory corruption
-stack_setup:
+=Pre-Compiled Binaries=
+{| border="1" width="905" cellspacing="1" cellpadding="1"
+|-
+! scope="col"|Release
+! scope="col"|Download link
+! scope="col"|Support
+|-
+||2.6.0-2
+||[http://downloads.isee.biz/pub/releases/IGEP_xloader/igep-x-loader-2.6.0-2.tar.bz2 igep-x-loader-2.6.0-2.tar.bz2]
+||[[The_IGEP_X-loader#STATUS | DM3730 Boards]]
+|-
+||2.5.0-2
+||[http://downloads.isee.biz/pub/releases/IGEP_xloader/igep-x-loader-2.5.0-2.tar.bz2 igep-x-loader-2.5.0-2.tar.bz2]
+||[[The_IGEP_X-loader#STATUS | All OMAP3 Boards]]
+|-
+||2.4.0-2
+||[http://downloads.isee.biz/pub/releases/IGEP_xloader/igep-x-loader-2.4.0-2.tar.bz2 igep-x-loader-2.4.0-2.tar.bz2]
+||[[The_IGEP_X-loader#STATUS | All OMAP3 Boards]] except IGEP COM MODULE AM3703
+|-
+||2.1.0-2
+||[http://downloads.isee.biz/pub/releases/IGEP_xloader/igep-x-loader-2.1.0-2.tar.bz2 igep-x-loader-2.1.0-2.tar.bz2]
+||[[The_IGEP_X-loader#STATUS | All OMAP3 Boards]] except IGEP COM MODULE AM3703
+|-
+||2.1.0-3
+||[http://downloads.isee.biz/pub/releases/IGEP_xloader/igep-x-loader-2.1.0-3.tar.bz2 igep-x-loader-2.1.0-3.tar.bz2]
+||[[The_IGEP_X-loader#STATUS | All OMAP3 Boards]] except IGEP COM MODULE AM3703
+|-
+||2.2.0-1
+||[http://downloads.isee.biz/pub/releases/IGEP_xloader/igep-x-loader-2.2.0-1.tar.bz2 igep-x-loader-2.2.0-1.tar.bz2]
+||[[The_IGEP_X-loader#STATUS | All OMAP3 Boards]] except IGEP COM MODULE AM3703
+|}
-         ldr     r0, _TEXT_BASE          /* upper 128 KiB: relocated uboot   */
+=Build Procedure=
+==Build with ISEE SDK Yocto Toolchain 1.2==
+===Download and Install the cross compiler if you not do it before.===
+Download the toolchain from this [https://www.isee.biz/support/downloads/item/igep-sdk-yocto-toolchain-1-2-2-3 link] and uncompress it as root in your / directory.
-         sub     sp, r0, #128            /* leave 32 words for abort-stack   */
+<pre>Hint: Remember setup the enviroment before build the source:
-         and     sp, sp, #~7             /* 8 byte alinged for (ldr/str)d    */
+source /opt/poky/1.2/environment-setup-armv7a-vfp-neon-poky-linux-gnueabi</pre>
+===Download the sources from our git repository===
+<pre>git clone git://git.isee.biz/pub/scm/igep-x-loader.git
+</pre>
+===Get your desired tag / release===
+git checkout &lt;your_desired_release&gt; -b &lt;your_name_release&gt;
-         /* Clear BSS (if any).  Is below tx (watch load addr - need space)  */
+<pre>git checkout release-2.5.0-2 -b release-2.5.0-2-local
+</pre>
-clear_bss:
+===Setup the board build setup===
+<pre>make igep00x0_config</pre>
+===Build the software===
+<pre>make</pre>
+===Sign the binary x-loader (Only versions prior to 2.5.0-x)===
+''You should execute contrib/signGP for sign the xloader.''
-         ldr     r0, _bss_start          /* find start of bss segment        */
+<pre>contrib/signGP x-load.bin
+The signed x-loader it's named: x-load.bin.ift
+</pre>
-         ldr     r1, _bss_end            /* stop here                        */
+==Build Native==
+===Download from git repository===
+  git clone https://git.isee.biz/arm-boot/igep-x-loader.git
+git checkout &lt;your_desired_release&gt; -b &lt;your_name_release&gt;
-         mov     r2, #0x00000000         /* clear value                      */
+<pre style="font-weight: normal;"> git checkout release-2.5.0-2 -b release-2.5.0-2-local
+</pre>
-clbss_l:
+===Configure the board settings===
+<pre>make igep00x0_config</pre>
+<pre>Edit the variable CFLAGS and add the option: -fno-stack-protector
+CFLAGS&nbsp;:= $(CPPFLAGS) -Wall -Wstrict-prototypes -fno-stack-protector</pre>
+===Build===
+<pre>make CROSS_COMPILE=arm-none-linux-gnueabi-</pre>
+===Sign the binary x-loader===
+''You should execute contrib/signGP for sign the xloader.''
-         str     r2, [r0]                /* clear BSS location               */
+<pre>contrib/signGP x-load.bin
+The signed x-loader it's named: x-load.bin.ift
+</pre>
+=BOOT=
+The IGEP X-Loader must reside in the microSD card or in the Nand Memory.
-         cmp     r0, r1                  /* are we at the end yet            */
+==MMC Boot==
+===Prepare the microsd card===
+You can follow this howto about how [http://code.google.com/p/beagleboard/wiki/LinuxBootDiskFormat prepare the microsd card] or [[How to boot from MicroSD Card]]
-         add     r0, r0, #4              /* increment clear index pointer    */
+Get a new microsd card and create two partitions, the first one must be fat16/32 and the second one can be formated in any format type supported by linux kernel.
-         bne     clbss_l                 /* keep clearing till at end        */
+===Copy the files in the first (FAT) partition===
+In the first partition you must copy in this order:
+# x-loader.bin.ift (you must rename this file to MLO before copy it) / This is a signed image using contrib/signGP tool
+# x-loader configuration file [http://git.igep.es/?p=pub/scm/igep-x-loader.git;a=blob;f=scripts/igep.ini;h=ce093fe80c81d8888bf79464f847059b312bba83;hb=HEAD igep.ini]&nbsp;also you can change the configuration file name editing the file:&nbsp;[http://git.igep.es/?p=pub/scm/igep-x-loader.git;a=blob;f=include/configs/igep00x0.h igep00x0.h]&nbsp;(#define IGEP_BOOT_CFG_INI_FILE "igep.ini")
+# Your desired kernel image.
-         ldr     pc, _start_armboot      /* jump to C code                   */
+Load Order:
+<pre>  48 /* Linux Images */
+const char* LinuxImageNames [] = {
+         "kparam"   /* Use kparam first */
+         "zImage",   /* jffs2 it's case sensitive */
+         "zimage",   /* fat name it's not case sentitive */
+         "vmlinuz",
+         "bzImage",
+         "bzimage",
+         0,
+};
-_start_armboot: .word start_armboot
+or you can set the name for your kernel in the configuration file using the tag: kImageName
+</pre>
+Don't use a uImage kernel format (from uboot), only standard kernel formats be supported.
-</pre>
+'''kernel build command example''':
-<br>
-<br>
+<pre>make ARCH=arm CROSS_COMPILE=arm-poky-linux-gnueabi- zImage modules
-<pre> 175 cpu_init_crit:
+</pre>
-         /*
-          * Invalidate L1 I/D
+===Second Partition===
+Copy all your rootfs in this second partition.
-          */
+Also you can use the [http://releases.linaro.org/platform/linaro-m/headless/final/linaro-m-headless-tar-20101108-2.tar.gz linaro 10.11 minimal image]&nbsp;download the image and untar (as root) in your microsd card second partition.
-         mov     r0, #0                 /* set up for MCR */
+Remember install the kernel modules in this partition.
-         mcr     p15, 0, r0, c8, c7, 0  /* invalidate TLBs */
+Example:
-         mcr     p15, 0, r0, c7, c5, 1  /* invalidate icache */
+<pre>sudo make ARCH=arm CROSS_COMPILE=arm-poky-linux-gnueabi- modules_install INSTALL_MOD_PATH=[path to your target rootfs]
+</pre>
+==Nand Boot==
+===Nand Partitions===
+We've defined 3 partitions on the Nand Memory.
-         /* Invalide L2 cache (gp device call point)
+<pre>MTD partitions on "omap2-onenand":
+(a) 0x000000000000-0x000000080000&nbsp;: "X-Loader"
+(b) 0x000000080000-0x000000c80000&nbsp;: "Boot"
+(c) 0x000000c80000-0x000020000000&nbsp;: "File System"
+</pre>
+====X-Loader Partition====
+* Not fs formated (onenand raw)
+* Size: 0x80000 (512 KiB)
+* The xloader must be signed before copy it into the flash memory.
-          * - warning, this may have issues on EMU/HS devices
+You should copy the x-loader in the firsts 4 blocks (first 512 KiB), this is not a&nbsp;formated partition due the ROM not permits boot from a formated partition in flash, you should use flash_eraseall and [http://git.isee.biz/?p=pub/scm/writeloader.git;a=summary writeloader] for copy x-loader in the first blocks.
-          * this call can corrupt r0-r5
+<pre>Suggested procedure:
-          */
+Sign the x-loader before write it on the flash or microsd card.
+Sign x-loader:
-         mov r12, #0x1           @ set up to invalide L2
+You should execute contrib/signGP for sign the xloader that resides inside the flash memory.
+contrib/signGP x-load.bin
-smi:    .word 0xE1600070        @ Call SMI monitor
+The signed x-loader it's named: x-load.bin.ift
-         /*
-          * disable MMU stuff and caches
-          */
-         mrc     p15, 0, r0, c1, c0, 0
+Erase and copy the x-loader into the first flash partition (mtd0):
+flash_eraseall /dev/mtd0
+writeloader -i &lt;x-loader.bin.ift&gt; -o /dev/mtd0
+</pre>
+====<span id="1299156619608S" style="display: none;">&nbsp;</span>Boot Partition====
+* filesystem used jffs2 zlib/lzo compressed filesystem.
+* Suggested size: 0xC00000 (12 MiB).
-         bic     r0, r0, #0x00002000     @ clear bits 13 (--V-)
+X-Loader only support jffs2 partitions for boot partition.
-         bic     r0, r0, #0x00000007     @ clear bits 2:0 (-CAM)
+<u>Create the boot partition:</u>
-         orr     r0, r0, #0x00000002     @ set bit 1 (--A-) Align
-#ifndef CONFIG_ICACHE_OFF
-         orr     r0, r0, #0x00001800     @ set bit 11,12 (---I Z---) BTB,I-Cache
+<pre>Suggested procedure:
-#endif
+Erase all mtd1 content:
+flash_eraseall /dev/mtd1
-         mcr     p15, 0, r0, c1, c0, 0
+Create your partition:
+mount -t jffs2 /dev/mtdblock1 /mnt
+</pre>
+<u>Next uses:</u>
+<u></u>You can mount the partition over your boot directory in the rootfs
-         /*
+<pre>mount -t jffs2 /dev/mtdblock1 /boot</pre>
+You can use the cp command for copy your kernel and igep.ini configuration file.
-          * Jump to board specific initialization... The Mask ROM will have already initialized
+<pre>cp igep.ini /boot
+cp zImage /boot</pre>
+====Rootfs Partition====
+* fs (your prefered fs supported by linux, maybe a good choice it should be ubifs)
+* Size, all or you can create more partitions if you wish ...&nbsp;:)
-          * basic memory.  Go here to bump up clock rate and handle wake up conditions.
+==Boot Priority==
+XLoader first try load from mmc and if it fails then try from OneNand.
-          */
-         adr     r0, _start              /* r0 &lt;- current position of code   */
-         ldr     r1, _TEXT_BASE          /* test if we run from flash or RAM */
-         cmp     r0, r1                  /* pass on info about skipping some init portions */
-         moveq   r0,#0x1                 /* flag to skip prcm and sdrc setup */
-         movne   r0,#0x0
-         mov     ip, lr          /* persevere link reg across call */
-         bl      lowlevel_init   /* go setup pll,mux,memory */
-         mov     lr, ip          /* restore link */
-         mov     pc, lr          /* back to my caller */
-</pre>
-<br>
-it do a basic initialization and at end jump to the C initial function called [http://git.igep.es/?p=pub/scm/igep-x-loader.git;a=blob;f=lib/board.c start_armboot] defined in the file lib/board.c.<br>
-== C Execution Flow<br>  ==
-=== cpu_init<br>  ===
-Function: [http://git.igep.es/?p=pub/scm/igep-x-loader.git;a=blob;f=cpu/omap3/cpu.c cpu_init]<br>
-This function it's the responsable to do the CPU generic initialization and it's the first function called. <br>
-=== board_init<br>  ===
-Function: [http://git.igep.es/?p=pub/scm/igep-x-loader.git;a=blob;f=board/igep0020/igep0020.c board_init]<br>
-This function it's defined per board and it's the responsable to initialize the board,
-=== <br> <br> 4 Settings &amp; Configuration:  ===
-====== ================  ======
-.1 MMC Boot<br>------------<br>Get a new mmc and create two partitions, the first one must be fat (you can follow <br>this howto: http://code.google.com/p/beagleboard/wiki/LinuxBootDiskFormat)<br>In this first partition (boot partition) you should copy:
-*x-loader.bin.ift (you must rename this file to MLO) / This is a signed image using contrib/signGP tool<br>* igep.ini<br>* Your desired kernel image.
-Don't use a uImage kernel format (from uboot), only kernel formats be supported.
-Compilation Example:<br>$make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- zImage modules
-Read the kernel documentation about kernel images.
-.2 Setup igep.ini file<br>------------------------<br># Note this format permits use the characters<br># '#' and ';' as comment check file size restrictions
-[kernel]<br>kaddress=0x80008000<br>;rdaddress=0x84000000<br>serial.low=00000001<br>serial.high=00000000<br>revision=0001<br>;kImageName=<br>;kRdImageName=
-[kparams]<br>console=ttyS2,115200n8<br>;earlyprintk=serial,ttyS2,115200<br>mem=512M<br>boot_delay=0<br>;mpurate=800<br>;loglevel=7<br>omapfb.mode=dvi:1024x768MR-16@60<br>smsc911x.mac=0xb2,0xb0,0x14,0xb5,0xcd,0xde<br>;ubi.mtd=2<br>;root=ubi0:igep0020-rootfs <br>;rootfstype=ubifs<br>root=/dev/mmcblk0p2 rw rootwait
-----
-Tags Supported<br>---------------
-----
-[kernel] ----<br>* kaddress=0x80008000
-Kernel copy address, you should use the same address used in kernel image<br>configuration. If you don't know what it means maybe it's better don't change it.
-*rdaddress=0x84000000<br>Kernel RAM disk copy address. <br>If you don't know what it means maybe it's better don't change it.
-*serial.low=00000001<br>* serial.high=00000000<br>Board serial Number, you can read this information using /proc/cpuinfo
-*revision=0001<br>Board Revision ID, you can read this information using /proc/cpuinfo
-*kImageName=zImage<br>Kernel file name, if you don't provide this tag it try to load these others:<br>// DEFAULT IMAGES<br>"zImage"<br>"zimage"<br>"vmlinuz"<br>"bzImage"<br>"bzimage"
-*kRdImageName=rdimage<br>Kernel RAM Disk file, if you don't provide this tag it try to load these others:<br>// DEFAULT IMAGES<br>"initrd"
-----
-[kparams] ----<br>Kernel parameters, all these parameters are passed directly to the kernel using the<br>kernel command line.
+'''MLO (x-loader), igep.ini, zImage from MMC'''<br />If all it's present in the mmc it don't try to boot from Onenand.
-kernel parameters documentation:<br>http://www.kernel.org/doc/Documentation/kernel-parameters.txt<br>http://www.kernel.org/pub/linux/kernel/people/gregkh/lkn/lkn_pdf/ch09.pdf
+'''MLO (x-loader) in MMC, igep.ini and zImage in Onenand.'''<br />If only MLO it's provided this one try to load the other information from&nbsp;the Onenand.
-.3 Boot Priority<br>-----------------<br>First try mmc and if it fails then try from OneNand.
+It means that XLoader always try to load the information from MMC and if it fails then try to load from OneNand.
-Examples:<br>a) MLO (x-loader), igep.ini, zImage from MMC<br>If all it's present in the mmc it don't try to boot from Onenand.
+==Configuration file: igep.ini==
+[http://en.wikipedia.org/wiki/INI_file This entry in wikipedia] can help you how a ini file it's structured.
-b) MLO (x-loader) in MMC, igep.ini and zImage in Onenand.<br>If only MLO it's provided this one try to load the other information from<br>the Onenand.
+Inside the sources/scripts directory you can found a [http://git.isee.biz/?p=pub/scm/igep-x-loader.git;a=blob;f=scripts/igep.ini;h=ce093fe80c81d8888bf79464f847059b312bba83;hb=refs/heads/master igep.ini] example file.
-.4 OneNand Partition settings<br>-------------------------------<br>We suggest use minimum 3 partitions on the OneNand.
+The actual XLoader can handle two kind tags:
-Creating 3 MTD partitions on "omap2-onenand":<br>0x000000000000-0x000000080000&nbsp;: "X-Loader"<br>0x000000080000-0x000000c80000&nbsp;: "Boot"<br>0x000000c80000-0x000020000000&nbsp;: "File System"
+[kernel] Used for internal XLoader setup.
-.4.1) Xloader partition<br>* Not fs formated (raw)<br>* Suggested size: 0x80000 (512 KiB)<br>* The xloader must be signed before copy it in the flash memory.
+[kparams] Used for pass the linux kernel parameters.
-You should copy the x-loader in the firsts 4 blocks (first 512 KiB), this is not a <br>formated partition due the ROM not permits boot from there, you should use tools:<br>flash_eraseall and nandwrite for copy x-loader in the first blocks.
+===TAG: [kernel]&nbsp;===
+<pre>   1 [kernel]
+kaddress=0x80008000
+rdaddress=0x81600000
+serial.low=00000001
+serial.high=00000000
+revision=0001
+kImageName=zImage-test
+kRdImageName=rdImage-test
+MachineID=xxxx Where Machine ID = 2344 for IGEPv2,  ID = 2717 for IGEP COM Module, ID = 3203 for IGEP COM PROTON
+Mode=&lt;kernel&gt; or &lt;binary&gt;
+dss=&lt;0 or 1&gt; Enable or Disable Video Output
+dss_color=&lt;0x00FF8000&gt; Write your desired color in hex value
+dss_bitmap=&lt;filename&gt; Raw display image</pre>
+{| border="1" width="800" cellspacing="1" cellpadding="1"
+|-
+||Parameter Name
+||Description
+||Default Value
+||Comments
+|-
+||kaddress
+||Kernel copy address
+||0x80008000
+||hex memory address
+|-
+||rdaddress
+||Ram Disk location address
+||0x81600000
+||hex memory address
+|-
+||serial.low
+||Serial number (low part)
+||0 - 99999999
+||numeric
+|-
+||serial.high
+||Serial number (high part)
+||0 - 99999999
+||numeric
+|-
+||revision
+||Revision ID
+||0 - 9999
+||numeric
+|-
+||kImageName
+||Kernel, binary image name
+||N/A
+||Kernel or binary image name
+|-
+||kRdImageName
+||Ramdisk
+||N/A
+||Ram Disk image name
+|-
+||MachineID
+||Machine ID (kernel ID)
+||2717
+||2717 (IGEP COM Module) | 2344 IGEPv2 | 3203 (IGEP COM PROTON)
+|-
+||Mode
+||Boot Mode
+||kernel
+||kernel=linux kernel / binary=boot binary image
+|-
+||dss
+||Enable Video
+||0
+||0 = Disable, 1 Enable Video Output
+|-
+||dss_color
+||Video Color
+||0x00FF8000
+||Solid Color
+|-
+||dss_bitmap
+||Video Bitmap Image
+||string
+||filename with desired image
+|}
-Suggested procedure:
+===TAG:&nbsp;[kparams]===
+In this tag you can add all kernel parameters that you need, this is only an example:
-nand_eraseall /dev/mtd0<br>nandwrite -p /dev/mtd0 &lt;x-loader&gt;
+<pre>  10 [kparams]
+console=ttyS2,115200n8
+&nbsp;;earlyprintk=serial,ttyS2,115200
+mem=512M
+boot_delay=0
+&nbsp;;mpurate=800
+&nbsp;;loglevel=7
+omapfb.mode=dvi:1024x768MR-16@60\r
+smsc911x.mac=0xb2,0xb0,0x14,0xb5,0xcd,0xde\r
+&nbsp;;ubi.mtd=2
+&nbsp;;root=ubi0:igep0020-rootfs
+&nbsp;;rootfstype=ubifs
+root=/dev/mmcblk0p2 rw rootwait
-*Sign x-loader<br>You should execute contrib/signGP for sign the xloader that resides inside the flash memory.
+Also remember you can comment any line using ';' or '#' characters.
-contrib/signGP x-load.bin <br>The signed x-loader it's named: x-load.bin.ift
+</pre>
-Due the Onenand 512 MiB has two dies it's necessary split the x-loader and convert it to a 1 die binary.<br>This is a know OMAP/DM/AM OneNand/Nand boot limitation.
+=FAQ=
+==How I can boot from NFS?==
+Yes, you should add below parameters in the kparams tag:
-This is the procedure for create the x-loader OneNand binary:<br>You should execute: (You can use copy paste in your console)
+<pre>#smsc911x.mac fix your mac address
+smsc911x.mac=0xb2,0xb0,0x14,0xb5,0xcd,0xde
+# IP set you IP settings &lt;local_ip&gt;:&lt;server_ip&gt;:&lt;gateway&gt;:&lt;network_mask&gt;::&lt;interface&gt;:
+ip=192.168.2.123:192.168.2.105:192.168.2.1:255.255.255.0::eth0:
+# Set root as nfs
+root=/dev/nfs
+# Set your NFS root path as &lt;server_ip&gt;:&lt;rootfs_path&gt;
+nfsroot=192.168.2.105:/srv/nfs/linaro_minimal</pre>
+==How I can change the assigned kernel memory?==
+You can use the mem kernel variable as assign your desired kernel memory as:
-split -b 2K x-load.bin.ift split-<br>for file in `ls split-a?`; do cat $file &gt;&gt; x-load-ddp.bin.ift; cat $file &gt;&gt; x-load-ddp.bin.ift; done
+<pre>[kparams]
+mem=430M</pre>
+==How I can add more kernel variables?==
+You can add more variables creating a new variable - value pair under kparams tag as:
-This last command generate a file named x-load-ddp.bin.ift this is the x-loader for copy it in the OneNand.
+<pre>boot_delay=0</pre>
+==How I can modify my MAC address?==
+You can assign your desired mac address using the variable&nbsp;smsc911x.mac as:
-.4.2 Boot Partition<br>--------------------<br>* fs used jffs2 zlib compressed filesystem.<br>* Suggested size: 0xC00000 (12 MiB)
+<pre>smsc911x.mac=0xb2,0xb0,0x14,0xb5,0xcd,0xde</pre>
+==How I can boot my board using ubi root filesystem?==
+You should use these parameters:
-First time creation:<br>a) Use the same procedure described in point 4.2.1. Copy your jffs2 compressed image in the<br>partition, it can be a empty file.
+<pre>ubi.mtd=2
-b) Erase the partition and mount it as jffs2 filesystem then you can copy with cp command.
+root=ubi0:igep0020-rootfs
-Next Times:<br>Copy the files using cp command, or edit directly.
+rootfstype=ubifs</pre>
+==How I can boot my board using a RAM disk?==
+Use a RAMdisk it's fully supported.
-when kernel boots you can enable mount this partition over /boot directory for access all boot content.
+<pre>[kernel]
+rdaddress=0x81600000
+kRdImageName=ramdisk.bin
-.4.3 Rootfs <br>------------<br>* fs (your prefered fs supported by linux, maybe a good choice it should be ubifs)<br>* Size, all or you can create more partitions if you wish ...&nbsp;:)
+[kparams]
+root=/dev/ram0 rw
-<br>5 Build procedure<br>=================
+</pre>
+==Can I change the Processor frecuency?==
+Yes you can, IGEP X-loader configures the processor to boot at 600 Mhz you can select a different boot speed using the variable mpurate as:
-.1 Build with Ubuntu Cross Compiler gcc 4.5.1
+<pre>mpurate=800</pre>
+If you don't force any frequency the linux kernel will put your processor at the maximum speed (ex: DM3730 will run at 1 Ghz)
-*This is tested with Ubuntu 10.10
-a) Install the cross compiler:<br>apt-get install cpp-4.5-arm-linux-gnueabi g++-4.5-arm-linux-gnueabi
-b) Configure the board<br>make igep0020-sdcard_config
+==How I can boot downloading the kernel using wget?==
+The way for do that it's using one minimal kernel and RAMdisk (ex: using image-core-minimal from poky), the procedure can be more or less:
-c) Build<br>make
+a) Copy your minimal kernel and your Ramdisk inside the boot partition.
-d) Sign x-loader<br>You should execute contrib/signGP for sign the xloader that resides inside the flash memory.<br>contrib/signGP x-load.bin <br>The signed x-loader it's named: x-load.bin.ift
+b) Boot Normally from this kernel and Ramdisk, create one script your your desired command such wget http://192.168.15.22/mykernel.bin
-<br>5.2 Build with IGEP SDK
+c) Execute the script when boot (you can do that adding the script to the init enviroment)
-a) Source the enviroment<br>source /usr/local/poky/eabi-glibc/environment-setup-arm-none-linux-gnueabi
+d) if the downloading it's ok then execute the kexec call, first load the kernel and then pass to it your desired parameters.
-b) Edit the file Makefile<br>Find the define:
+e) finally boot the new kernel with kexec.
-And Set the variable as:<br>CROSS_COMPILE = arm-none-linux-gnueabi-
-b) Configure the board<br>make igep0020-sdcard_config
-c) build<br>make
+==My board not boot and I don't know what to do ...==
+When you test your IGEP X-loader, igep.ini file and kernel we suggest use a microsd card in front of use directly the flash nand, if your flash not boot copy all files in one microsd card and boot from there. You can check what happens removing some files from your microsd card for example if you wish test if your flashed kernel it's loaded in a right way then remove the kernel from your microsd card (note: use the same kernel name), IGEP X-loader first try load the file from your microsd card but if it's not found then it try to find the file in the flash.
-d) Sign x-loader<br>You should execute contrib/signGP for sign the xloader that resides inside the flash memory.<br>contrib/signGP x-load.bin <br>The signed x-loader it's named: x-load.bin.ift
+==How I can upgrade my old kernel?==
+Just copy the new one, the most secure way it's copy the new one and at end replace the igep.ini file with your new one.
-<br>5.3 Build Native
+<pre> mount -t jffs2 /dev/mtdblock1 /boot
-a) Configure the board<br>make igep0020-sdcard_config
+ cp newkernel.bin /boot
-b) Modify the config.mk file<br>Edit the variable CFLAGS and add the option: -fno-stack-protector
+ cp igep.ini /boot</pre>
+Use a different kernel name and you always can boot from your old one.
-CFLAGS&nbsp;:= $(CPPFLAGS) -Wall -Wstrict-prototypes -fno-stack-protector
+=6 Contribution &amp; Support &amp; Bugs Report=
+Contributions to this project be welcome and you can send your patches to support@iseebcn.com&nbsp;or you can use the igep forum for it.<br />You can access to IGEP-x-Loader repository using our git at [http://git.isee.biz/?p=pub/scm/igep-x-loader.git;a=summary git.isee.biz]<br />IGEP IRC Channel: [http://webchat.freenode.net/?channels=igep http://webchat.freenode.net/?channels=igep]
-c) build <br>make CROSS_COMPILE=""
-d) Sign x-loader<br>You should execute contrib/signGP for sign the xloader that resides inside the flash memory.<br>contrib/signGP x-load.bin <br>The signed x-loader it's named: x-load.bin.ift
+{{Message/Forum}}
-<br>6 Contribution &amp; Support &amp; Report Bugs<br>======================================<br>Contributions to this project be welcome and you can send your patches to support@iseebcn.com<br>or you can use the igep forum for it.<br>You can access to IGEP-x-Loader repository using our git at git.igep.es<br>IGEP IRC Channel: http://webchat.freenode.net/?channels=igep<br><br>
+[[Category:Boot_loaders|X_Loader]]

Personal tools

Search

Difference between revisions of "The IGEP X-loader"

From IGEP - ISEE Wiki