0
edits
Changes
From IGEP - ISEE Wiki
no edit summary
{| cellspacing="0" cellpadding="5" border="1" align="center" width="100%" style="text-align: left;"
|-
| bgcolor="#cccccc" |'''Getting started with IGEP0030IGEP COM MODULE'''
|-
|'''This page is a starting point for all products of the IGEP0030 family such IGEP COM MODULE.'''
|}
| bgcolor="#cccccc" colspan="3" | '''Overview'''
|-
| [[Image:Igep0030.jpg{{#lst:Template:Links|IGEP_COM_MODULE_Image}}|250px|center|link=Category{{#lst:IGEP0030Template:Links|IGEP_COM_MODULE_Community_MainPage}}]]
|-
|1) '''Connect USB OTG cable to a PC'''
|-
|2) '''Log into IGEP0030 IGEP COM MODULE via USB Ethernet Gadget'''
|-
|3) '''Log into IGEP0030 IGEP COM MODULE via Wifi'''
|}
This first chapter describes '''how to boot IGEP030IGEP COM MODULE''' and also gives some '''basic instructions''' about how to connect some peripherals.
| bgcolor="#cccccc" |'''Power up via USB OTG connector'''
|-
|'''Connect IGEP0030 IGEP COM MODULE to a computer via USB OTG'''
|-
|}
The on-board '''HS USB OTG port''' is used as the default '''power input for IGEP0030 IGEP COM MODULE standalone''' operating mode.
First of all, connect IGEP0030 IGEP COM MODULE to your machine via the on-board USB OTG port with '''a USB cable''' (USB A type plug to mini B type plug).
Connect IGEP0030 IGEP COM MODULE to your machine. It will power up.
=== Connect to IGEP0030 IGEP COM MODULE via USB OTG connector ===
----
|}
You can log into IGEP0030 IGEP COM MODULE via many '''interfaces with network connectivity''', such wifi, usb-ethernet gadget.. and many others (when connected to an IGEP Expansion Board).
In this section of this tutorial we are going to '''connect via USB Ethernet gadget'''. This feature allows you to have an IP connection over USB.
You can use this feature to interact with the IGEP Processor operating system [host] by typing commands in a client machine (your PC, for example) to perform specific tasks in IGEP0030IGEP COM MODULE. You can communicate and open a debug session via many other interfaces such Serial port, Ethernet, Wifi, USB Ethernet Gadget, etc. (if available in an IGEP Expansion Board, for example).
Therefore, you will be able to access IGEP0030 IGEP COM MODULE from your client device (for example, a PC with Linux, Windows, etc.)
The pre-installed software in IGEP0030 IGEP COM MODULE configures the USB interface with a static IP: 192.168.7.2
''Note: You will be able to change it later''
You can download it from its official page at: http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html
Then, run the '''SSH client''' and start a SSH session to connect to the host (IGEP0030IGEP COM MODULE) from the client (your PC):
[[Image:Putty ssh.png|center]]
# Select the '''SSH''' at connection type.
# Next insert the '''IP address of the target'''. In this case, the IGEP0030 IGEP COM MODULE default IP (192.168.7.2).
# Ensure that the port is set to '''22''', the default for SSH communications.
# Finally, push the '''Open button''' to start the SSH session.
If everything goes right, you will be able to access to an IGEP0030 IGEP COM MODULE console from your PC via USB Ethernet gadget.
=== Connect to IGEP0030 IGEP COM MODULE via Wifi ===
----
|}
By default, '''the pre-installed software in IGEP0030 IGEP COM MODULE enables the wifi interface''' and creates an Ad-Hoc network, with '''WLAN_IGEP as ESSID''' and a '''static IP address: 192.168.6.1'''.
If you have successfully followed the previous section of the tutorial, you might have used PuTTy to connect to IGEP0030 IGEP COM MODULE via USB Ethernet Gadget. In this section we will '''connect to your board using wifi'''.
Therefore, follow this instructions:
1. '''Connect to the WLAN_IGEP wireless network''' from IGEP0030 IGEP COM MODULE with a wireless adapter
2. '''Set a static IP''' within the subnet to your wireless adapter (for example: 192.168.6.2)
3. '''Open a PuTTy session''' and select SSH, 192.168.6.1 as target IP address.
4. '''Log into IGEP0030IGEP COM MODULE''' with login: root and empty password (press return)
You now have logged into IGEP0030 IGEP COM MODULE via its wireless connection.
{{Navigation/IGEP Technology Devices Guides/Getting Started/EndingNext Step|Name={{#lst:Template:Links|IGEP_COM_MODULE_Name}}|Community_MainPage={{#lst:Template:Links|IGEP_COM_MODULE_Community_MainPage}}|deviceNext_Step=IGEP0030{{#lst:Template:Links|IGEP_COM_MODULE_Community_Guides_2}}}}
[[Category:IGEP Technology Devices Guides]]
