|
|
| Line 1: |
Line 1: |
| − | = Introduction =
| |
| | | | |
| − | This article is for '''Yocto Project 1.8.1 - Poky 13.0.y Fido''' branch.<br> It is interesting read [[How to use the Yocto Project to develop Embedded Linux]] article previously.<br>
| |
| − |
| |
| − | = Build Platform Setup Environment =
| |
| − |
| |
| − | {{Message/Information Message|message= '''The instructions below are only for IGEP PROCESSOR BOARDS based on iMX6 processor.'''}}
| |
| − |
| |
| − | In order to build an image with BSP support for a given release, you need to download the corresponding BSP repository.
| |
| − |
| |
| − | <pre>git clone git://git.yoctoproject.org/poky</pre>
| |
| − |
| |
| − | Enter to the poky directory,
| |
| − |
| |
| − | <pre>cd poky</pre>
| |
| − |
| |
| − | Change tree to commit ee88b51cf2853ab075c9bd2ef7cf4d65d1c96674.
| |
| − |
| |
| − | <pre>git checkout ee88b51cf2853ab075c9bd2ef7cf4d65d1c96674 -b fido</pre>
| |
| − |
| |
| − | Clone the meta-fsl-arm layer.
| |
| − |
| |
| − | <pre>git clone -b fido https://github.com/Freescale/meta-fsl-arm.git</pre>
| |
| − |
| |
| − | Clone the meta-openembedded layer.
| |
| − |
| |
| − | <pre>git clone git://git.openembedded.org/meta-openembedded</pre>
| |
| − |
| |
| − | Enter to the meta-openembedded directory and enter to the meta-oe directory.
| |
| − |
| |
| − | <pre>cd meta-openembedded/
| |
| − | cd meta-oe/</pre>
| |
| − |
| |
| − | Change tree to commit 10d3c8f85280a0bf867a8e4f84bcda81c290d28e.
| |
| − |
| |
| − | <pre>git checkout 10d3c8f85280a0bf867a8e4f84bcda81c290d28e -b fido</pre>
| |
| − |
| |
| − | Clone the meta-isee layer.
| |
| − |
| |
| − | <pre>git clone git://git.isee.biz/pub/scm/meta-isee.git</pre>
| |
| − |
| |
| − | Clone the meta-fsl-arm-extra layer.
| |
| − |
| |
| − | <pre>git clone git://git.isee.biz/pub/scm/meta-fsl-arm-extra.git</pre>
| |
| − |
| |
| − |
| |
| − | <pre>source oe-init-build-env</pre>
| |
| − |
| |
| − | Having done that, you can build a igep image by adding the location of the layers to 'bblayers.conf'
| |
| − |
| |
| − | Add below line into .../poky/build/conf/bblayers.conf:
| |
| − |
| |
| − | <path to>/poky/meta-openembedded/meta-oe \
| |
| − | /poky/meta-fsl-arm \
| |
| − | /poky/meta-fsl-arm-extra \
| |
| − | /poky/meta-isee \
| |
| − |
| |
| − | To enable the isee layer, add the 'igep0046 MACHINE' to .../poky/build/conf/local.conf:
| |
| − |
| |
| − | MACHINE ?= "imx6q-igep0046"
| |
| − |
| |
| − | Add below lines in .../poky/build/conf/local.conf to accept the license (http://freescale.github.io/doc/release-notes/1.8/#license):
| |
| − |
| |
| − | <pre>ACCEPT_FSL_EULA = "1"
| |
| − | LICENSE_FLAGS_WHITELIST = "commercial license"</pre>
| |
| − |
| |
| − | You need the below packages for bitbake:
| |
| − |
| |
| − | <pre>sudo apt-get install texinfo
| |
| − | sudo apt-get install libsdl1.2-dev </pre>
| |
| − |
| |
| − | You should then be able to build a image as such:
| |
| − |
| |
| − | <pre>bitbake isee-image-dev</pre>
| |
| − |
| |
| − | At the end of a successful build, you should have an image that you could use for boot device from flash or a micro-SD card or you can create the installable firmware using:
| |
| − |
| |
| − | <pre> bitbake do-release-firmware </pre>
| |
