|
|
Line 1: |
Line 1: |
− | {{Table/IGEP Technology Devices
| |
− | |Tech_Family={{#lst:Template:Links|IGEPv2_Tech_Family}}
| |
− | |Tech_ID={{#lst:Template:Links|IGEPv2_Tech_ID}}
| |
− | |Name={{#lst:Template:Links|IGEPv2_Name}}
| |
− | |Image={{#lst:Template:Links|IGEPv2_Image}}
| |
− | |ISEE_MainPage={{#lst:Template:Links|IGEPv2_ISEE_MainPage}}
| |
− | |ISEE_Hardware={{#lst:Template:Links|IGEPv2_ISEE_Hardware}}
| |
− | }}
| |
| | | |
− |
| |
− | = Overview =
| |
− |
| |
− | This is the 1/3 chapter of the Getting Started with SMARC iMX6 Tutorial Guide. In this first chapter, we will learn :
| |
− |
| |
− | * Connect some peripherals, including monitor and USB peripherals.
| |
− | * Boot the board.
| |
− |
| |
− |
| |
− | Upon completion, you will be ready to continue with chapter 2/3 that explains more advanced tasks.
| |
− |
| |
− | You need build an image to your SD-card. Please see the article on [[Yocto Project 1.8 - Poky 13.0.y "Fido" | IGEP YOCTO Firmware]].
| |
− |
| |
− |
| |
− |
| |
− | = Requirements =
| |
− |
| |
− | In this tutorial we are going to use the following peripherals:
| |
− |
| |
− | * IGEP SMARC iMX6
| |
− | * BASEBOARD COMPATIBLE WITH SMARC with its power supply
| |
− | * SD-card with Yocto Project
| |
− | * Monitor compatible with HDMI
| |
− | * HDMI/HDMI cable
| |
− | * Network cable
| |
− | * USB keyboard and a mouse
| |
− | * PC
| |
− |
| |
− | = Getting started =
| |
− |
| |
− | You will learn how to connect some peripherals and power up the board.
| |
− |
| |
− | == Monitor ==
| |
− |
| |
− | [[Image:Paris db9.jpg|right|200px]] The board will connect to your HDMI monitor via its HDMI connector.
| |
− |
| |
− |
| |
− |
| |
− |
| |
− |
| |
− |
| |
− |
| |
− | == Network ==
| |
− |
| |
− | You may now plug the Ethernet cable into the 10/100 Ethernet jack of the board to get network access.
| |
− |
| |
− | == Keyboard/Mouse ==
| |
− |
| |
− | Now, plug your keyboard and mouse into any of the available USB.
| |
− |
| |
− | == SD-card ==
| |
− |
| |
− | Finally, plug the SD-card into the SD-card socket.
| |
− |
| |
− | == Booting ==
| |
− |
| |
− | With all the peripherals attached, plug in the wall adapter (5V DC) and power on your board. You will see a few lights flash.
| |
− |
| |
− |
| |
− | {{Navigation/IGEP Technology Guides/Getting Started/Ending
| |
− | |Next_Step={{#lst:Template:Links|IGEPv5_Community_Guides_2}}
| |
− | }}
| |
− |
| |
− | [[Category:IGEP Technology Devices Guides]]
| |