Revision as of 20:24, 25 January 2012

Overview

This How-To is meant to be a starting point for people to learn to set up UART2 for IGEPv2 J990 connector as quickly and easily as possible. In this how-to, we use Linaro Headless with Kernel 2.6.35.y. This How-To is focused for(WIFI/BT versions.

More information about UART: here and here.

There are three modes to configure UART2 in J990: via user space (first way), editing only igep.ini (second way) or editing kernel source and compile it (third way).

Feedback and Contributing

At any point, if you see a mistake you can contribute to this How-To.

First way

Fast Mode: the problem of this mode is when your system reboot or halt you will need to configure again, but you configure four UART wires in J990. Using user space to configure mux and disable bluetooth. Default kernel  has disabled TWL4030 PCM voice interface output pins to high impedance, otherwise this module forces the level of mcbsp3_fsx and mcbsp3_clkx pins. To make sure, go to ~/sound/soc/codecs/twl4030.c file already read:

	0x04, /* REG_VOICE_IF		(0xF)	*/

Configure IGEP

Make sure that IGEPv2 Expansion is disabled, go to igep.ini file:

;buddy=igep0022 

Disable Bluetooth:

Log with root user via SSH or Serial cable.

Go to /sys/kernel/debug/omap_mux/

Set sdmmc2_dat5 to gpio137 (mode 4):

echo 0x004 > sdmmc2_dat5 

Check that:

root@localhost:/sys/kernel/debug/omap_mux# cat sdmmc2_dat5
name: sdmmc2_dat5.gpio_137 (0x48002166/0x136 = 0x0004), b ah3, t NA
mode: OMAP_PIN_OUTPUT | OMAP_MUX_MODE4
signals: sdmmc2_dat5 | sdmmc2_dir_dat1 | cam_global_reset | sdmmc3_dat1 | gpio_137 | hsusb3_tll_stp | mm3_rxdp | safe_mode

Go to: /sys/class/gpio/

Check that gpio137 is in user space:

root@localhost:/sys/class/gpio# ls
export  gpio137  gpio138  gpio139  gpio170  gpio64  gpiochip0  gpiochip128  gpiochip160  gpiochip192  gpiochip32  gpiochip64  gpiochip96  unexport
root@localhost:/sys/class/gpio# 

If you don't have it, you should export gpio137:

echo 137 > /sys/class/gpio/export 

Set gpio137 to low value to disable bluetooth:

echo 0 > /sys/class/gpio/gpio137/value

Check that:

root@localhost:/sys/class/gpio# cat /sys/class/gpio/gpio137/value 
0
root@localhost:/sys/class/gpio# 

Disable Bluetooth UART2 wires:

Go to /sys/kernel/debug/omap_mux/

Type:

echo 0x007 > uart2_cts
echo 0x007 > uart2_rts
echo 0x007 > uart2_rx
echo 0x007 > uart2_tx 

Check that:

root@localhost:/sys/kernel/debug/omap_mux# cat uart2_cts 
name: uart2_cts.safe_mode (0x48002174/0x144 = 0x0007), b ab26, t NA
mode: OMAP_PIN_OUTPUT | OMAP_MUX_MODE7
signals: uart2_cts | mcbsp3_dx | gpt9_pwm_evt | NA | gpio_144 | NA | NA | safe_mode
root@localhost:/sys/kernel/debug/omap_mux# cat uart2_rts 
name: uart2_rts.safe_mode (0x48002176/0x146 = 0x0007), b ab25, t NA
mode: OMAP_PIN_OUTPUT | OMAP_MUX_MODE7
signals: uart2_rts | mcbsp3_dr | gpt10_pwm_evt | NA | gpio_145 | NA | NA | safe_mode
root@localhost:/sys/kernel/debug/omap_mux# cat uart2_rx 
name: uart2_rx.safe_mode (0x4800217a/0x14a = 0x0007), b ad25, t NA
mode: OMAP_PIN_OUTPUT | OMAP_MUX_MODE7
signals: uart2_rx | mcbsp3_fsx | gpt8_pwm_evt | NA | gpio_147 | NA | NA | safe_mode
root@localhost:/sys/kernel/debug/omap_mux# cat uart2_tx
name: uart2_tx.safe_mode (0x48002178/0x148 = 0x0007), b aa25, t NA
mode: OMAP_PIN_OUTPUT | OMAP_MUX_MODE7
signals: uart2_tx | mcbsp3_clkx | gpt11_pwm_evt | NA | gpio_146 | NA | NA | safe_mode
root@localhost:/sys/kernel/debug/omap_mux# 
 

Mode will be 7 (safe_mode)

Enable UART2 in J990:

Type:

echo 0x101 > mcbsp3_dx
echo 0x101 > mcbsp3_clkx
echo 0x101 > mcbsp3_fsx
echo 0x101 > mcbsp3_dr 

Check that:

root@localhost:/sys/kernel/debug/omap_mux# cat mcbsp3_dx 
name: mcbsp3_dx.uart2_cts (0x4800216c/0x13c = 0x0101), b af6, t NA
mode: OMAP_PIN_INPUT | OMAP_MUX_MODE1
signals: mcbsp3_dx | uart2_cts | NA | NA | gpio_140 | hsusb3_tll_data4 | NA | safe_mode
root@localhost:/sys/kernel/debug/omap_mux# cat mcbsp3_clkx 
name: mcbsp3_clkx.uart2_tx (0x48002170/0x140 = 0x0101), b af5, t NA
mode: OMAP_PIN_INPUT | OMAP_MUX_MODE1
signals: mcbsp3_clkx | uart2_tx | NA | NA | gpio_142 | hsusb3_tll_data6 | NA | safe_mode
root@localhost:/sys/kernel/debug/omap_mux# cat mcbsp3_fsx  
name: mcbsp3_fsx.uart2_rx (0x48002172/0x142 = 0x0101), b ae5, t NA
mode: OMAP_PIN_INPUT | OMAP_MUX_MODE1
signals: mcbsp3_fsx | uart2_rx | NA | NA | gpio_143 | hsusb3_tll_data7 | NA | safe_mode
root@localhost:/sys/kernel/debug/omap_mux# cat mcbsp3_dr 
name: mcbsp3_dr.uart2_rts (0x4800216e/0x13e = 0x0101), b ae6, t NA
mode: OMAP_PIN_INPUT | OMAP_MUX_MODE1
signals: mcbsp3_dr | uart2_rts | NA | NA | gpio_141 | hsusb3_tll_data5 | NA | safe_mode
root@localhost:/sys/kernel/debug/omap_mux# 
 

Mode will be 1 (uart mode)

Second way

Faster mode: configure kernel via IGEP Xloader. Configuration will be permanent.

NOTE: Only configures UART2_TX(6) and UART2_RX(8). You can not use UART2_CTS(4) AND UART2_RTS(10) which are usually referred to as hardware flow control. For example you can use RS232 but not RS485 peripheral. Don't use minicom with hardware flow control enable.
Go to igep.ini file, replaced by or type this:

buddy=igep0022 
buddy.modem=yes 

Third way (under construction)

Slow mode: configure kernel source.Configuration will be permanent.

Configure IGEP

Default kernel  has disabled TWL4030 PCM voice interface output pins to high impedance, otherwise this module forces the level of mcbsp3_fsx and mcbsp3_clkx pins. To make sure, go to ~/sound/soc/codecs/twl4030.c file already read:

	0x04, /* REG_VOICE_IF		(0xF)	*/

Make sure that IGEPv2 Expansion is disabled, go to igep.ini file:

;buddy=igep0022 

Please contribute

Test UART2 in J990

UART2 J990 pins:

Test

Connect UART2_TX with UART2_RX. Use minicom to prove UART2 (/dev/ttyS1) :

minicom -D /dev/ttyS1

If you write characters and see the echo on the screen, you configure correctly UART.