Difference between revisions of "Connectors Summary"

From IGEP - ISEE Wiki

Jump to: navigation, search
m
 
(44 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
= Overview  =
 
= Overview  =
  
This wiki has information about IGEP connectors. I used for this summary [[Linux Kernel 2.6.37.y|Kernel 2.6.37.y]](release:1)<br>
+
This wiki has information about IGEP connectors, this article is based in [[Linux Kernel 2.6.37.y|Kernel 2.6.37.y]] and IGEP Xloader without expansion support. You can find more information in schematics and manuals.<br>
 
 
More information in schematics and manuals.  
 
  
 
= Connectors  =
 
= Connectors  =
Line 10: Line 8:
  
 
*'''Pad''' number. See PCB.  
 
*'''Pad''' number. See PCB.  
*"'''Connect to'''" is a name used in schematics, usually it will be default peripheral name (mode=0)  
+
*"'''Pad Name'''" is a name used in schematics, usually it will be default peripheral name (mode=0)  
*IGEP '''main peripheral'''  
+
*IGEP '''Initial mode'''  
 
*'''Main utility'''  
 
*'''Main utility'''  
 
*'''Other available peripherals'''. See [[Mux configuration#Mode_selection|this page]] for more information:
 
*'''Other available peripherals'''. See [[Mux configuration#Mode_selection|this page]] for more information:
Line 27: Line 25:
 
== IGEPv2  ==
 
== IGEPv2  ==
  
{| width="200" cellspacing="1" cellpadding="1" border="1" align="center"
+
{{#lst:Category:IGEP0020|IGEP0020 expansion connectors}}
|-
 
| [[Image:Igepv2 rc photo2.jpg]]
 
|}
 
 
 
<br>
 
 
 
=== J990 connector  ===
 
 
 
Using this expansion connector you have access to McBSP1, McBSP3, I2C2, MMC2(8 bits), nReset and REGEN signals from OMAP Processor. The interface is at 1.8V on all signals. Only 1.8V CMOS levels are supported. Do not expose the header to 3.3V.
 
 
 
J990 connector is [http://beagleboard.org/ BeagleBoard] compatible expansion connector. IGEPv2-NOWIFI board is fully compatible. Other IGEPv2 board versions need software configuration to disable wifi interface and others because of shared hardware lines. MMC2 interface is used by wifi module. McBSP3 interface is used by PCM TPS65950 interface.
 
 
 
See which versions have WIFI/BT combo [[Frequently Asked Questions and Their Answers#Which_revision_is_my_IGEPv2_board.3F|available]].
 
 
 
{| cellspacing="1" cellpadding="1" border="1" align="JUSTIFY" style="width: 900px; height: 1740px;"
 
|-
 
| Pad
 
| Connect to
 
| Main peripheral
 
| Main utility
 
| Other available peripherals
 
| Share with
 
|-
 
| 1
 
| VIO 1V8
 
| -
 
| Power 1v8
 
| -
 
| -
 
|-
 
| 2
 
| DC 5V
 
| -
 
| Power 5v
 
| -
 
| -
 
|-
 
| 3
 
| MMC2_DAT7
 
| GPIO_139(mode=4)
 
| Reset WIFI
 
|
 
MMC2_DAT7(mode=0)<br>MMC2_CLKIN(mode=1)<br>MMC3_DAT3(mode=3)<br><font color="red">HSUSB3_TLL_NXT(mode=5)</font><br>MM3_RXDM(mode=6)<br>SAFE_MODE(mode=7)
 
 
 
| WIFI/BT combo:WIFI
 
|-
 
| 5
 
| MMC2_DAT6
 
| GPIO_138(mode=4)
 
| Power down WIFI
 
|
 
MMC2_DAT6(mode=0)<br>MMC2_DIR_CMD(mode=1)<br>MMC3_DAT2(mode=3)<br><font color="red">HSUSB3_TLL_DIR(mode=5)</font><br>SAFE_MODE(mode=7)
 
 
 
| WIFI/BT combo:WIFI
 
|-
 
| 7
 
| MMC2_DAT5
 
| GPIO_137(mode=4)
 
| Reset BT
 
|
 
MMC2_DAT5(mode=0)<br>MMC2_DIR_DAT1(mode=1)<br>MMC3_DAT1(mode=3)<br><font color="red">HSUSB3_TLL_STP(mode=5)</font><br>MM3_RXDP(mode=6)<br>SAFE_MODE(mode=7)
 
 
 
| WIFI/BT combo:BT
 
|-
 
| 9
 
| MMC2_DAT4
 
| GPIO136(mode=4)
 
| -
 
|
 
MMC2_DAT4(mode=0)<br>MMC_DIR_DAT0(mode=1)<br>MMC3_DAT0(mode=3)<br>SAFE_MODE(mode=7)
 
 
 
| WIFI/BT combo:WIFI
 
|-
 
| 11
 
| MMC2_DAT3
 
| MMC2_DAT3(mode=0)
 
| Transfer data
 
|
 
McSPI3_CS0(mode=1)<br>GPIO_135(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| WIFI/BT combo:WIFI
 
|-
 
| 13
 
| MMC2_DAT2
 
| MMC2_DAT2(mode=0)
 
| Transfer data
 
|
 
McSPI3_CS1(mode=1)<br>GPIO_134(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| WIFI/BT combo:WIFI
 
|-
 
| 15
 
| MMC2_DAT1
 
| MMC2_DAT1(mode=0)
 
| Transfer data
 
| GPIO_133(mode=4)<br>SAFE_MODE(mode=7)
 
| WIFI/BT combo:WIFI
 
|-
 
| 17
 
| MMC2_DAT0
 
| MMC2_DAT0(mode=0)
 
| Transfer data
 
|
 
McSPI3_SOMI(mode=1)<br>GPIO_132(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| WIFI/BT combo:WIFI
 
|-
 
| 19
 
| MMC2_CMD
 
| MMC2_CMD(mode=0)
 
| Control Wire for bus MMC2 (WIFI)
 
|
 
McSPI3_SIMO(mode=1)<br>GPIO_131(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| WIFI/BT combo:WIFI
 
|-
 
| 21
 
| MMC2_CLK0
 
| MMC2_CLK(mode=0)
 
| Clock for MMC2 (WIFI)
 
|
 
McSPI3_CLK(mode=1)<br>GPIO_130(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| WIFI/BT combo:WIFI
 
|-
 
| 4
 
| MCBSP3_DX
 
| MCBSP3_DX (mode=0)
 
| Transmitted serial Data (BT audio)
 
|
 
UART2_CTS(mode=1)<br>GPIO_140(mode=4)<br><font color="red">HSUSB3_TLL_D4(mode=5)</font><br>SAFE_MODE(mode=7)
 
 
 
| TPS65950: PCM VSP
 
|-
 
| 6
 
| MCBSP3_CLKX
 
| MCBSP3_CLKX(mode=0)
 
| Transmitted serial Clock (BT audio)
 
|
 
UART2_TX(mode=1)<br>GPIO_142(mode=4)<br><font color="red">HSUSB3_TLL_D6(mode=5)</font><br>SAFE_MODE(mode=7)
 
 
 
| BT/TPS65950: PCM VSP
 
|-
 
| 8
 
| MCBSP3_FSX
 
| MCBSP3_FSX (mode=0)
 
| Transmited Frame Syncronisation (BT audio)
 
|
 
UART2_RX(mode=1)<br>GPIO_143(mode=4)<br><font color="red">HSUSB3_TLL_D7(mode=5)</font><br>SAFE_MODE(mode=7)
 
 
 
| BT/TPS65950: PCM VSP
 
|-
 
| 10
 
| MCBSP3_DR
 
| MCBSP3_DR (mode=0)
 
| Received Serial Data (BT audio)
 
|
 
UART2_RTS(mode=1)<br>GPIO_141(mode=4)<br><font color="red">HSUSB3_TLL_D5(mode=5)</font><br>SAFE_MODE(mode=7)
 
 
 
| TPS65950: PCM VSP
 
|-
 
| 12
 
| MCBSP1_DX
 
| GPIO_158(mode=4)
 
| -
 
|
 
MCBSP1_DX(mode=0)<br>McSPI4_SIMO(mode=1)<br>McBSP3_DX(mode=2)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 14
 
| MCBSP1_CLKX
 
| GPIO_162(mode=4)
 
| -
 
|
 
MCBSP1_CLKX(mode=0)<br>McBSP3_CLKX(mode=2)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 16
 
| MCBSP1_FSX
 
| GPIO_161(mode=4)
 
| -
 
|
 
MCBSP1_FSX(mode=0)<br>McSPI4_CS0(mode=1)<br>McBSP3_FSX(mode=2)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 18
 
| MCBSP1_DR
 
| GPIO_159(mode=4)
 
| -
 
|
 
MCBSP1_DR(mode=0)<br>McSPI4_SOMI(mode=1)<br>McBSP3_DR(mode=2)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 20
 
| MCBSP1_CLKR
 
| GPIO_156(mode=4)
 
| -
 
| MCBSP1_CLKR(mode=0)<br>MCSPI4_CLK<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 22
 
| MCBSP1_FSR
 
| GPIO_157(mode=4)
 
| -
 
| MCBSP1_FSR(mode=0)<br>CAM_GLOBAL_RESET(mode=2)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 23
 
| I2C2_SDA
 
| I2C2_SDA(mode=0)
 
| I2C2 Data
 
| GPIO_183(mode=4)<br>SAFE_MODE(mode=7)
 
| CAM if configured via hardware: RC14
 
|-
 
| 24
 
| I2C2_SCL
 
| I2C2_SCL(mode=0)
 
| I2C2 Clock
 
| GPIO_168(mode=4)<br>SAFE_MODE(mode=7)
 
| CAM if configured via hardware: RC13
 
|-
 
| 25
 
| REGEN
 
| -
 
| Master/Slave control power TPS65950
 
| -
 
| -
 
|-
 
| 26
 
| nRESET
 
| -
 
| Read Reset Omap
 
| -
 
| -
 
|-
 
| 27
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 28
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|}
 
<br>
 
 
 
=== J960 connector  ===
 
 
 
This connector is used mainly to connect via serie to IGEP Software using [http://en.wikipedia.org/wiki/RS-232 RS232 standard].
 
 
 
On IGEPv2 revision B:
 
 
 
*This J960 connector has only Debug RS232 interface
 
*So, it is needed null modem configuration (direct connection between two computers). RX and TX lines are crossed in this null modem configuration between two equipments (TX1-&gt;RX2 / TX2-&gt;RX1).
 
 
 
On IGEPv2 revision C:
 
 
 
*You should modify your serial debug cable in order not to damage your serial PC port.&nbsp;
 
*Additional RS232 port (UART1) on same J960 connector. It is only needed to&nbsp; rotate 180o the IDC-10 (AT-Everex) to DB9 cable.
 
*It has been added resistors for alternative UART1, UART2 and UART3 hardware selection.
 
*See [[How to use UARTs#RS232_Schematic_Igep_V2|Schematics]] (RC) for more information.
 
 
 
{| cellspacing="1" cellpadding="1" border="1" style="width: 900px; height: 308px;"
 
|-
 
| Pad
 
| Connect to
 
| &nbsp; Main peripheral
 
| Main utility
 
| Other available peripherals (only via hardware)
 
|
 
Share with
 
 
 
|-
 
| 1
 
| -
 
| -
 
| -
 
| -
 
| -
 
|-
 
| 2
 
| RS232_RX2
 
| UART3_RX(R966)
 
| Serial debug
 
| UART2_RX(R952) only RC
 
| SN65C3232EPW
 
|-
 
| 3
 
| RS232_TX2
 
| UART3_TX(R965)
 
| Serial debug
 
| UART2_TX(R947) only RC
 
| SN65C3232EPW
 
|-
 
| 4
 
| -
 
| -
 
| -
 
| -
 
| -
 
|-
 
| 5
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 6
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 7
 
| -
 
| -
 
| -
 
| -
 
| -
 
|-
 
| 8
 
| RS232_TX1
 
| UART1_TX(R961)
 
| -
 
| UART3_TX(R940) only RC
 
| SN65C3232EPW
 
|-
 
| 9
 
| RS232_RX1
 
| UART1_RX(R962)
 
| -
 
| UART3_RX(R942) only RC
 
| SN65C3232EPW
 
|-
 
| 10
 
| -
 
| -
 
| -
 
| -
 
| -
 
|}
 
SN65C3232EPW: IC RS232 LINE DVR/RCVR
 
<br>
 
 
 
=== J940 connector  ===
 
 
 
This connector is used mainly to connect via RS485 (UART1) with other devices. User can use this connector to power the board with 5VDC. Use only 5V regulated DC. The IGEPv2 BOARD does not use this 9v power supply. Only on IGEPv2 revision B, the PWR_9V input is directly routed to JC01 and J971 connectors. On IGEPv2 revision C is not available.
 
 
 
{| cellspacing="1" cellpadding="1" border="1" style="width: 900px; height: 104px;"
 
|-
 
| Pad
 
| Connect to
 
| &nbsp; Main peripheral
 
| Main utility
 
| Other available peripherals
 
|
 
Share with
 
 
 
|-
 
| 1
 
| PWR_GND
 
| GND
 
| -
 
| -
 
| -
 
|-
 
| 2
 
| PWR_5V
 
| Power 5v
 
| -
 
| -
 
| -
 
|-
 
| 3
 
| PWR_9V
 
| Power 9v
 
| -
 
| -
 
| -
 
|-
 
| 4
 
| RS485_A
 
| UART3_RX/UART3_TX
 
| A aka '−' aka TxD-/RxD- aka inverting pin
 
| -
 
| TXS0102DCUR
 
|-
 
| 5
 
| RS485_B
 
| UART3_RX/UART3_TX
 
| B aka '+' aka TxD+/RxD+ aka non-inverting pin
 
| -
 
| TXS0102DCUR
 
|}
 
TXS0102DCUR: Bidirectional voltage-level translator
 
<br>
 
 
 
=== J400 connector  ===
 
 
 
J400 is used to [http://en.wikipedia.org/wiki/Jtag JTAG] (Joint Test Action Group). JTAG is a standardized serial protocol widely used in printed circuit boards. Its main functions are:
 
 
 
*Debug the software of an embedded system directly
 
*Storing firmware
 
*Boundary scan testing
 
 
 
JTAG Suggested:
 
 
 
*JTAG Debugger XDS510+ USB from Spectrum Digital with Code Composer Studio 3.3 or higher.
 
*JTAG Debugger XD100v2 USB from Spectrum Digital with Code Composer Studio 4 or higher.
 
 
 
{| cellspacing="1" cellpadding="1" border="1" style="width: 900px; height: 104px;"
 
|-
 
| Pad
 
| Connect to
 
| &nbsp; Main peripheral
 
| Main utility
 
| Other available peripherals
 
|
 
Share with
 
 
 
|-
 
| 1
 
| JTAG_TMS
 
| JTAG_TMS
 
| <br>
 
| -
 
| -
 
|-
 
| 2
 
| JTAG_NTRST
 
| JTAG_NTRST
 
| <br>
 
| -
 
| -
 
|-
 
| 3
 
| JTAG_TDI
 
| JTAG_TDI
 
| <br>
 
| -
 
| -
 
|-
 
| 4
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 5
 
| 1V8
 
| Power 1V8
 
| <br>
 
| -
 
| -
 
|-
 
| 6
 
| -
 
| -
 
| <br>
 
| -
 
| -
 
|-
 
| 7
 
| JTAG_TD0
 
| JTAG_TD0
 
| <br>
 
| -
 
| -
 
|-
 
| 8
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 9
 
| JTAG_RTCK
 
| JTAG_RTCK
 
| <br>
 
| -
 
| -
 
|-
 
| 10
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 11
 
| JTAG_TCK
 
| JTAG_TCK
 
| <br>
 
| -
 
| -
 
|-
 
| 12
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 13
 
| JTAG_EMU0
 
| JTAG_EMU0(mode=0)
 
| <br>
 
| GPIO_11(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 14
 
| JTAG_EMU1
 
| JTAG_EMU1(mode=0)
 
| <br>
 
| GPIO_31(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|}
 
 
 
<br>
 
 
 
=== J970 connector  ===
 
 
 
J970 is used to implement a keypad, it is connected to TPS65950. The keypad interface controller provides an enhanced keypad decode capability and simultaneously reduces host processor software overhead. When a key button of the keyboard matrix is pressed the corresponding row and column lines are shorted together. To allow key press detection, all input pins (KBR) are pulled up to VCC and all output pins (KBC) driven to a low level. Any action on a button generates an interrupt to the sequencer. The decoding sequence is written to allow detection of simultaneous press actions on several key buttons.
 
 
 
More information in [http://www.ti.com/product/tps65950 TPS65950] datasheets. TPS65950 send via I2C1 all the interrupt request.
 
 
 
{| cellspacing="1" cellpadding="1" border="1" style="width: 900px; height: 216px;"
 
|-
 
|
 
*Can handle up to 8 x 8 keypads, IGEPv2 can handle up to 4 x 4 keypads.
 
*Optionally, you can decode via Omap software.
 
*Event detection on key press and key release.
 
*Multikey press detection, can detect up 2&nbsp; keys at the same time.
 
*Long-key detection on prolonged key press.
 
*Programmable time-out on permanent key press or after keypad release.
 
 
 
| [[Image:Igep keypad.png]]
 
|}
 
 
 
{| cellspacing="1" cellpadding="1" border="1" style="width: 900px; height: 101px;"
 
|-
 
| Pad
 
| Connect to
 
| Main peripheral
 
| Main utility
 
| Other available peripherals
 
|
 
Share with
 
 
 
|-
 
| 1
 
| KPD_CO
 
| KPD_CO
 
| Keypad controler Column 0
 
| -
 
| -
 
|-
 
| 2
 
| KPD_C1
 
| KPD_C1
 
| Keypad controler Column 1
 
| -
 
| -
 
|-
 
| 3
 
| KPD_C2
 
| KPD_C2
 
| Keypad controler Column 2
 
| -
 
| -
 
|-
 
| 4
 
| KPD_C3
 
| KPD_C3
 
| Keypad controler Column 3
 
| -
 
| -
 
|-
 
| 5
 
| KPD_RO
 
| KPD_RO
 
| Keypad controler Row 0
 
| -
 
| -
 
|-
 
| 6
 
| KPD_R1
 
| KPD_R1
 
| Keypad controler Row 1
 
| -
 
| -
 
|-
 
| 7
 
| KPD_R2
 
| KPD_R2
 
| Keypad controler Row 2
 
| -
 
| -
 
|-
 
| 8
 
| KPD_R3
 
| KPD_R3
 
| Keypad controler Row 3
 
| -
 
| -
 
|}
 
 
 
 
 
 
 
 
=== JC30 connector  ===
 
 
 
These connectors allow the access to the Camera interface signals. Omap has the processing capability to connect RAW image-sensor modules via this connector. <br>
 
 
 
{| cellspacing="1" cellpadding="1" border="1" style="width: 900px; height: 104px;"
 
|-
 
| Pad
 
| Connect to
 
| Main peripheral
 
| Main utility
 
| Other available peripherals
 
|
 
Share with
 
 
 
|-
 
| 1
 
| CAM_HS
 
| GPIO_94(mode=4)
 
| -
 
| CAM_HS(mode=0)<br>HW_DBG0(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 2
 
| CAM_VS
 
| GPIO_95(mode=4)
 
| -
 
| CAM_VS(mode=0)<br>HW_DBG1(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 3
 
| CAM_XCLKA
 
| CAM_XCLKA(mode=0)
 
| Camera interface
 
| GPIO_96(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 4
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 5
 
| CAM_PCLK
 
| CAM_PCLK(mode=0)
 
| Camera interface
 
| GPIO_97(mode=4)<br>HW_DBG2(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 6
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 7
 
| CAM_DO
 
| GPIO_99(mode=4)
 
| -
 
| CAM_DO(mode=0)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 8
 
| CAM_FLD
 
| GPIO_98(mode=4)
 
| -
 
| CAM_FLD(mode=0)<br>CAM_GLOBAL_RESET(mode=2)<br>HW_DBG3(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 9
 
| CAM_D2
 
| CAM_D2(mode=0)
 
| Camera interface
 
| GPIO_101(mode=4)<br>HW_DBG4(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 10
 
| CAM_D1
 
| GPIO_100(mode=4)
 
| -
 
| CAM_D1(mode=0)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 11
 
| CAM_D4
 
| CAM_D4(mode=0)
 
| Camera interface
 
| GPIO_103(mode=4)<br>HW_DBG6(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 12
 
| CAM_D3
 
| CAM_D3(mode=0)
 
| Camera interface
 
| GPIO_102(mode=4)<br>HW_DBG5(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 13
 
| CAM_D6
 
| GPIO_105(mode=4)
 
| -
 
| CAM-D6(mode=0)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 14
 
| CAM_D5
 
| CAM_D5(mode=0)
 
| Camera interface
 
| GPIO_104(mode=4)<br>HW_DBG7(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 15
 
| CAM_D8
 
| GPIO_107(mode=4)
 
| -
 
| CAM_D8(mode=0)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 16
 
| CAM_D7
 
| GPIO_106(mode=4)
 
| -
 
| CAM_D7(mode=0)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 17
 
| CAM_D10
 
| CAM_D10(mode=0)
 
| Camera interface
 
| GPIO_109(mode=4)<br>HW_DBG8(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 18
 
| CAM_D9
 
| GPIO_108(mode=4)
 
| -
 
| CAM_D9(mode=0)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 19
 
| CAM_XCLKB
 
| CAM_XCLKB(mode=0)
 
| Camera interface
 
| GPIO_111(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 20
 
| CAM_D11
 
| CAM_D11(mode=0)
 
| Camera interface
 
| GPIO_110(mode=4)<br>HW_DBG9(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 21
 
| GPIO_112/I2C2_SCL
 
| GPIO_112(RC11)
 
| -
 
| I2C2_SCL(RC13)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 22
 
| GPIO_113/I2C2_SDA
 
| GPIO_113(RC12)
 
| -
 
| I2C2_SDA(RC14)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 23
 
| CAM_RESET
 
| GPIO_114(mode=4)
 
| <br>
 
| CAM_RESET(mode=0)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 24
 
| CAM_PDN
 
| GPIO_115(mode=4)
 
| <br>
 
| CAM_PDN(mode=0)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 25
 
| CAM_STROBE
 
| CAM_STROBE(mode=0)
 
| Camera interface
 
| GPIO_126(mode=4)<br>HW_DBG11(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 26
 
| CAM_WEN
 
| GPIO_167(mode=4)
 
| -
 
| CAM_WEN(mode=0)<br>CAM_SHUTTER(mode=2)<br>HW_DBG10(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 27
 
| 3V3
 
| -
 
| Power 3V3
 
| -
 
| -
 
|-
 
| 28
 
| 3V3
 
| -
 
| Power 3V3
 
| -
 
| -
 
|}
 
 
 
<br>
 
 
 
=== TFT CONNECTORS: JA41-JA42  ===
 
 
 
These connectors allow the access to the LCD signals.The output signal is shared by HDMI-A
 
 
 
==== JA41 connector  ====
 
 
 
JA41 is used for DVI (Digital Video Interface) data part.
 
 
 
IGEPv2 RB version:
 
 
 
*Available only the first 20 pads
 
 
 
IGEPv2 RC version:
 
 
 
*Available 28 pads
 
 
 
{| cellspacing="1" cellpadding="1" border="1" align="JUSTIFY" style="width: 900px; height: 1064px;"
 
|-
 
| Pad:
 
| Connect to
 
| Main peripheral
 
| Main utility
 
| Other available peripherals
 
| Share with
 
|-
 
| 1
 
| VIO 3V3
 
| -
 
| Power 3v3
 
| -
 
| -
 
|-
 
| 2
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 3
 
| DVI_DATA0
 
| DSS_D0(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
UART1_CTS(mode=2)<br><font color="red">DSSVENC656_DATA0(mode=3)</font><br>GPIO_70(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 4
 
| DVI_DATA1
 
| DSS_D1(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
UART1_RTS(mode=2)<br><font color="red">DSSVENC656_DATA1(mode=3)</font><br>GPIO_71(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 5
 
| DVI_DATA2
 
| DSS_D2(mode=0)
 
| LCD&nbsp;pixel data bit
 
| <font color="red">DSSVENC656_DATA2(mode=3)</font><br>GPIO_72(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 6
 
| DVI_DATA3
 
| DSS_D3(mode=0)
 
| LCD&nbsp;pixel data bit
 
| <font color="red">DSSVENC656_DATA3(mode=3)</font><br>GPIO_73(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 7
 
| DVI_DATA4
 
| DSS_D4(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
<font color="red">DSSVENC656_DATA4(mode=3)</font><br>UART3_RX(mode=2)<br>GPIO_74(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 8
 
| DVI_DATA5
 
| DSS_D5(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
<font color="red">DSSVENC656_DATA5(mode=3)</font><br>UART3_TX(mode=2)<br>GPIO_75(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 9
 
| DVI_DATA6
 
| DSS_D6(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
<font color="red">DSSVENC656_DATA6(mode=3)</font><br>UART1_TX(mode=2)<br>GPIO_76(mode=4)<br>HW_DBG14(mode=5)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 10
 
| DVI_DATA7
 
| DSS_D7(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
<font color="red">DSSVENC656_DATA7(mode=3)</font><br>UART1_RX(mode=2)<br>GPIO_77(mode=4)<br>HW_DBG15(mode=5)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 11
 
| DVI_DATA8
 
| DSS_D8(mode=0)
 
| LCD&nbsp;pixel data bit
 
| GPIO_78(mode=4)<br>HW_DBG16(mode=5)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 12
 
| DVI_DATA9
 
| DSS_D9(mode=0)
 
| LCD&nbsp;pixel data bit
 
| GPIO_79(mode=4)<br>HW_DBG17(mode=5)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 13
 
| DVI_DATA10
 
| DSS_D10(mode=0)
 
| LCD&nbsp;pixel data bit
 
| GPIO_80(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 14
 
| DVI_DATA11
 
| DSS_D11(mode=0)
 
| LCD&nbsp;pixel data bit
 
| GPIO_81(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 15
 
| DVI_DATA12
 
| DSS_D12(mode=0)
 
| LCD&nbsp;pixel data bit
 
| GPIO_82(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 16
 
| DVI_DATA13
 
| DSS_D13(mode=0)
 
| LCD&nbsp;pixel data bit
 
| GPIO_83(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 17
 
| DVI_DATA14
 
| DSS_D14(mode=0)
 
| LCD&nbsp;pixel data bit
 
| GPIO_84(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 18
 
| DVI_DATA15
 
| DSS_D15(mode=0)
 
| LCD&nbsp;pixel data bit
 
| GPIO_85(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 19
 
| DVI_DATA16
 
| DSS_D16(mode=0)
 
| LCD&nbsp;pixel data bit
 
| GPIO_86(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 20
 
| DVI_DATA17
 
| DSS_D17(mode=0)
 
| LCD&nbsp;pixel data bit
 
| GPIO_87(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 21
 
| DVI_DATA18
 
| DSS_D18(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
DSS_D0 (mode=3)<br>MCSPI3_CLK(mode=2)<br>GPIO_88(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 22
 
| DVI_DATA19
 
| DSS_D19(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
DSS_1 (mode=3)<br>MCSPI3_SIMO(mode=2)<br>GPIO_89(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 23
 
| DVI_DATA20
 
| DSS_D20(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
DSS_D2 (mode=3)<br>MCSPI3_SOMI(mode=2)<br>GPIO_90(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 24
 
| DVI_DATA21
 
| DSS_D21(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
DSS_D3 (mode=3)<br>MCSPI3_CSO(mode=2)<br>GPIO_91(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 25
 
| DVI_DATA22
 
| DSS_D22(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
DSS_D4 (mode=3)<br>MCSPI3_CS1(mode=2)<br>GPIO_92(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 26
 
| DVI_DATA23
 
| DSS_D23(mode=0)
 
| LCD&nbsp;pixel data bit
 
|
 
DSS_D5(mode=3)<br>GPIO_93(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| TFP410
 
|-
 
| 27
 
| I2C3_SCL
 
| I2C3_SCL(mode=0)
 
| I2C3 Clock
 
| GPIO_184(mode=4)<br>SAFE_MODE(mode=7)
 
| TXS0102DCUR
 
|-
 
| 28
 
| I2C3_SDA
 
| I2C3_SDA(mode=0)
 
| I2C3 Data
 
| GPIO_185(mode=4)<br>SAFE_MODE(mode=7)
 
| TXS0102DCUR
 
|}
 
 
 
<br> TFP410: converts DVI signal to HDMI
 
 
 
TXS0102DCUR: Increse I2c3 voltage to 5V to read EDID information <br>
 
 
 
==== JA42 connector  ====
 
 
 
JA42 is used for DVI (Digital Video Interface) control part, TouchScreen control and SPI1.
 
 
 
The current available on the DC_5V rail is limited to the available current that remains from the DC supply that is connected to the DC power jack on the board. Keep in mind that some of that power is needed by the USB Host power rail and if more power is needed for the expansion board, the main DC power supply current capability may need to be increased. All signals are 1.8V except the DVI_PUP which is a 3.3V signal. The 1.8V rail is for level translation only and should not be used to power circuitry on the board. The 3.3V rail also has limited capacity on the power as well. It is suggested that the 5V rail be used to generate the required voltages for an adapter card. <br>
 
 
 
{| cellspacing="1" cellpadding="1" border="1" align="JUSTIFY" style="width: 900px; height: 343px;"
 
|-
 
| Pad
 
| Connect to
 
| Main peripheral
 
| Main utility
 
| Other available peripherals
 
| Share with
 
|-
 
| 1
 
| VIO 1V8
 
| -
 
| Power 1v8
 
| -
 
| -
 
|-
 
| 2
 
| SYS_BOOT5
 
| GPIO_7(mode=4)
 
| Omap boot config
 
|
 
SYS_BOOT5(mode=0)<br>MMC2_DIR_DAT(mode=1)<br><font color="blue">DSS_DATA22(mode=3)</font><br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 3
 
| DC_5V
 
| -
 
| Power 5v
 
| -
 
| -
 
|-
 
| 4
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 5
 
| SYS_BOOT0
 
| GPIO_2(mode=4)
 
| Omap boot config
 
| SYS_BOOT0(mode=0)<br><font color="blue">DSS_DATA18(mode=3)</font><br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 6
 
| SYS_BOOT1
 
| GPIO_3(mode=4)
 
| Omap boot config
 
| SYS_BOOT1(mode=0)<br><font color="blue">DSS_DATA19(mode=3)</font><br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 7
 
| DVI_VSYNC
 
| DSS_VSYNC(mode=0)
 
| LCD&nbsp;vertical sync (Expansion)
 
| GPIO_68(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 8
 
| DVI_HSYNC
 
| DSS_HSYNC(mode=0)
 
| LCD Horitzontal sync (Expansion)
 
| GPIO_67 (mode=4)<br>HW_DBG13(mode=5)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 9
 
| DVI_ACBIAS
 
| DSS_ACBIAS(mode=0)
 
| LCD Control (Expansion)
 
| GPIO_69(mode=4)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 10
 
| DVI_PUP
 
| -
 
| Control signal for DVI controller (Expansion)
 
| -
 
| TFP410
 
|-
 
| 11
 
| DVI_PCLK
 
| DSS_PCLK(mode=0)
 
| LCD clock (Expansion)
 
| GPIO_66(mode=4)<br>HW_DBG12(mode=5)<br>SAFE_MODE(mode=7)
 
| TFP410
 
|-
 
| 12
 
| TS_nPEN_IRQ
 
| GPIO_175(mode=4)
 
| Touchscreen control (Expansion)
 
| McSPI1_CS1(mode=0)<br>MMC3_CMD(mode=3)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 13
 
| LCD_QVGA/nVGA
 
| GPIO_154(mode=4)
 
| Touchscreen control (Expansion)
 
| McBSP4_DX(mode=0)<br><font color="red">HSUSB3_TLL_DATA2(mode=5)</font><br>MM3_TXDAT(mode=6)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 14
 
| LCD_ENVDD
 
| GPIO_153(mode=4)
 
| Touchscreen control (Expansion)
 
| McBSP4_DR(mode=0)<br><font color="red">HSUSB3_TLL_DATA0(mode=5)</font><br>MM3_RXRCV(mode=6)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 15
 
| LCD_RESB
 
| GPIO_155(mode=4)
 
| Touchscreen control (Expansion)
 
| McBSP4_FSX(mode=0)<br><font color="red">HSUSB3_TLL_DATA3(mode=5)</font><br>MM3_TXEN_N(mode=6)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 16
 
| LCD_INI
 
| GPIO_152(mode=4)
 
| Touchscreen control (Expansion)
 
| McBSP4_CLKX(mode=0)<br><font color="red">HSUSB3_TLL_DATA1(mode=5)</font><br>MM3_TXSE0(mode=6)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 17
 
| MCSPI1_CLK
 
| McSPI1_CLK(mode=0)
 
| Touchscreen control (Expansion)
 
|
 
MMC2_DAT4(mode=1)<br>GPIO_171(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 18
 
| MCSPI1_SIMO
 
| McSPI1_SIMO(mode=0)
 
| Touchscreen control (Expansion)
 
|
 
MMC2_DAT5(mode=1)<br>GPIO_172(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 19
 
| MCSPI1_CS0
 
| McSPI1_CS0(mode=0)
 
| Touchscreen control (Expansion)
 
|
 
MMC2_DAT7(mode=1)<br>GPIO_174(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 20
 
| MCSPI1_SOMI
 
| McSPI1_SOMI(mode=0)
 
| Touchscreen control (Expansion)
 
|
 
MMC2_DAT6(mode=1)<br>GPIO_173(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|}
 
TFP410: converts DVI signal to HDMI
 
<br>
 
  
 
== IGEP MODULE  ==
 
== IGEP MODULE  ==
  
{| width="200" cellspacing="1" cellpadding="1" border="1" align="center"
+
{{#lst:Category:IGEP0030|IGEP0030 expansion connectors}}
|-
 
| [[Image:Module description small.jpg]]
 
|}
 
 
 
<br>'''NOTE: By default, J7 connector is not mounted'''
 
 
 
=== J5 connector  ===
 
 
 
OMAP3 processor family has Camera Image Signal Processing (ISP) interface. ISP interface could to be connecting to CCD and CMOS image sensors.
 
 
 
Detailed features of ISP are:
 
 
 
*CCD and CMOS Imager Interface
 
*Memory Data Input
 
*BT.601/BT.656 Digital YCbCr 4:2:2 (8-/10-Bit) Interface
 
*Glueless Interface to Common Video Decoders
 
*Resize Images From 1/4x to 4x
 
*Separate Horizontal/Vertical Control
 
 
 
The signals of connector J5 are connected directly to the processor.
 
 
 
{| cellspacing="1" cellpadding="1" border="1" style="width: 900px; height: 104px;"
 
|-
 
| Pad
 
| Connect to
 
| Main peripheral
 
| Main utility
 
| Other available peripherals
 
|
 
Share with
 
 
 
|-
 
| 1
 
| GPIO94_CAM_HS
 
| CAM_HS(mode=0)
 
| LCD Horitzontal sync
 
| GPIO_94(mode=4)<br>HW_DBG0(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 2
 
| GPIO95_CAM_VS
 
| GPIO_95(mode=4
 
| -
 
| xGPIO_95(mode=4)<br>HW_DBG1(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 3
 
| GPIO96_CAM_XCLKA
 
| CAM_XCLKA(mode=0)
 
| Camera interface
 
| GPIO_96(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 4
 
| GPIO97_CAM_PCLK
 
| CAM_PCLK(mode=0)
 
| Camera interface
 
| GPIO_97(mode=4)<br>HW_DBG2(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 5
 
| GPIO98_CAM_FLD
 
| GPIO_98(mode=4)
 
| -
 
| CAM_FLD(mode=0)<br>CAM_GLOBAL_RESET(mode=2)<br>HW_DBG3(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 6
 
| GPIO99_CAM_D0
 
| CAM_D0(mode=0)
 
| Camera interface
 
| GPIO_99(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 7
 
| GPIO100_CAM_D1
 
| CAM_D1(mode=0)
 
| Camera interface
 
| GPIO_100(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 8
 
| GPIO101_CAM_D2
 
| CAM_D2(mode=0)
 
| Camera interface
 
| GPIO_101(mode=4)<br>HW_DBG4(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 9
 
| GPIO102_CAM_D3
 
| CAM_D3(mode=0)
 
| Camera interface
 
| GPIO_102(mode=4)<br>HW_DBG5(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 10
 
| GPIO103_CAM_D4
 
| CAM_D4(mode=0)
 
| Camera interface
 
| GPIO_103(mode=4)<br>HW_DBG6(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 11
 
| GPIO104_CAM_D5
 
| CAM_D5(mode=0)
 
| Camera interface
 
| GPIO_104(mode=4)<br>HW_DBG7(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 12
 
| GPIO105_CAM_D6
 
| CAM_D6(mode=0)
 
| Camera Interface
 
| GPIO_105(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 13
 
| GPIO106_CAM_D7
 
| CAM_D7(mode=0)
 
| Camera interface
 
| GPIO_106(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 14
 
| GPIO107_CAM_D8
 
| CAM_D8(mode=0)
 
| Camera interface
 
| GPIO_107(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 15
 
| GPIO108_CAM_D9
 
| CAM_D9(mode=0)
 
| Camera interface
 
| GPIO_108(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 16
 
| GPIO109_CAM_D10
 
| CAM_D10(mode=0)
 
| Camera interface
 
| GPIO_109(mode=4)<br>HW_DBG8(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 17
 
| GPIO110_CAM_D11
 
| CAM_D11(mode=0)
 
| Camera interface
 
| GPIO_110(mode=4)<br>HW_DBG9(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 18
 
| GPIO111_CAM_XCLKB
 
| CAM_XCLKB(mode=0)
 
| Camera interface
 
| GPIO_111(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 19
 
| GPIO167_CAM_WEN
 
| GPIO_167(mode=4)
 
| -
 
| CAM_WEN(mode=0)<br>CAM_SHUTTER(mode=2)<br>HW_DBG10(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 20
 
| GPIO126_CAM_STROBE
 
| CAM_STROBE(mode=4)
 
| Camera interface
 
| GPIO_126(mode=4)<br>HW_DBG11(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 21
 
| VIO_1V8
 
| -
 
| Power 1V8
 
| -
 
| -
 
|-
 
| 22
 
| PMIC_SYSEN
 
| -
 
| Control Slave power ICs
 
| -
 
| TPS65950: CONTROL
 
|-
 
| 23
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 24
 
| VBAT
 
| -
 
| Board supply: 3V5-4V2
 
| -
 
| -
 
|-
 
| 25
 
| GPIO63_CAM_IRQ
 
| GPMC_WAIT1(mode=0)
 
| -
 
| GPIO_63(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 26
 
| GPIO184_I2C3_SCL
 
| I2C3_SCL(mode=0)
 
| I2C Clock
 
| GPIO_184(mode=4)<br>SAFE_MODE(mode=7)
 
| J1 connector<br>
 
|-
 
| 27
 
| GPIO185_I2C3_SDA
 
| I2C3_SDA(mode=0)
 
| I2C Data
 
| GPIO_185(mode=4)<br>SAFE_MODE(mode=7)
 
| J1 connector<br>
 
|}
 
 
 
<br>
 
 
 
=== Expansion connectors interfaces  ===
 
 
 
The IGEP MODULE has 2 connectors of 70-pin with up to 140 signals at 1V8 CMOS to suport lots of features provided by OMAP3 processor that can be used in your custom baseboard.
 
 
 
==== J1 connector  ====
 
 
 
{| cellspacing="1" cellpadding="1" border="1" style="width: 900px; height: 104px;"
 
|-
 
| Pad
 
| Connect to
 
| Main peripheral
 
| Main utility
 
| Other available peripherals
 
|
 
Share with
 
 
 
|-
 
| 1
 
| nRESET
 
| -
 
| Read Reset Omap
 
| -
 
| -
 
|-
 
| 2
 
| DSS_D1
 
| DSS_DATA1(mode=0)
 
| LCD pixel data bit
 
|
 
UART1_CTS(mode=2)<br><font color="red">DSSVENC656_DATA1(mode=3)</font><br>GPIO_71(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 3
 
| DSS_D0
 
| DSS_DATA0(mode=0)
 
| LCD pixel data bit
 
|
 
UART1_RTS(mode=2)<br><font color="red">DSSVENC656_DATA0(mode=3)</font><br>GPIO_70(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 4
 
| DSS_D3
 
| DSS_DATA3(mode=0)
 
| LCD pixel data bit
 
| <font color="red">DSSVENC656_DATA3(mode=3)</font><br>GPIO_73(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 5
 
| DSS_D5
 
| DSS_DATA5(mode=0)
 
| LCD pixel data bit
 
|
 
UART3_TX(mode=2)<br><font color="red">DSSVENC656_DATA5(mode=3)</font><br>GPIO_75(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 6
 
| DSS_D2
 
| DSS_DATA2(mode=0)
 
| LCD pixel data bit
 
| <font color="red">DSSVENC656_DATA2(mode=3)</font><br>GPIO_72(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 7
 
| DSS_D4
 
| DSS_DATA4(mode=0)
 
| LCD pixel data bit
 
|
 
UART3_RX(mode=2)<br><font color="red">DSSVENC656_DATA4(mode=3)</font><br>GPIO_74(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 8
 
| GPIO10_SYSCLK1
 
| SYS_CLKOUT1(mode=0)
 
| Configurable output clock1
 
| GPIO_10(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 9
 
| GPIO00_SYSnIRQ0
 
| SYS_NIRQ(mode=0)
 
| External interrupt
 
| GPIO_0(mode=4)<br>SAFE_MODE(mode=7)
 
| TPS65950:CONTROL
 
|-
 
| 10
 
| GPIO185_I2C3_SDA
 
| I2C3_SDA(mode=0)
 
| I2C3 Data
 
| GPIO_185(mode=4)<br>SAFE_MODE(mode=7)
 
| J5
 
|-
 
| 11
 
| DSS_D10
 
| DSS_DATA10(mode=0)
 
| LCD pixel data bit
 
| GPIO_80(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 12
 
| DSS_D11
 
| DSS_DATA11(mode=0)
 
| LCD pixel data bit
 
| GPIO_81(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 13
 
| GPIO184_I2C3_SCL
 
| I2C3_SCL(mode=0)
 
| I2C3 Clock
 
| GPIO_184(mode=0)<br>SAFE_MODE(mode=7)
 
| J5
 
|-
 
| 14
 
| GPIO186_SYSCLK2
 
| GPIO_186(mode=4)
 
| -
 
| SYS_CLKOUT2(mode=0)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 15
 
| DSS_D22
 
| DSS_DATA22(mode=0)
 
| LCD pixel data bit
 
|
 
MCSPI3_CS1(mode=2)<br>DSS_DATA4(mode=3)<br>GPIO_92(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 16
 
| GPIO147_GPT8_PWM
 
| SAFE_MODE(mode=7)
 
| -
 
|
 
UART2_RX(mode=0)<br>MCBSP3_FSX(mode=1)<br>gpt8_PWM_EVT(mode=2)<br>GPIO_147(mode=4)
 
 
 
| -
 
|-
 
| 17
 
| DSS_D13
 
| DSS_DATA13(mode=0)
 
| LCD pixel data bit
 
| GPIO_83(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 18
 
| GPIO144_GPT9_PWM
 
| UART2_CTS(mode=0)
 
| UART2 Clear to send
 
|
 
MCBSP3_DX(mode=1)<br>GPT9_PWM_EVT(mode=2)<br>GPIO_144(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 19
 
| DSS_D14
 
| DSS_DATA14(mode=0)
 
| LCD pixel data bit
 
| GPIO_84(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 20
 
| DSS_D15
 
| DSS_DATA15(mode=0)
 
| LCD pixel data bit
 
| GPIO_85(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 21
 
| GPIO146_GPT11_PWM
 
| SAFE_MODE(mode=7)
 
| -
 
|
 
UART2_TX(mode=0)<br>MCBSP3_CLKX(mode=1)<br>GPT11_PWM_EVT(mode=2)<br>GPIO_146(mode=4)
 
 
 
| -
 
|-
 
| 22
 
| GPIO163_IR_CTS3
 
| UART3_CTS(mode=0)
 
| UART3 Clear to send
 
| GPIO_163(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 23
 
| DSS_D21
 
| DSS_DATA21(mode=0)
 
| LCD pixel data bit
 
|
 
MCSPI3_CS0(mode=2)<br>DSS_DATA3(mode=3)<br>GPIO_91(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 24
 
| DSS_D17
 
| DSS_DATA17(mode=0)
 
| LCD pixel data bit
 
| GPIO_87(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 25
 
| DSS_D18
 
| DSS_DATA18(mode=0)
 
| LCD pixel data bit
 
|
 
MCSPI3_CLK(mode=2)<br>DSS_DATA0(mode=3)<br>GPIO_88(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 26
 
| GPIO166_IR_TXD3
 
| UART3_TX(mode=0)
 
| UART· transfer data
 
| GPIO_166(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 27
 
| DSS_D19
 
| DSS_DATA19(mode=0)
 
| LCD pixel data bit
 
|
 
MCSPI3_SIMO(mode=2)<br>DSS_DATA1(mode=3)<br>GPIO_89(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 28
 
| DSS_D9
 
| DSS_DATA9(mode=0)
 
| LCD pixel data bit
 
| GPIO_79(mode=4)<br><br>HW_DBG17(mode=5)SAFE_MODE(mode=7)
 
| -
 
|-
 
| 29
 
| DSS_D7
 
| DSS_DATA7(mode=0)
 
| LCD pixel data bit
 
|
 
UART1_RX(mode=2)<br><font color="red">DSSVENC656_DATA7(mode=3)</font><br>GPIO_77(mode=4)<br>HW_DBG15(mode=5)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 30
 
| DSS_D8
 
| DSS_DATA8(mode=0)
 
| LCD pixel data bit
 
| GPIO_78(mode=4)<br><br>HW_DBG16(mode=5)SAFE_MODE(mode=7)
 
| -
 
|-
 
| 31
 
| GPIO165_IR_RXD3
 
| UART3_RX(mode=0)
 
| UART· Receive data
 
| GPIO_165(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 32
 
| GPIO66_DSS_PCLK
 
| DSS_PCLK(mode=0)
 
| LCD Clock
 
| GPIO_66(mode=4)<br>HW_DBG12(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 33
 
| DSS_D6
 
| DSS_DATA6(mode=0)
 
| LCD pixel data bit
 
|
 
UART1_TX(mode=2)<br><font color="red">DSSVENC656_DATA6(mode=3)</font><br>GPIO_76(mode=4)<br>HW_DBG14(mode=5)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 34
 
| GPIO68_DSS_VSYNC
 
| DSS_VSYNC(mode=0)
 
| LCD vertical sync
 
| GPIO_68(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 35
 
| GPIO67_DSS_HSYNC
 
| DSS_SYNC(mode=0)
 
| LCD horitzontal sync
 
| GPIO_67(mode=4)<br>HW_DBG13(mode=5)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 36
 
| PMIC_USBOTG_DP
 
| -
 
| -
 
| -
 
| TPS65950:USB;OTG Connector
 
|-
 
| 37
 
| PMIC_USBOTG_DN
 
| -
 
| -
 
| -
 
| TPS65950:USB;OTG Connector
 
|-
 
| 38
 
| PMIC_AUXL
 
| -
 
| Auxiliary input left
 
| -
 
| TPS65950:AUX Input
 
|-
 
| 39
 
| PMIC_MIC_SUB_M
 
| -
 
| MIC
 
| -
 
| TPS65950:ANA_MIC
 
|-
 
| 40
 
| PMIC_ADCIN4
 
| -
 
| General purpouse analog input
 
| -
 
| TPS65950:MCPC
 
|-
 
| 41
 
| PMIC_AUXR
 
| -
 
| Auxiliary input right
 
| -
 
| TPS65950:AUX Input
 
|-
 
| 42
 
| PMIC_PWM0
 
| -
 
| PWM0
 
| -
 
| TPS65950:GPIO
 
|-
 
| 43
 
| GPIO69_DSS_ACBIAS
 
| DSS_ACBIAS(mode=0)
 
| LCD&nbsp;Control
 
| GPIO_69(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 44
 
| DSS_D16
 
| DSS_DATA16(mode=0)
 
| LCD pixel data bit
 
| GPIO_86(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 45
 
| DSS_D20
 
| DSS_DATA20(mode=0)
 
| LCD pixel data bit
 
|
 
MCSPI3_SOMI(mode=2)<br>DSS_DATA2(mode=3)<br>GPIO_90(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 46
 
| PMIC_USBOTG_ID
 
| -
 
| -
 
| -
 
| TPS65950:USB;OTG Connector
 
|-
 
| 47
 
| GPIO170_HDQ_1WIRE
 
| GPIO_170(mode=4)
 
| -
 
|
 
HDQ_SIO(mode=0)<br>SYS_ALTCLK(mode=1)<br>I2C2_SCCBE(mode=2)<br>I2C3_SCCBE(mode=3)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 48
 
| PMIC_ADCIN3
 
| -
 
| General purpouse analog input
 
| -
 
| TPS65950:MCPC
 
|-
 
| 49
 
| PMIC_PWM1
 
| -
 
| PWM1
 
| -
 
| TPS65950:MCPC
 
|-
 
| 50
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 51
 
| PMIC_ADCIN5
 
| -
 
| General purpouse analog input
 
| -
 
| TPS65950:MCPC
 
|-
 
| 52
 
| PMIC_VBACKUP
 
| -
 
| Backup Battery
 
| -
 
| TPS65950:Backup Battery
 
|-
 
| 53
 
| PMIC_ADCIN6
 
| -
 
| General purpouse analog input
 
| -
 
| TPS65950:MCPC
 
|-
 
| 54
 
| PMIC_USBOTG_VBUS
 
| -
 
| -
 
| -
 
| TPS65950:USB
 
|-
 
| 55
 
| GPIO145:GPT10_PWM
 
| UART2_RTS(mode=0)
 
| UART2 Ready to send
 
|
 
MCBSP3_DR(mode=1)<br>GPT10_PWM_EVT(mode=2)<br>GPIO_145(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 56
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 57
 
| PMIC_MIC_MAIN_M
 
| -
 
| MIC
 
| -
 
| TPS65950:ANA_MIC
 
|-
 
| 58
 
| PMIC_ADCIN2
 
| -
 
| -
 
| -
 
| TPS65950:ADC
 
|-
 
| 59
 
| J1_SYSEN
 
| REGEN
 
| Master/Slave control power TPS65950
 
| -
 
| Master/Slave control power TPS65950
 
|-
 
| 60
 
| DSS_D12
 
| DSS_DATA12(mode=0)
 
| LCD pixel data bit
 
| GPIO_82(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 61
 
| DSS_D23
 
| DSS_DATA23(mode=0)
 
| LCD pixel data bit
 
|
 
DSS_DATA5(mode=3)<br>GPIO_83(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 62
 
| GPIO15_MCSPI3_SOMI
 
| GPIO_15(mode=4)
 
| <br>
 
|
 
ETK_D1(mode=0)<br>MCSPI3_SOMI(mode=1)<br>HSUSB1_DATA1(mode=3)<br>MM1_TXSE0(mode5)<br><font color="red">HSUSB3_TLL_DATA1(mode=6)</font><br>HW_DBG3(mode=7)
 
 
 
| -
 
|-
 
| 63
 
| GPIO164_RTS3
 
| UART3_RTS(mode=0)
 
| UART· Ready to send
 
| GPIO_164(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 64
 
| PMIC_ADCIN7
 
| -
 
| General purpouse analog input
 
| -
 
| TPS65950:Headset
 
|-
 
| 65
 
| PMIC_PWRON
 
| -
 
| Battery control
 
| -
 
| TPS65950:Control
 
|-
 
| 66
 
| VBAT
 
| -
 
| Board supply: 3V5-4V2
 
| -
 
| -
 
|-
 
| 67
 
| VBAT
 
| -
 
| Board supply: 3V5-4V2
 
| -
 
| -
 
|-
 
| 68
 
| PMIC_HSOL
 
| -
 
| Headset output left
 
| -
 
| TPS65950:Headset
 
|-
 
| 69
 
| PMIC_HSOR
 
| -
 
| Headset output right
 
| -
 
| TPS65950:Headset
 
|-
 
| 70
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|}
 
 
 
<br>
 
 
 
==== J4 connector<br>  ====
 
 
 
{| cellspacing="1" cellpadding="1" border="1" style="width: 900px; height: 2880px;"
 
|-
 
| Pad
 
| Connect to
 
| Main peripheral
 
| Main utility
 
| Other available peripherals
 
|
 
Share with
 
 
 
|-
 
| 1
 
| VBAT
 
| -
 
| Board supply: 3V5-4V2
 
| -
 
| -<br>
 
|-
 
| 2
 
| VBAT
 
| -
 
| Board supply: 3V5-4V2
 
| -
 
| -<br>
 
|-
 
| 3
 
| GND
 
| -
 
| GND
 
| -
 
| -<br>
 
|-
 
| 4
 
| GPMC_nCS5
 
| GPMC_nCS5(mode=0)
 
| General purpose memory controller
 
|
 
SYS_NDMAREQ2(mode=1)<br>MCBSP4_DR(mode=2)<br>GPT10_PWM_EVT(mode=3)<br>GPIO_56(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -<br>
 
|-
 
| 5
 
| GPMC_nCS4
 
| GPMC_nCS4(mode=0)
 
| General purpose memory controller
 
|
 
SYS_NDMAREQ1(mode=1)<br>MCBSP4_CLKX(mode=2)<br>GPT9_PWM_EVT(mode=3)<br>GPIO_55(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -<br>
 
|-
 
| 6
 
| GPMC_nWE
 
| GPMC_nWE
 
| General purpose memory controller
 
| -
 
| -<br>
 
|-
 
| 7
 
| GPMC_nADV_ALE
 
| GPMC_nADV
 
| General purpose memory controller
 
| -
 
| -<br>
 
|-
 
| 8
 
| GPMC_nOE
 
| GPMC_nOE
 
| General purpose memory controller
 
| -
 
| -<br>
 
|-
 
| 9
 
| GPIO65_ETH1_IRQ1
 
| GPMC_WAIT3(mode=0)
 
| -
 
| SYS_NDMAREQ1(mode=1)<br><font color="blue">UART4_RX(mode=2)</font><br>GPIO_65(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 10
 
| GPIO64_ETH0_NRESET
 
| GPIO_64(mode=4)
 
| -
 
| GPMC_WAIT2(mode=0)<br><font color="blue">UART4_TX(mode=2)</font><br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 11
 
| GPMC_A2
 
| GPMC_A2(mode=0)
 
| General purpose memory controller
 
| GPIO_35(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 12
 
| GPMC_A8
 
| GPMC_A8(mode=0)
 
| General purpose memory controller
 
| GPIO_41(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 13
 
| GPMC_A5
 
| GPMC_A5(mode=0)
 
| General purpose memory controller
 
| GPIO_38(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 14
 
| GPMC_A7
 
| GPMC_A7(mode=0)
 
| General purpose memory controller
 
| GPIO_40(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 15
 
| GPMC_D2
 
| GPMC_D2
 
| General purpose memory controller
 
| -
 
| Used in the IGEP COM PROTON
 
|-
 
| 16
 
| GPMC_D10
 
| GPMC_D10(mode=0)
 
| General purpose memory controller
 
| GPIO_46(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 17
 
| GPMC_D3
 
| GPMC_D3
 
| General purpose memory controller
 
| -
 
| Used in the IGEP COM PROTON
 
|-
 
| 18
 
| GPMC_D11
 
| GPMC_D11(mode=0)
 
| General purpose memory controller
 
| GPIO_47(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 19
 
| GPMC_D4
 
| GPMC_D4
 
| General purpose memory controller
 
| -
 
| Used in the IGEP COM PROTON
 
|-
 
| 20
 
| GPMC_D12
 
| GPMC_D12(mode=0)
 
| General purpose memory controller
 
| GPIO_48(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 21
 
| GPMC_D5
 
| GPMC_D5
 
| General purpose memory controller
 
| -
 
| Used in the IGEP COM PROTON
 
|-
 
| 22
 
| GPMC_D15
 
| GPMC_D15(mode=0)
 
| General purpose memory controller
 
| GPIO_51(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 23
 
| GPIO13_MMC3_CMD
 
| GPIO_13(mode=4)
 
| -<br>
 
|
 
ETK_CTL(mode=0)<br>MMC3_CMD(mode=2)<br>HSUSB1_CLK(mode=3)<br><font color="red">HSUSB1_TLL_CLK(mode=6)</font><br>HW_DBG1(mode=7)
 
 
 
| -
 
|-
 
| 24
 
| GPIO148_TXD1
 
| UART1_TX(mode=0)
 
| Transmited serial UART
 
| GPIO_148(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 25
 
| GPIO176_SPI1_CS2
 
| GPIO_176(mode=4)
 
| -
 
|
 
MCSPI1_CS2(mode=0)<br>MMC3_CLK(mode=3)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 26
 
| GPIO18_MMC3_D0
 
| GPIO_18(mode=4)
 
| -
 
|
 
ETK_D4(mode=0)<br>MCBSP5_DR(mode=1)<br>MMC3_DAT0(mode=2)<br>HSUSB1_DATA4(mode=3)<br><font color="red">HSUSB1_TLLDATA4(mode=6)</font><br>HW_DBG6(mode=7)
 
 
 
| -
 
|-
 
| 27
 
| GPIO174_SPI1_CS2
 
| McSPI1_CS0(mode=0)
 
| Chip select 0
 
|
 
MMC2_DAT7(mode=1)<br>GPIO_174(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 28
 
| GPIO53_GPMC_nCS2
 
| GPIO_53(mode=4)
 
| -
 
| GPMC_NCS2(mode=0)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 29
 
| GPIO14_MMC3_D4
 
| GPIO_14(mode=4)
 
| -
 
|
 
ETK_D0(mode=0)<br>MCSPI3_SIMO(mode=1)<br>MMC3_DAT4(mode=2)<br>HSUSB1_DATA0(mode=3)<br>MM1_RXCV(mode=5)<br><font color="red">HSUSB1_TLL_DATA0(mode=6)</font><br>HW_DBG2(mode=7)
 
 
 
| -
 
|-
 
| 30
 
| GPIO21_MMC3_D7
 
| GPIO_21(mode=4)
 
| -
 
|
 
ETK_D7(mode=0)<br>MCSPI3_CS1(mode=1)<br>MMC3_DAT7(mode=2)<br>HSUSB1_DATA3(mode=3)<br>MM1_TXEN_N(mode=5)<br><font color="red">HSUSB1_TLL_DATA3(mode=6)</font><br>HW_DBG9(mode=7)
 
 
 
| -
 
|-
 
| 31
 
| GPIO17_MMC3_D3
 
| GPIO_17(mode=4)
 
| -
 
|
 
ETK_D3(mode=0)<br>MCSPI3_CLK(mode=1)<br>MMC3_DAT3(mode=2)<br>HSUSB1_DATA7(mode=3)<br><font color="red">HSUSB1_TLL_DATA7(mode=6)</font><br>HW_DBG5(mode=7)
 
 
 
| -
 
|-
 
| 32
 
| HUSBH_VBUS
 
| -
 
| USB2<br>
 
| -
 
| USB3326
 
|-
 
| 33
 
| GND
 
| -
 
| GND
 
| -
 
| -
 
|-
 
| 34
 
| HSUSB_DP
 
| -
 
| USB2
 
| -
 
| USB3326
 
|-
 
| 35
 
| HSUSB_DM
 
| -
 
| USB2
 
| -
 
| USB3326
 
|-
 
| 36
 
| GPIO19_MMC3_D1
 
| GPIO_19(mode=4)
 
| -<br>
 
|
 
ETK_D5(mode=0)<br>MCSPI5_FSX(mode=1)<br>MMC3_DAT1(mode=2)<br>HSUSB1_DATA5(mode=3)<br><font color="red">HSUSB1_TLL_DATA5(mode=6)</font><br>HW_DBG7(mode=7)
 
 
 
| -
 
|-
 
| 37
 
| GPIO22_MMC3_D6
 
| SYS_DRM_MSECURE(mode=1)
 
| -
 
|
 
ETK_D8(mode=0)<br>MMC3_DAT6(mode=2)<br>HSUSB1_DIR(mode=3)<br>GPIO_22(mode=4)<br><font color="red">HSUSB1_TLL_DIR(mode=6)</font><br>HW_DBG10(mode=7)
 
 
 
| -
 
|-
 
| 38
 
| GPIO23_MMC3_D5
 
| GPIO_23(mode=4)
 
| -<br>
 
|
 
ETK_D9(mode=0)<br>SYS_SECURE_INDICATOR(mode=1)<br>MMC3_DAT5(mode=2)<br>HSUSB1_NXT(mode=3)<br><font color="red">HSUSB1_TLL_NXT(mode=6)</font><br>HW_DBG11(mode=7)
 
 
 
| -
 
|-
 
| 39
 
| GPIO20_MMC3_D2
 
| GPIO_20(mode=4)
 
| -<br>
 
|
 
ETK_D6(mode=0)<br>MCBSP5_DX(mode=1)<br>MMC3_DAT2(mode=2)<br>HSUSB1_DATA6(mode=3)<br><font color="red">HSUSB1_TLL_DATA6(mode=6)</font><br>HW_DBG8(mode=7)
 
 
 
| -
 
|-
 
| 40
 
| GPIO12_MMC3_CLK
 
| GPIO_12(mode=4)
 
| -<br>
 
|
 
ETK_CLK(mode=0)<br>MCBSP5_CLKX(mode=1)<br>MMC3_CLK(mode=2)<br>HSUSB1_STP(mode=3)<br>MM1_RXDP(mode=5)<br><font color="red">HSUSB1_TLL_STP(mode=6)</font><br>HW_DBG0(mode=7)
 
 
 
| -
 
|-
 
| 41
 
| GPIO114_SPI1_NIRQ
 
| GPIO_114(mode=4)
 
| -
 
| SAFE_MODE(mode=7)
 
| -
 
|-
 
| 42
 
| GPIO175_SPI1_CS1
 
| GPIO_175(mode=4)
 
| -
 
|
 
MCSPI1_CS1(mode=0)<br>MMC3_CMD(mode=3)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 43
 
| GPIO171_SPI1_CLK
 
| McSPI1_CLK(mode=0)
 
| Clock<br>
 
|
 
MMC2_DAT4(mode=1)<br>GPIO_171(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 44
 
| GPIO172_SPI1_SIMO
 
| McSPI1_SIMO(mode=0)
 
| Slave input master output<br>
 
|
 
MMC2_DAT5(mode=1)<br>GPIO_172(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 45
 
| GPIO173_SPI1_SOMI
 
| McSPI1_SOMI(mode=0)
 
| Slave output master input<br>
 
|
 
MMC2_DAT6(mode=1)<br>GPIO_173(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 46
 
| GPIO149_MMC3_CD
 
| UART1_RTS(mode=0)
 
| Uart ready to send<br>
 
| GPIO_149(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 47
 
| GPIO150_MMC3_WP
 
| UART1_CTS(mode=0)
 
| Uart clear to send<br>
 
| GPIO_150(mode=4)<br><font color="red">HSUSB3_TLL_CLK(mode=6)</font><br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 48
 
| GPIO151_RXD1
 
| UART1_RX(mode=0)
 
| Received serial UART<br>
 
|
 
MCBSP1_CLKR(mode=2)<br>MCSPI4_CLK(mode=3)<br>GPIO_151(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 49
 
| GPMC_D7
 
| GPMC_D7
 
| General purpose memory controller
 
| -
 
| Used in the IGEP COM PROTON
 
|-
 
| 50
 
| GPMC_D14
 
| GPMC_D14(mode=0)
 
| General purpose memory controller
 
| GPIO_50(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 51
 
| GPMC_D6
 
| GPMC_D6
 
| General purpose memory controller
 
| -
 
| Used in the IGEP COM PROTON
 
|-
 
| 52
 
| GPMC_D13
 
| GPMC_D13(mode=0)
 
| General purpose memory controller
 
| GPIO_49(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 53
 
| GPMC_D1
 
| GPMC_D1
 
| General purpose memory controller
 
| -
 
| Used in the IGEP COM PROTON
 
|-
 
| 54
 
| GPMC_D8
 
| GPMC_D8(mode=0)
 
| General purpose memory controller
 
| GPIO_44(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 55
 
| GPMC_D9
 
| GPMC_D9(mode=0)
 
| General purpose memory controller
 
| GPIO_45(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 56
 
| GPMC_D0
 
| GPMC_D0
 
| General purpose memory controller
 
| -
 
| Used in the IGEP COM PROTON
 
|-
 
| 57
 
| GPMC_A6
 
| GPMC_A6(mode=0)
 
| General purpose memory controller
 
| GPIO_39(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 58
 
| GPMC_A1
 
| GPMC_A1(mode=0)
 
| General purpose memory controller
 
| GPIO_34(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 59
 
| GPMC_A3
 
| GPMC_A3(mode=0)
 
| General purpose memory controller
 
| GPIO_36(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 60
 
| GPMC_A10
 
| GPMC_A10(mode=0)
 
| General purpose memory controller
 
| SYS_NDMAREQ3(mode=1)<br>GPIO_43(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 61
 
| GPMC_A4
 
| GPMC_A4(mode=0)
 
| General purpose memory controller
 
| GPIO_37(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 62
 
| GPMC_A9
 
| GPMC_A9(mode=0)
 
| General purpose memory controller
 
| SYS_NDMAREQ2(mode=1)<br>GPIO_42(mode=4)<br>SAFE_MODE(mode=7)
 
| Used in the IGEP COM PROTON
 
|-
 
| 63
 
| GPMC_nWP
 
| GPMC_nWP(mode=0)
 
| General purpose memory controller
 
| GPIO_62(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 64
 
| GPMC_nCS1
 
| GPMC_nCS1(mode=0)
 
| General purpose memory controller
 
| GPIO_52(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 65
 
| GPMC_nBE0_CLE
 
| GPMC_nBE0(mode=0)
 
| General purpose memory controller
 
| GPIO_60(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 66
 
| GPMC_nCS0
 
| GPMC_nCS0
 
| General purpose memory controller
 
| -
 
| -
 
|-
 
| 67
 
| GPMC_nCS6
 
| GPMC_nCS6(mode=0)
 
| General purpose memory controller
 
|
 
MCBSP4_DX(mode=2)<br>GPT11_PWM_EVT(mode=3)<br>GPIO_57(mode=4)<br>SAFE_MODE(mode=7)
 
 
 
| -
 
|-
 
| 68
 
| GPMC_WAIT0
 
| GPMC_WAIT0(mode=0)
 
| General purpose memory controller
 
| -
 
| -
 
|-
 
| 69
 
| GPMC_nBE1
 
| GPMC_nBE1(mode=0)
 
| General purpose memory controller
 
| GPIO_61(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|-
 
| 70
 
| GPMC_CLK
 
| GPMC_CLK(mode=0)
 
| General purpose memory controller
 
| GPIO_59(mode=4)<br>SAFE_MODE(mode=7)
 
| -
 
|}
 
  
<br>
+
[[Category:Peripherals]]

Latest revision as of 13:55, 28 June 2013

Overview

This wiki has information about IGEP connectors, this article is based in Kernel 2.6.37.y and IGEP Xloader without expansion support. You can find more information in schematics and manuals.

Connectors

Information tables:

  • Pad number. See PCB.
  • "Pad Name" is a name used in schematics, usually it will be default peripheral name (mode=0)
  • IGEP Initial mode
  • Main utility
  • Other available peripherals. See this page for more information:

->Black: available in OMAP3530/DM3730

->Red: available in OMAP3530

->Blue: available in DM3730

  • "Share with", some pads are connected with external peripherals. See this page for more information


IGEPv2

IGEP0020 expansion connectors

Igepv2 rc photo2.jpg


J990 connector

Using this expansion connector you have access to McBSP1, McBSP3, I2C2, MMC2(8 bits), nReset and REGEN signals from OMAP Processor. The interface is at 1.8V on all signals. Only 1.8V CMOS levels are supported. Do not expose the header to 3.3V.

J990 connector is BeagleBoard compatible expansion connector. IGEPv2-NOWIFI board is fully compatible. Other IGEPv2 board versions need software configuration to disable wifi interface and others because of shared hardware lines. MMC2 interface is used by wifi module. McBSP3 interface is used by PCM TPS65950 interface.

See which versions have WIFI/BT combo available.

Pad Pad Name Initial mode Main utility Other available peripherals Share with
1 VIO 1V8 - Power 1v8 - -
2 DC 5V - Power 5v - -
3 MMC2_DAT7 GPIO_139(mode=4) Reset WIFI

MMC2_DAT7(mode=0)
MMC2_CLKIN(mode=1)
MMC3_DAT3(mode=3)
HSUSB3_TLL_NXT(mode=5)
MM3_RXDM(mode=6)
SAFE_MODE(mode=7)

WIFI/BT combo:WIFI
5 MMC2_DAT6 GPIO_138(mode=4) Power down WIFI

MMC2_DAT6(mode=0)
MMC2_DIR_CMD(mode=1)
CAM_SHUTTER(mode=2)
MMC3_DAT2(mode=3)
HSUSB3_TLL_DIR(mode=5)
SAFE_MODE(mode=7)

WIFI/BT combo:WIFI
7 MMC2_DAT5 GPIO_137(mode=4) Reset BT

MMC2_DAT5(mode=0)
MMC2_DIR_DAT1(mode=1)
CAM_GLOBAL_RESET(mode=2)
MMC3_DAT1(mode=3)
HSUSB3_TLL_STP(mode=5)
MM3_RXDP(mode=6)
SAFE_MODE(mode=7)

WIFI/BT combo:BT
9 MMC2_DAT4 GPIO136(mode=4) -

MMC2_DAT4(mode=0)
MMC_DIR_DAT0(mode=1)
MMC3_DAT0(mode=3)
SAFE_MODE(mode=7)

-
11 MMC2_DAT3 MMC2_DAT3(mode=0) Transfer data

McSPI3_CS0(mode=1)
GPIO_135(mode=4)
SAFE_MODE(mode=7)

WIFI/BT combo:WIFI
13 MMC2_DAT2 MMC2_DAT2(mode=0) Transfer data

McSPI3_CS1(mode=1)
GPIO_134(mode=4)
SAFE_MODE(mode=7)

WIFI/BT combo:WIFI
15 MMC2_DAT1 MMC2_DAT1(mode=0) Transfer data GPIO_133(mode=4)
SAFE_MODE(mode=7)
WIFI/BT combo:WIFI
17 MMC2_DAT0 MMC2_DAT0(mode=0) Transfer data

McSPI3_SOMI(mode=1)
GPIO_132(mode=4)
SAFE_MODE(mode=7)

WIFI/BT combo:WIFI
19 MMC2_CMD MMC2_CMD(mode=0) Control Wire for bus MMC2 (WIFI)

McSPI3_SIMO(mode=1)
GPIO_131(mode=4)
SAFE_MODE(mode=7)

WIFI/BT combo:WIFI
21 MMC2_CLK0 MMC2_CLK(mode=0) Clock for MMC2 (WIFI)

McSPI3_CLK(mode=1)
GPIO_130(mode=4)
SAFE_MODE(mode=7)

WIFI/BT combo:WIFI
4 MCBSP3_DX MCBSP3_DX (mode=0) Transmitted serial Data (BT audio)

UART2_CTS(mode=1)
GPIO_140(mode=4)
HSUSB3_TLL_D4(mode=5)
SAFE_MODE(mode=7)

TPS65950: PCM VSP
6 MCBSP3_CLKX MCBSP3_CLKX(mode=0) Transmitted serial Clock (BT audio)

UART2_TX(mode=1)
GPIO_142(mode=4)
HSUSB3_TLL_D6(mode=5)
SAFE_MODE(mode=7)

BT/TPS65950: PCM VSP
8 MCBSP3_FSX MCBSP3_FSX (mode=0) Transmited Frame Syncronisation (BT audio)

UART2_RX(mode=1)
GPIO_143(mode=4)
HSUSB3_TLL_D7(mode=5)
SAFE_MODE(mode=7)

BT/TPS65950: PCM VSP
10 MCBSP3_DR MCBSP3_DR (mode=0) Received Serial Data (BT audio) UART2_RTS(mode=1)
GPIO_141(mode=4)
HSUSB3_TLL_D5(mode=5)
SAFE_MODE(mode=7)
TPS65950: PCM VSP
12 MCBSP1_DX GPIO_158(mode=4) - MCBSP1_DX(mode=0)
McSPI4_SIMO(mode=1)
McBSP3_DX(mode=2)
SAFE_MODE(mode=7)
-
14 MCBSP1_CLKX GPIO_162(mode=4) - MCBSP1_CLKX(mode=0)
McBSP3_CLKX(mode=2)
SAFE_MODE(mode=7)
-
16 MCBSP1_FSX GPIO_161(mode=4) - MCBSP1_FSX(mode=0)
McSPI4_CS0(mode=1)
McBSP3_FSX(mode=2)
SAFE_MODE(mode=7)
-
18 MCBSP1_DR GPIO_159(mode=4) - MCBSP1_DR(mode=0)
McSPI4_SOMI(mode=1)
McBSP3_DR(mode=2)
SAFE_MODE(mode=7)
-
20 MCBSP1_CLKR GPIO_156(mode=4) - MCBSP1_CLKR(mode=0)
MCSPI4_CLK(mode=1)
SAFE_MODE(mode=7)
-
22 MCBSP1_FSR GPIO_157(mode=4) - MCBSP1_FSR(mode=0)
CAM_GLOBAL_RESET(mode=2)
SAFE_MODE(mode=7)
-
23 I2C2_SDA I2C2_SDA(mode=0) I2C2 Data GPIO_183(mode=4)
SAFE_MODE(mode=7)
CAM if configured via hardware: RC14
24 I2C2_SCL I2C2_SCL(mode=0) I2C2 Clock GPIO_168(mode=4)
SAFE_MODE(mode=7)
CAM if configured via hardware: RC13
25 REGEN - Master/Slave control power TPS65950 - -
26 nRESET - Read Reset Omap - -
27 GND - GND - -
28 GND - GND - -


J960 connector

This connector is used mainly to connect via serie to IGEP Software using RS232 standard.

On IGEPv2 revision B:

  • This J960 connector has only Debug RS232 interface
  • So, it is needed null modem configuration (direct connection between two computers). RX and TX lines are crossed in this null modem configuration between two equipments (TX1->RX2 / TX2->RX1).

On IGEPv2 revision C:

  • You should modify your serial debug cable in order not to damage your serial PC port. 
  • Additional RS232 port (UART1) on same J960 connector. It is only needed to  rotate 180o the IDC-10 (AT-Everex) to DB9 cable.
  • It has been added resistors for alternative UART1, UART2 and UART3 hardware selection.
  • See Schematics (RC) for more information.
Pad Pad Name Initial mode Main utility Other available peripherals (only via hardware)

Share with

1 - - - - -
2 RS232_RX2 UART3_RX(R966) Serial debug UART2_RX(R952) only RC SN65C3232EPW
3 RS232_TX2 UART3_TX(R965) Serial debug UART2_TX(R947) only RC SN65C3232EPW
4 - - - - -
5 GND - GND - -
6 GND - GND - -
7 - - - - -
8 RS232_TX1 UART1_TX(R961) - UART3_TX(R940) only RC SN65C3232EPW
9 RS232_RX1 UART1_RX(R962) - UART3_RX(R942) only RC SN65C3232EPW
10 - - - - -

SN65C3232EPW: IC RS232 LINE DVR/RCVR

J940 connector

This connector is used mainly to connect via RS485 (UART1) with other devices. User can use this connector to power the board with 5VDC. Use only 5V regulated DC. The IGEPv2 BOARD does not use this 9v power supply. Only on IGEPv2 revision B, the PWR_9V input is directly routed to JC01 and J971 connectors. On IGEPv2 revision C is not available.

Pad Pad Name Initial mode Main utility Other available peripherals Share with
1 PWR_GND GND - - -
2 PWR_5V Power 5v - - -
3 PWR_9V (Not connected) - - -
4 RS485_A UART3_RX/UART3_TX A aka '−' aka TxD-/RxD- aka inverting pin - TXS0102DCUR
5 RS485_B UART3_RX/UART3_TX B aka '+' aka TxD+/RxD+ aka non-inverting pin - TXS0102DCUR

TXS0102DCUR: Bidirectional voltage-level translator

J400 connector

J400 is used to JTAG (Joint Test Action Group). JTAG is a standardized serial protocol widely used in printed circuit boards. Its main functions are:

  • Debug the software of an embedded system directly
  • Storing firmware
  • Boundary scan testing

JTAG Suggested:

  • JTAG Debugger XDS510+ USB from Spectrum Digital with Code Composer Studio 3.3 or higher.
  • JTAG Debugger XD100v2 USB from Spectrum Digital with Code Composer Studio 4 or higher.
Pad Pad Name Initial mode Main utility Other available peripherals Share with
1 JTAG_TMS JTAG_TMS
- -
2 JTAG_NTRST JTAG_NTRST
- -
3 JTAG_TDI JTAG_TDI
- -
4 GND - GND - -
5 1V8 Power 1V8
- -
6 - -
- -
7 JTAG_TD0 JTAG_TD0
- -
8 GND - GND - -
9 JTAG_RTCK JTAG_RTCK
- -
10 GND - GND - -
11 JTAG_TCK JTAG_TCK
- -
12 GND - GND - -
13 JTAG_EMU0 JTAG_EMU0(mode=0)
GPIO_11(mode=4)
SAFE_MODE(mode=7)
-
14 JTAG_EMU1 JTAG_EMU1(mode=0)
GPIO_31(mode=4)
SAFE_MODE(mode=7)
-


J970 connector

J970 is used to implement a keypad, it is connected to TPS65950. The keypad interface controller provides an enhanced keypad decode capability and simultaneously reduces host processor software overhead. When a key button of the keyboard matrix is pressed the corresponding row and column lines are shorted together. To allow key press detection, all input pins (KBR) are pulled up to VCC and all output pins (KBC) driven to a low level. Any action on a button generates an interrupt to the sequencer. The decoding sequence is written to allow detection of simultaneous press actions on several key buttons.

More information in TPS65950 datasheets. TPS65950 send via I2C1 all the interrupt request.

  • Can handle up to 8 x 8 keypads, IGEPv2 can handle up to 4 x 4 keypads.
  • Optionally, you can decode via Omap software.
  • Event detection on key press and key release.
  • Multikey press detection, can detect up 2  keys at the same time.
  • Long-key detection on prolonged key press.
  • Programmable time-out on permanent key press or after keypad release.
Igep keypad.png
Pad Pad Name Initial mode Main utility Other available peripherals Share with
1 KPD_CO KPD_CO Keypad controler Column 0 - -
2 KPD_C1 KPD_C1 Keypad controler Column 1 - -
3 KPD_C2 KPD_C2 Keypad controler Column 2 - -
4 KPD_C3 KPD_C3 Keypad controler Column 3 - -
5 KPD_RO KPD_RO Keypad controler Row 0 - -
6 KPD_R1 KPD_R1 Keypad controler Row 1 - -
7 KPD_R2 KPD_R2 Keypad controler Row 2 - -
8 KPD_R3 KPD_R3 Keypad controler Row 3 - -



JC30 connector

These connectors allow the access to the Camera interface signals. Omap has the processing capability to connect RAW image-sensor modules via this connector.

Pad Pad Name Initial mode Main utility Other available peripherals Share with
1 CAM_HS GPIO_94(mode=4) - CAM_HS(mode=0)
HW_DBG0(mode=5)
SAFE_MODE(mode=7)
-
2 CAM_VS GPIO_95(mode=4) - CAM_VS(mode=0)
HW_DBG1(mode=5)
SAFE_MODE(mode=7)
-
3 CAM_XCLKA CAM_XCLKA(mode=0) Camera interface GPIO_96(mode=4)
SAFE_MODE(mode=7)
-
4 GND - GND - -
5 CAM_PCLK CAM_PCLK(mode=0) Camera interface GPIO_97(mode=4)
HW_DBG2(mode=5)
SAFE_MODE(mode=7)
-
6 GND - GND - -
7 CAM_DO GPIO_99(mode=4) - CAM_DO(mode=0)
SAFE_MODE(mode=7)
-
8 CAM_FLD GPIO_98(mode=4) - CAM_FLD(mode=0)
CAM_GLOBAL_RESET(mode=2)
HW_DBG3(mode=5)
SAFE_MODE(mode=7)
-
9 CAM_D2 CAM_D2(mode=0) Camera interface GPIO_101(mode=4)
HW_DBG4(mode=5)
SAFE_MODE(mode=7)
-
10 CAM_D1 GPIO_100(mode=4) - CAM_D1(mode=0)
SAFE_MODE(mode=7)
-
11 CAM_D4 CAM_D4(mode=0) Camera interface GPIO_103(mode=4)
HW_DBG6(mode=5)
SAFE_MODE(mode=7)
-
12 CAM_D3 CAM_D3(mode=0) Camera interface GPIO_102(mode=4)
HW_DBG5(mode=5)
SAFE_MODE(mode=7)
-
13 CAM_D6 GPIO_105(mode=4) - CAM-D6(mode=0)
SAFE_MODE(mode=7)
-
14 CAM_D5 CAM_D5(mode=0) Camera interface GPIO_104(mode=4)
HW_DBG7(mode=5)
SAFE_MODE(mode=7)
-
15 CAM_D8 GPIO_107(mode=4) - CAM_D8(mode=0)
SAFE_MODE(mode=7)
-
16 CAM_D7 GPIO_106(mode=4) - CAM_D7(mode=0)
SAFE_MODE(mode=7)
-
17 CAM_D10 CAM_D10(mode=0) Camera interface GPIO_109(mode=4)
HW_DBG8(mode=5)
SAFE_MODE(mode=7)
-
18 CAM_D9 GPIO_108(mode=4) - CAM_D9(mode=0)
SAFE_MODE(mode=7)
-
19 CAM_XCLKB CAM_XCLKB(mode=0) Camera interface GPIO_111(mode=4)
SAFE_MODE(mode=7)
-
20 CAM_D11 CAM_D11(mode=0) Camera interface GPIO_110(mode=4)
HW_DBG9(mode=5)
SAFE_MODE(mode=7)
-
21 GPIO_112/I2C2_SCL GPIO_112(RC11) - I2C2_SCL(RC13)
SAFE_MODE(mode=7)
-
22 GPIO_113/I2C2_SDA GPIO_113(RC12) - I2C2_SDA(RC14)
SAFE_MODE(mode=7)
-
23 CAM_RESET GPIO_114(mode=4)
SAFE_MODE(mode=7) -
24 CAM_PDN GPIO_115(mode=4)
SAFE_MODE(mode=7) -
25 CAM_STROBE CAM_STROBE(mode=0) Camera interface GPIO_126(mode=4)
HW_DBG11(mode=5)
SAFE_MODE(mode=7)
-
26 CAM_WEN GPIO_167(mode=4) - CAM_WEN(mode=0)
CAM_SHUTTER(mode=2)
HW_DBG10(mode=5)
SAFE_MODE(mode=7)
-
27 3V3 - Power 3V3 - -
28 3V3 - Power 3V3 - -


TFT CONNECTORS: JA41-JA42

These connectors allow the access to the LCD signals.The output signal is shared by HDMI-A

JA41 connector

JA41 is used for DVI (Digital Video Interface) data part.

IGEPv2 RB version:

  • Available only the first 20 pads

IGEPv2 RC version:

  • Available only the first 28 pads

IGEPv2 RG version:

  • Available all 30 pads
Pad Pad Name Initial mode Main utility Other available peripherals Share with
1 VIO 3V3 - Power 3v3 - -
2 GND - GND - -
3 DVI_DATA0 DSS_D0(mode=0) LCD pixel data bit

UART1_CTS(mode=2)
DSSVENC656_DATA0(mode=3)
GPIO_70(mode=4)
SAFE_MODE(mode=7)

TFP410
4 DVI_DATA1 DSS_D1(mode=0) LCD pixel data bit

UART1_RTS(mode=2)
DSSVENC656_DATA1(mode=3)
GPIO_71(mode=4)
SAFE_MODE(mode=7)

TFP410
5 DVI_DATA2 DSS_D2(mode=0) LCD pixel data bit DSSVENC656_DATA2(mode=3)
GPIO_72(mode=4)
SAFE_MODE(mode=7)
TFP410
6 DVI_DATA3 DSS_D3(mode=0) LCD pixel data bit DSSVENC656_DATA3(mode=3)
GPIO_73(mode=4)
SAFE_MODE(mode=7)
TFP410
7 DVI_DATA4 DSS_D4(mode=0) LCD pixel data bit

DSSVENC656_DATA4(mode=3)
UART3_RX(mode=2)
GPIO_74(mode=4)
SAFE_MODE(mode=7)

TFP410
8 DVI_DATA5 DSS_D5(mode=0) LCD pixel data bit

DSSVENC656_DATA5(mode=3)
UART3_TX(mode=2)
GPIO_75(mode=4)
SAFE_MODE(mode=7)

TFP410
9 DVI_DATA6 DSS_D6(mode=0) LCD pixel data bit

DSSVENC656_DATA6(mode=3)
UART1_TX(mode=2)
GPIO_76(mode=4)
HW_DBG14(mode=5)
SAFE_MODE(mode=7)

TFP410
10 DVI_DATA7 DSS_D7(mode=0) LCD pixel data bit

DSSVENC656_DATA7(mode=3)
UART1_RX(mode=2)
GPIO_77(mode=4)
HW_DBG15(mode=5)
SAFE_MODE(mode=7)

TFP410
11 DVI_DATA8 DSS_D8(mode=0) LCD pixel data bit GPIO_78(mode=4)
HW_DBG16(mode=5)
SAFE_MODE(mode=7)
TFP410
12 DVI_DATA9 DSS_D9(mode=0) LCD pixel data bit GPIO_79(mode=4)
HW_DBG17(mode=5)
SAFE_MODE(mode=7)
TFP410
13 DVI_DATA10 DSS_D10(mode=0) LCD pixel data bit GPIO_80(mode=4)
SAFE_MODE(mode=7)
TFP410
14 DVI_DATA11 DSS_D11(mode=0) LCD pixel data bit GPIO_81(mode=4)
SAFE_MODE(mode=7)
TFP410
15 DVI_DATA12 DSS_D12(mode=0) LCD pixel data bit GPIO_82(mode=4)
SAFE_MODE(mode=7)
TFP410
16 DVI_DATA13 DSS_D13(mode=0) LCD pixel data bit GPIO_83(mode=4)
SAFE_MODE(mode=7)
TFP410
17 DVI_DATA14 DSS_D14(mode=0) LCD pixel data bit GPIO_84(mode=4)
SAFE_MODE(mode=7)
TFP410
18 DVI_DATA15 DSS_D15(mode=0) LCD pixel data bit GPIO_85(mode=4)
SAFE_MODE(mode=7)
TFP410
19 DVI_DATA16 DSS_D16(mode=0) LCD pixel data bit GPIO_86(mode=4)
SAFE_MODE(mode=7)
TFP410
20 DVI_DATA17 DSS_D17(mode=0) LCD pixel data bit GPIO_87(mode=4)
SAFE_MODE(mode=7)
TFP410
21 DVI_DATA18 DSS_D18(mode=0) LCD pixel data bit

DSS_D0 (mode=3)
MCSPI3_CLK(mode=2)
GPIO_88(mode=4)
SAFE_MODE(mode=7)

TFP410
22 DVI_DATA19 DSS_D19(mode=0) LCD pixel data bit

DSS_1 (mode=3)
MCSPI3_SIMO(mode=2)
GPIO_89(mode=4)
SAFE_MODE(mode=7)

TFP410
23 DVI_DATA20 DSS_D20(mode=0) LCD pixel data bit

DSS_D2 (mode=3)
MCSPI3_SOMI(mode=2)
GPIO_90(mode=4)
SAFE_MODE(mode=7)

TFP410
24 DVI_DATA21 DSS_D21(mode=0) LCD pixel data bit

DSS_D3 (mode=3)
MCSPI3_CSO(mode=2)
GPIO_91(mode=4)
SAFE_MODE(mode=7)

TFP410
25 DVI_DATA22 DSS_D22(mode=0) LCD pixel data bit

DSS_D4 (mode=3)
MCSPI3_CS1(mode=2)
GPIO_92(mode=4)
SAFE_MODE(mode=7)

TFP410
26 DVI_DATA23 DSS_D23(mode=0) LCD pixel data bit

DSS_D5(mode=3)
GPIO_93(mode=4)
SAFE_MODE(mode=7)

TFP410
27 I2C3_SCL I2C3_SCL(mode=0) I2C3 Clock GPIO_184(mode=4)
SAFE_MODE(mode=7)
TXS0102DCUR
28 I2C3_SDA I2C3_SDA(mode=0) I2C3 Data GPIO_185(mode=4)
SAFE_MODE(mode=7)
TXS0102DCUR
29 GPMC_NCS7 GPT8_PWM_EVT(mode=3) PWM signal GPMC_NCS7(mode=0)
GPMC_IO_DIR(mode=1)
MCBSP4_FSX(mode=2)
GPIO_58(mode=4)
SAFE_MODE(mode=7)
-
30 MCSPI1_CS3 MCSPI1_CS3(mode=0) SPI1 Chip select 3 HSUSB2_TLL_DATA2(mode=2)
HSUSB2_DATA2(mode=3)
GPIO_177(mode=4)
MM2_TXDAT(mode=5)
SAFE_MODE(mode=7)
LBEP5CLWMC


TFP410: converts DVI signal to HDMI

TXS0102DCUR: Increse I2c3 voltage to 5V to read EDID information

LBEP5CLWMC: Wifi and Bluetooth chip on IGEP0020-RG

JA42 connector

JA42 is used for DVI (Digital Video Interface) control part, TouchScreen control and SPI1.

The current available on the DC_5V rail is limited to the available current that remains from the DC supply that is connected to the DC power jack on the board. Keep in mind that some of that power is needed by the USB Host power rail and if more power is needed for the expansion board, the main DC power supply current capability may need to be increased. All signals are 1.8V except the DVI_PUP which is a 3.3V signal. The 1.8V rail is for level translation only and should not be used to power circuitry on the board. The 3.3V rail also has limited capacity on the power as well. It is suggested that the 5V rail be used to generate the required voltages for an adapter card.


  • Note that only IGEPv2 RG version has all 22 pads available. Other boards have only first 20 pads available.


Pad Pad Name Initial mode Main utility Other available peripherals Share with
1 VIO 1V8 - Power 1v8 - -
2 SYS_BOOT5 GPIO_7(mode=4) Omap boot config

SYS_BOOT5(mode=0)
MMC2_DIR_DAT3(mode=1)
DSS_DATA22(mode=3)
SAFE_MODE(mode=7)

-
3 DC_5V - Power 5v - -
4 GND - GND - -
5 SYS_BOOT0 GPIO_2(mode=4) Omap boot config SYS_BOOT0(mode=0)
DSS_DATA18(mode=3)
SAFE_MODE(mode=7)
-
6 SYS_BOOT1 GPIO_3(mode=4) Omap boot config SYS_BOOT1(mode=0)
DSS_DATA19(mode=3)
SAFE_MODE(mode=7)
-
7 DVI_VSYNC DSS_VSYNC(mode=0) LCD vertical sync (Expansion) GPIO_68(mode=4)
SAFE_MODE(mode=7)
TFP410
8 DVI_HSYNC DSS_HSYNC(mode=0) LCD Horitzontal sync (Expansion) GPIO_67 (mode=4)
HW_DBG13(mode=5)
SAFE_MODE(mode=7)
TFP410
9 DVI_ACBIAS DSS_ACBIAS(mode=0) LCD Control (Expansion) GPIO_69(mode=4)
SAFE_MODE(mode=7)
TFP410
10 DVI_PUP GPIO_170(mode=4) Control signal for DVI controller (Expansion)

HDQ_SIO(mode=0)
SYS_ALTCLK(mode=1)
I2C2_SCCBE(mode=2)
I2C3_SCCBE(mode=3)
SAFE_MODE(mode=7)

TFP410
11 DVI_PCLK DSS_PCLK(mode=0) LCD clock (Expansion) GPIO_66(mode=4)
HW_DBG12(mode=5)
SAFE_MODE(mode=7)
TFP410
12 TS_nPEN_IRQ GPIO_175(mode=4) Touchscreen control (Expansion) McSPI1_CS1(mode=0)
MMC3_CMD(mode=3)
SAFE_MODE(mode=7)
-
13 LCD_QVGA/nVGA GPIO_154(mode=4) Touchscreen control (Expansion) McBSP4_DX(mode=0)
HSUSB3_TLL_DATA2(mode=5)
MM3_TXDAT(mode=6)
SAFE_MODE(mode=7)
-
14 LCD_ENVDD GPIO_153(mode=4) Touchscreen control (Expansion) McBSP4_DR(mode=0)
HSUSB3_TLL_DATA0(mode=5)
MM3_RXRCV(mode=6)
SAFE_MODE(mode=7)
-
15 LCD_RESB GPIO_155(mode=4) Touchscreen control (Expansion) McBSP4_FSX(mode=0)
HSUSB3_TLL_DATA3(mode=5)
MM3_TXEN_N(mode=6)
SAFE_MODE(mode=7)
-
16 LCD_INI GPIO_152(mode=4) Touchscreen control (Expansion) McBSP4_CLKX(mode=0)
HSUSB3_TLL_DATA1(mode=5)
MM3_TXSE0(mode=6)
SAFE_MODE(mode=7)
-
17 MCSPI1_CLK McSPI1_CLK(mode=0) Touchscreen control (Expansion)

MMC2_DAT4(mode=1)
GPIO_171(mode=4)
SAFE_MODE(mode=7)

-
18 MCSPI1_SIMO McSPI1_SIMO(mode=0) Touchscreen control (Expansion)

MMC2_DAT5(mode=1)
GPIO_172(mode=4)
SAFE_MODE(mode=7)

-
19 MCSPI1_CS0 McSPI1_CS0(mode=0) Touchscreen control (Expansion)

MMC2_DAT7(mode=1)
GPIO_174(mode=4)
SAFE_MODE(mode=7)

-
20 MCSPI1_SOMI McSPI1_SOMI(mode=0) Touchscreen control (Expansion)

MMC2_DAT6(mode=1)
GPIO_173(mode=4)
SAFE_MODE(mode=7)

-
21 GPMC_NCS7 GPT8_PWM_EVT(mode=3) PWM signal GPMC_NCS7(mode=0)
GPMC_IO_DIR(mode=1)
MCBSP4_FSX(mode=2)
GPIO_58(mode=4)
SAFE_MODE(mode=7)
-
22 MCSPI1_CS3 MCSPI1_CS3(mode=0) SPI1 Chip select 3 HSUSB2_TLL_DATA2(mode=2)
HSUSB2_DATA2(mode=3)
GPIO_177(mode=4)
MM2_TXDAT(mode=5)
SAFE_MODE(mode=7)
LBEP5CLWMC

TFP410: converts DVI signal to HDMI

LBEP5CLWMC: Wifi and Bluetooth chip on IGEP0020-RG


IGEP MODULE

IGEP0030 expansion connectors

Module description small.jpg


NOTE: By default, J7 connector is not mounted

J5 connector

OMAP3 processor family has Camera Image Signal Processing (ISP) interface. ISP interface could to be connecting to CCD and CMOS image sensors.

Detailed features of ISP are:

  • CCD and CMOS Imager Interface
  • Memory Data Input
  • BT.601/BT.656 Digital YCbCr 4:2:2 (8-/10-Bit) Interface
  • Glueless Interface to Common Video Decoders
  • Resize Images From 1/4x to 4x
  • Separate Horizontal/Vertical Control

The signals of connector J5 are connected directly to the processor.

Pad Pad Name Initial mode Main utility Other available peripherals Share with
1 GPIO94_CAM_HS CAM_HS(mode=0) LCD Horitzontal sync GPIO_94(mode=4)
HW_DBG0(mode=5)
SAFE_MODE(mode=7)
-
2 GPIO95_CAM_VS GPIO_95(mode=4 - xGPIO_95(mode=4)
HW_DBG1(mode=5)
SAFE_MODE(mode=7)
-
3 GPIO96_CAM_XCLKA CAM_XCLKA(mode=0) Camera interface GPIO_96(mode=4)
SAFE_MODE(mode=7)
-
4 GPIO97_CAM_PCLK CAM_PCLK(mode=0) Camera interface GPIO_97(mode=4)
HW_DBG2(mode=5)
SAFE_MODE(mode=7)
-
5 GPIO98_CAM_FLD GPIO_98(mode=4) - CAM_FLD(mode=0)
CAM_GLOBAL_RESET(mode=2)
HW_DBG3(mode=5)
SAFE_MODE(mode=7)
-
6 GPIO99_CAM_D0 CAM_D0(mode=0) Camera interface GPIO_99(mode=4)
SAFE_MODE(mode=7)
-
7 GPIO100_CAM_D1 CAM_D1(mode=0) Camera interface GPIO_100(mode=4)
SAFE_MODE(mode=7)
-
8 GPIO101_CAM_D2 CAM_D2(mode=0) Camera interface GPIO_101(mode=4)
HW_DBG4(mode=5)
SAFE_MODE(mode=7)
-
9 GPIO102_CAM_D3 CAM_D3(mode=0) Camera interface GPIO_102(mode=4)
HW_DBG5(mode=5)
SAFE_MODE(mode=7)
-
10 GPIO103_CAM_D4 CAM_D4(mode=0) Camera interface GPIO_103(mode=4)
HW_DBG6(mode=5)
SAFE_MODE(mode=7)
-
11 GPIO104_CAM_D5 CAM_D5(mode=0) Camera interface GPIO_104(mode=4)
HW_DBG7(mode=5)
SAFE_MODE(mode=7)
-
12 GPIO105_CAM_D6 CAM_D6(mode=0) Camera Interface GPIO_105(mode=4)
SAFE_MODE(mode=7)
-
13 GPIO106_CAM_D7 CAM_D7(mode=0) Camera interface GPIO_106(mode=4)
SAFE_MODE(mode=7)
-
14 GPIO107_CAM_D8 CAM_D8(mode=0) Camera interface GPIO_107(mode=4)
SAFE_MODE(mode=7)
-
15 GPIO108_CAM_D9 CAM_D9(mode=0) Camera interface GPIO_108(mode=4)
SAFE_MODE(mode=7)
-
16 GPIO109_CAM_D10 CAM_D10(mode=0) Camera interface GPIO_109(mode=4)
HW_DBG8(mode=5)
SAFE_MODE(mode=7)
-
17 GPIO110_CAM_D11 CAM_D11(mode=0) Camera interface GPIO_110(mode=4)
HW_DBG9(mode=5)
SAFE_MODE(mode=7)
-
18 GPIO111_CAM_XCLKB CAM_XCLKB(mode=0) Camera interface GPIO_111(mode=4)
SAFE_MODE(mode=7)
-
19 GPIO167_CAM_WEN GPIO_167(mode=4) - CAM_WEN(mode=0)
CAM_SHUTTER(mode=2)
HW_DBG10(mode=5)
SAFE_MODE(mode=7)
-
20 GPIO126_CAM_STROBE CAM_STROBE(mode=4) Camera interface GPIO_126(mode=4)
HW_DBG11(mode=5)
SAFE_MODE(mode=7)
-
21 VIO_1V8 - Power 1V8 - -
22 PMIC_SYSEN - Control Slave power ICs - TPS65950: CONTROL
23 GND - GND - -
24 VBAT - Board supply: 3V5-4V2 - -
25 GPIO63_CAM_IRQ GPMC_WAIT1(mode=0) - GPIO_63(mode=4)
SAFE_MODE(mode=7)
-
26 GPIO184_I2C3_SCL I2C3_SCL(mode=0) I2C Clock GPIO_184(mode=4)
SAFE_MODE(mode=7)
J1 connector
27 GPIO185_I2C3_SDA I2C3_SDA(mode=0) I2C Data GPIO_185(mode=4)
SAFE_MODE(mode=7)
J1 connector


Expansion connectors interfaces

The IGEP MODULE has 2 connectors of 70-pin with up to 140 signals at 1V8 CMOS to suport lots of features provided by OMAP3 processor that can be used in your custom baseboard.

J1 connector
Pad Pad Name Initial mode Main utility Other available peripherals Share with
1 nRESET - Read Reset Omap - -
2 DSS_D1 DSS_DATA1(mode=0) LCD pixel data bit UART1_CTS(mode=2)
DSSVENC656_DATA1(mode=3)
GPIO_71(mode=4)
SAFE_MODE(mode=7)
-
3 DSS_D0 DSS_DATA0(mode=0) LCD pixel data bit

UART1_RTS(mode=2)
DSSVENC656_DATA0(mode=3)
GPIO_70(mode=4)
SAFE_MODE(mode=7)

-
4 DSS_D3 DSS_DATA3(mode=0) LCD pixel data bit DSSVENC656_DATA3(mode=3)
GPIO_73(mode=4)
SAFE_MODE(mode=7)
-
5 DSS_D5 DSS_DATA5(mode=0) LCD pixel data bit

UART3_TX(mode=2)
DSSVENC656_DATA5(mode=3)
GPIO_75(mode=4)
SAFE_MODE(mode=7)

-
6 DSS_D2 DSS_DATA2(mode=0) LCD pixel data bit DSSVENC656_DATA2(mode=3)
GPIO_72(mode=4)
SAFE_MODE(mode=7)
-
7 DSS_D4 DSS_DATA4(mode=0) LCD pixel data bit

UART3_RX(mode=2)
DSSVENC656_DATA4(mode=3)
GPIO_74(mode=4)
SAFE_MODE(mode=7)

-
8 GPIO10_SYSCLK1 SYS_CLKOUT1(mode=0) Configurable output clock1 GPIO_10(mode=4)
SAFE_MODE(mode=7)
-
9 GPIO00_SYSnIRQ0 SYS_NIRQ(mode=0) External interrupt GPIO_0(mode=4)
SAFE_MODE(mode=7)
TPS65950:CONTROL
10 GPIO185_I2C3_SDA I2C3_SDA(mode=0) I2C3 Data GPIO_185(mode=4)
SAFE_MODE(mode=7)
J5 connector
11 DSS_D10 DSS_DATA10(mode=0) LCD pixel data bit GPIO_80(mode=4)
SAFE_MODE(mode=7)
-
12 DSS_D11 DSS_DATA11(mode=0) LCD pixel data bit GPIO_81(mode=4)
SAFE_MODE(mode=7)
-
13 GPIO184_I2C3_SCL I2C3_SCL(mode=0) I2C3 Clock GPIO_184(mode=0)
SAFE_MODE(mode=7)
J5 connector
14 GPIO186_SYSCLK2 GPIO_186(mode=4) - SYS_CLKOUT2(mode=0)
SAFE_MODE(mode=7)
-
15 DSS_D22 DSS_DATA22(mode=0) LCD pixel data bit

MCSPI3_CS1(mode=2)
DSS_DATA4(mode=3)
GPIO_92(mode=4)
SAFE_MODE(mode=7)

-
16 GPIO147_GPT8_PWM SAFE_MODE(mode=7) - UART2_RX(mode=0)
MCBSP3_FSX(mode=1)
gpt8_PWM_EVT(mode=2)
GPIO_147(mode=4)
-
17 DSS_D13 DSS_DATA13(mode=0) LCD pixel data bit GPIO_83(mode=4)
SAFE_MODE(mode=7)
-
18 GPIO144_GPT9_PWM UART2_CTS(mode=0) UART2 Clear to send MCBSP3_DX(mode=1)
GPT9_PWM_EVT(mode=2)
GPIO_144(mode=4)
SAFE_MODE(mode=7)
-
19 DSS_D14 DSS_DATA14(mode=0) LCD pixel data bit GPIO_84(mode=4)
SAFE_MODE(mode=7)
-
20 DSS_D15 DSS_DATA15(mode=0) LCD pixel data bit GPIO_85(mode=4)
SAFE_MODE(mode=7)
-
21 GPIO146_GPT11_PWM SAFE_MODE(mode=7) -

UART2_TX(mode=0)
MCBSP3_CLKX(mode=1)
GPT11_PWM_EVT(mode=2)
GPIO_146(mode=4)

-
22 GPIO163_IR_CTS3 UART3_CTS(mode=0) UART3 Clear to send GPIO_163(mode=4)
SAFE_MODE(mode=7)
-
23 DSS_D21 DSS_DATA21(mode=0) LCD pixel data bit MCSPI3_CS0(mode=2)
DSS_DATA3(mode=3)
GPIO_91(mode=4)
SAFE_MODE(mode=7)
-
24 DSS_D17 DSS_DATA17(mode=0) LCD pixel data bit GPIO_87(mode=4)
SAFE_MODE(mode=7)
-
25 DSS_D18 DSS_DATA18(mode=0) LCD pixel data bit MCSPI3_CLK(mode=2)
DSS_DATA0(mode=3)
GPIO_88(mode=4)
SAFE_MODE(mode=7)
-
26 GPIO166_IR_TXD3 UART3_TX(mode=0) UART· transfer data GPIO_166(mode=4)
SAFE_MODE(mode=7)
-
27 DSS_D19 DSS_DATA19(mode=0) LCD pixel data bit MCSPI3_SIMO(mode=2)
DSS_DATA1(mode=3)
GPIO_89(mode=4)
SAFE_MODE(mode=7)
-
28 DSS_D9 DSS_DATA9(mode=0) LCD pixel data bit GPIO_79(mode=4)

HW_DBG17(mode=5)SAFE_MODE(mode=7)
-
29 DSS_D7 DSS_DATA7(mode=0) LCD pixel data bit UART1_RX(mode=2)
DSSVENC656_DATA7(mode=3)
GPIO_77(mode=4)
HW_DBG15(mode=5)
SAFE_MODE(mode=7)
-
30 DSS_D8 DSS_DATA8(mode=0) LCD pixel data bit GPIO_78(mode=4)

HW_DBG16(mode=5)SAFE_MODE(mode=7)
-
31 GPIO165_IR_RXD3 UART3_RX(mode=0) UART· Receive data GPIO_165(mode=4)
SAFE_MODE(mode=7)
-
32 GPIO66_DSS_PCLK DSS_PCLK(mode=0) LCD Clock GPIO_66(mode=4)
HW_DBG12(mode=5)
SAFE_MODE(mode=7)
-
33 DSS_D6 DSS_DATA6(mode=0) LCD pixel data bit UART1_TX(mode=2)
DSSVENC656_DATA6(mode=3)
GPIO_76(mode=4)
HW_DBG14(mode=5)
SAFE_MODE(mode=7)
-
34 GPIO68_DSS_VSYNC DSS_VSYNC(mode=0) LCD vertical sync GPIO_68(mode=4)
SAFE_MODE(mode=7)
-
35 GPIO67_DSS_HSYNC DSS_SYNC(mode=0) LCD horitzontal sync GPIO_67(mode=4)
HW_DBG13(mode=5)
SAFE_MODE(mode=7)
-
36 PMIC_USBOTG_DP - - - TPS65950:USB;OTG Connector
37 PMIC_USBOTG_DN - - - TPS65950:USB;OTG Connector
38 PMIC_AUXL - Auxiliary input left - TPS65950:AUX Input
39 PMIC_MIC_SUB_M - MIC - TPS65950:ANA_MIC
40 PMIC_ADCIN4 - General purpouse analog input - TPS65950:MCPC
41 PMIC_AUXR - Auxiliary input right - TPS65950:AUX Input
42 PMIC_PWM0 - PWM0 - TPS65950:GPIO
43 GPIO69_DSS_ACBIAS DSS_ACBIAS(mode=0) LCD Control GPIO_69(mode=4)
SAFE_MODE(mode=7)
-
44 DSS_D16 DSS_DATA16(mode=0) LCD pixel data bit GPIO_86(mode=4)
SAFE_MODE(mode=7)
-
45 DSS_D20 DSS_DATA20(mode=0) LCD pixel data bit MCSPI3_SOMI(mode=2)
DSS_DATA2(mode=3)
GPIO_90(mode=4)
SAFE_MODE(mode=7)
-
46 PMIC_USBOTG_ID - - - TPS65950:USB;OTG Connector
47 GPIO170_HDQ_1WIRE GPIO_170(mode=4) - HDQ_SIO(mode=0)
SYS_ALTCLK(mode=1)
I2C2_SCCBE(mode=2)
I2C3_SCCBE(mode=3)
SAFE_MODE(mode=7)
-
48 PMIC_ADCIN3 - General purpouse analog input - TPS65950:MCPC
49 PMIC_PWM1 - PWM1 - TPS65950:MCPC
50 GND - GND - -
51 PMIC_ADCIN5 - General purpouse analog input - TPS65950:MCPC
52 PMIC_VBACKUP - Backup Battery - TPS65950:Backup Battery
53 PMIC_ADCIN6 - General purpouse analog input - TPS65950:MCPC
54 PMIC_USBOTG_VBUS - - - TPS65950:USB
55 GPIO145:GPT10_PWM UART2_RTS(mode=0) UART2 Ready to send

MCBSP3_DR(mode=1)
GPT10_PWM_EVT(mode=2)
GPIO_145(mode=4)
SAFE_MODE(mode=7)

-
56 GND - GND - -
57 PMIC_MIC_MAIN_M - MIC - TPS65950:ANA_MIC
58 PMIC_ADCIN2 - - - TPS65950:ADC
59 J1_SYSEN REGEN Master/Slave control power TPS65950 - -
60 DSS_D12 DSS_DATA12(mode=0) LCD pixel data bit GPIO_82(mode=4)
SAFE_MODE(mode=7)
-
61 DSS_D23 DSS_DATA23(mode=0) LCD pixel data bit DSS_DATA5(mode=3)
GPIO_83(mode=4)
SAFE_MODE(mode=7)
-
62 GPIO15_MCSPI3_SOMI GPIO_15(mode=4)
ETK_D1(mode=0)
MCSPI3_SOMI(mode=1)
HSUSB1_DATA1(mode=3)
MM1_TXSE0(mode5)
HSUSB3_TLL_DATA1(mode=6)
HW_DBG3(mode=7)
-
63 GPIO164_RTS3 UART3_RTS(mode=0) UART· Ready to send GPIO_164(mode=4)
SAFE_MODE(mode=7)
-
64 PMIC_ADCIN7 - General purpouse analog input - TPS65950:Headset
65 PMIC_PWRON - Battery control - TPS65950:Control
66 VBAT - Board supply: 3V5-4V2 - -
67 VBAT - Board supply: 3V5-4V2 - -
68 PMIC_HSOL - Headset output left - TPS65950:Headset
69 PMIC_HSOR - Headset output right - TPS65950:Headset
70 GND - GND - -


J4 connector
Pad Pad Name Initial mode Main utility Other available peripherals Share with
1 VBAT - Board supply: 3V5-4V2 - -
2 VBAT - Board supply: 3V5-4V2 - -
3 GND - GND - -
4 GPMC_nCS5 GPMC_nCS5(mode=0) General purpose memory controller SYS_NDMAREQ2(mode=1)
MCBSP4_DR(mode=2)
GPT10_PWM_EVT(mode=3)
GPIO_56(mode=4)
SAFE_MODE(mode=7)
-
5 GPMC_nCS4 GPMC_nCS4(mode=0) General purpose memory controller SYS_NDMAREQ1(mode=1)
MCBSP4_CLKX(mode=2)
GPT9_PWM_EVT(mode=3)
GPIO_55(mode=4)
SAFE_MODE(mode=7)
-
6 GPMC_nWE GPMC_nWE General purpose memory controller - -
7 GPMC_nADV_ALE GPMC_nADV General purpose memory controller - -
8 GPMC_nOE GPMC_nOE General purpose memory controller - -
9 GPIO65_ETH1_IRQ1 GPMC_WAIT3(mode=0) - SYS_NDMAREQ1(mode=1)
UART4_RX(mode=2)
GPIO_65(mode=4)
SAFE_MODE(mode=7)
-
10 GPIO64_ETH0_NRESET GPIO_64(mode=4) - GPMC_WAIT2(mode=0)
UART4_TX(mode=2)
SAFE_MODE(mode=7)
-
11 GPMC_A2 GPMC_A2(mode=0) General purpose memory controller GPIO_35(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
12 GPMC_A8 GPMC_A8(mode=0) General purpose memory controller GPIO_41(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
13 GPMC_A5 GPMC_A5(mode=0) General purpose memory controller GPIO_38(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
14 GPMC_A7 GPMC_A7(mode=0) General purpose memory controller GPIO_40(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
15 GPMC_D2 GPMC_D2 General purpose memory controller - Used in the IGEP COM PROTON
16 GPMC_D10 GPMC_D10(mode=0) General purpose memory controller GPIO_46(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
17 GPMC_D3 GPMC_D3 General purpose memory controller - Used in the IGEP COM PROTON
18 GPMC_D11 GPMC_D11(mode=0) General purpose memory controller GPIO_47(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
19 GPMC_D4 GPMC_D4 General purpose memory controller - Used in the IGEP COM PROTON
20 GPMC_D12 GPMC_D12(mode=0) General purpose memory controller GPIO_48(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
21 GPMC_D5 GPMC_D5 General purpose memory controller - Used in the IGEP COM PROTON
22 GPMC_D15 GPMC_D15(mode=0) General purpose memory controller GPIO_51(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
23 GPIO13_MMC3_CMD GPIO_13(mode=4) - ETK_CTL(mode=0)
MMC3_CMD(mode=2)
HSUSB1_CLK(mode=3)
HSUSB1_TLL_CLK(mode=6)
HW_DBG1(mode=7)
-
24 GPIO148_TXD1 UART1_TX(mode=0) Transmited serial UART GPIO_148(mode=4)
SAFE_MODE(mode=7)
-
25 GPIO176_SPI1_CS2 GPIO_176(mode=4) - MCSPI1_CS2(mode=0)
MMC3_CLK(mode=3)
SAFE_MODE(mode=7)
-
26 GPIO18_MMC3_D0 GPIO_18(mode=4) - ETK_D4(mode=0)
MCBSP5_DR(mode=1)
MMC3_DAT0(mode=2)
HSUSB1_DATA4(mode=3)
HSUSB1_TLLDATA4(mode=6)
HW_DBG6(mode=7)
-
27 GPIO174_SPI1_CS2 McSPI1_CS0(mode=0) Chip select 0 MMC2_DAT7(mode=1)
GPIO_174(mode=4)
SAFE_MODE(mode=7)
-
28 GPIO53_GPMC_nCS2 GPIO_53(mode=4) - GPMC_NCS2(mode=0)
SAFE_MODE(mode=7)
-
29 GPIO14_MMC3_D4 GPIO_14(mode=4) - ETK_D0(mode=0)
MCSPI3_SIMO(mode=1)
MMC3_DAT4(mode=2)
HSUSB1_DATA0(mode=3)
MM1_RXCV(mode=5)
HSUSB1_TLL_DATA0(mode=6)
HW_DBG2(mode=7)
-
30 GPIO21_MMC3_D7 GPIO_21(mode=4) - ETK_D7(mode=0)
MCSPI3_CS1(mode=1)
MMC3_DAT7(mode=2)
HSUSB1_DATA3(mode=3)
MM1_TXEN_N(mode=5)
HSUSB1_TLL_DATA3(mode=6)
HW_DBG9(mode=7)
-
31 GPIO17_MMC3_D3 GPIO_17(mode=4) - ETK_D3(mode=0)
MCSPI3_CLK(mode=1)
MMC3_DAT3(mode=2)
HSUSB1_DATA7(mode=3)
HSUSB1_TLL_DATA7(mode=6)
HW_DBG5(mode=7)
-
32 HUSBH_VBUS - USB2 - USB3326
33 GND - GND - -
34 HSUSB_DP - USB2 - USB3326
35 HSUSB_DM - USB2 - USB3326
36 GPIO19_MMC3_D1 GPIO_19(mode=4) - ETK_D5(mode=0)
MCSPI5_FSX(mode=1)
MMC3_DAT1(mode=2)
HSUSB1_DATA5(mode=3)
HSUSB1_TLL_DATA5(mode=6)
HW_DBG7(mode=7)
-
37 GPIO22_MMC3_D6 SYS_DRM_MSECURE(mode=1) - ETK_D8(mode=0)
MMC3_DAT6(mode=2)
HSUSB1_DIR(mode=3)
GPIO_22(mode=4)
HSUSB1_TLL_DIR(mode=6)
HW_DBG10(mode=7)
-
38 GPIO23_MMC3_D5 GPIO_23(mode=4) - ETK_D9(mode=0)
SYS_SECURE_INDICATOR(mode=1)
MMC3_DAT5(mode=2)
HSUSB1_NXT(mode=3)
HSUSB1_TLL_NXT(mode=6)
HW_DBG11(mode=7)
-
39 GPIO20_MMC3_D2 GPIO_20(mode=4) - ETK_D6(mode=0)
MCBSP5_DX(mode=1)
MMC3_DAT2(mode=2)
HSUSB1_DATA6(mode=3)
HSUSB1_TLL_DATA6(mode=6)
HW_DBG8(mode=7)
-
40 GPIO12_MMC3_CLK GPIO_12(mode=4) - ETK_CLK(mode=0)
MCBSP5_CLKX(mode=1)
MMC3_CLK(mode=2)
HSUSB1_STP(mode=3)
MM1_RXDP(mode=5)
HSUSB1_TLL_STP(mode=6)
HW_DBG0(mode=7)
-
41 GPIO114_SPI1_NIRQ GPIO_114(mode=4) - SAFE_MODE(mode=7) -
42 GPIO175_SPI1_CS1 GPIO_175(mode=4) - MCSPI1_CS1(mode=0)
MMC3_CMD(mode=3)
SAFE_MODE(mode=7)
-
43 GPIO171_SPI1_CLK McSPI1_CLK(mode=0) Clock

MMC2_DAT4(mode=1)
GPIO_171(mode=4)
SAFE_MODE(mode=7)

-
44 GPIO172_SPI1_SIMO McSPI1_SIMO(mode=0) Slave input master output
MMC2_DAT5(mode=1)
GPIO_172(mode=4)
SAFE_MODE(mode=7)
-
45 GPIO173_SPI1_SOMI McSPI1_SOMI(mode=0) Slave output master input
MMC2_DAT6(mode=1)
GPIO_173(mode=4)
SAFE_MODE(mode=7)
-
46 GPIO149_MMC3_CD UART1_RTS(mode=0) Uart ready to send GPIO_149(mode=4)
SAFE_MODE(mode=7)
-
47 GPIO150_MMC3_WP UART1_CTS(mode=0) Uart clear to send GPIO_150(mode=4)
HSUSB3_TLL_CLK(mode=6)
SAFE_MODE(mode=7)
-
48 GPIO151_RXD1 UART1_RX(mode=0) Received serial UART MCBSP1_CLKR(mode=2)
MCSPI4_CLK(mode=3)
GPIO_151(mode=4)
SAFE_MODE(mode=7)
-
49 GPMC_D7 GPMC_D7 General purpose memory controller - Used in the IGEP COM PROTON
50 GPMC_D14 GPMC_D14(mode=0) General purpose memory controller GPIO_50(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
51 GPMC_D6 GPMC_D6 General purpose memory controller - Used in the IGEP COM PROTON
52 GPMC_D13 GPMC_D13(mode=0) General purpose memory controller GPIO_49(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
53 GPMC_D1 GPMC_D1 General purpose memory controller - Used in the IGEP COM PROTON
54 GPMC_D8 GPMC_D8(mode=0) General purpose memory controller GPIO_44(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
55 GPMC_D9 GPMC_D9(mode=0) General purpose memory controller GPIO_45(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
56 GPMC_D0 GPMC_D0 General purpose memory controller - Used in the IGEP COM PROTON
57 GPMC_A6 GPMC_A6(mode=0) General purpose memory controller GPIO_39(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
58 GPMC_A1 GPMC_A1(mode=0) General purpose memory controller GPIO_34(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
59 GPMC_A3 GPMC_A3(mode=0) General purpose memory controller GPIO_36(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
60 GPMC_A10 GPMC_A10(mode=0) General purpose memory controller SYS_NDMAREQ3(mode=1)
GPIO_43(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
61 GPMC_A4 GPMC_A4(mode=0) General purpose memory controller GPIO_37(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
62 GPMC_A9 GPMC_A9(mode=0) General purpose memory controller SYS_NDMAREQ2(mode=1)
GPIO_42(mode=4)
SAFE_MODE(mode=7)
Used in the IGEP COM PROTON
63 GPMC_nWP GPMC_nWP(mode=0) General purpose memory controller GPIO_62(mode=4)
SAFE_MODE(mode=7)
-
64 GPMC_nCS1 GPMC_nCS1(mode=0) General purpose memory controller GPIO_52(mode=4)
SAFE_MODE(mode=7)
-
65 GPMC_nBE0_CLE GPMC_nBE0(mode=0) General purpose memory controller GPIO_60(mode=4)
SAFE_MODE(mode=7)
-
66 GPMC_nCS0 GPMC_nCS0 General purpose memory controller - -
67 GPMC_nCS6 GPMC_nCS6(mode=0) General purpose memory controller MCBSP4_DX(mode=2)
GPT11_PWM_EVT(mode=3)
GPIO_57(mode=4)
SAFE_MODE(mode=7)
-
68 GPMC_WAIT0 GPMC_WAIT0(mode=0) General purpose memory controller - -
69 GPMC_nBE1 GPMC_nBE1(mode=0) General purpose memory controller GPIO_61(mode=4)
SAFE_MODE(mode=7)
-
70 GPMC_CLK GPMC_CLK(mode=0) General purpose memory controller GPIO_59(mode=4)
SAFE_MODE(mode=7)
-

USB3326: Miniature Hi-Speed USB Transceiver