What can I do with IGEP PARIS

From IGEP - ISEE Wiki

Revision as of 16:52, 20 April 2012 by Albert (talk | contribs)

Jump to: navigation, search


If you have successfully completed the getting started guide for BASE0010, you can follow this first introduction about what can you do with this board:


How to get DVI output

By default the DVI is outputs 1024 x 768 @ 60Hz, so if your monitor support this resolution you'll see the desktop when board is up.

Unfortunately the capability to automatically set the display resolution to match your monitor isn't yet available. The simplest method to customize the display resolution is to set it using [[How do I edit my kernel command line | kernel command line]

The required arguments use the following pattern: omapfb.mode=<display>:<resolutionMR-bpp@refresh> omapdss.def_disp=<display> where:

For example:

omapdss.def_disp=dvi omapfb.mode=1024x768MR-16@60
omapdss.def_disp=dvi omapfb.mode=hd720-16@60

See also: How do I edit my kernel command line.

How to configure ethernet

There are two Ethernets on the BASE0010 board which can be used, for example if your access to the internet is via a route you can configure one of them with following command:

ifconfig eth0 up
udhcpc -i eth0

For second interface just change the eth0 device for eth1

How to get sound out (audio out)

The amplifiers for the headset output are disabled by default, so the first thing you'll do is enable these amplifiers with

amixer set -D hw:0 'Headset' 0dB
amixer set -D hw:0 'HeadsetL Mixer AudioL2' on
amixer set -D hw:0 'HeadsetR Mixer AudioR2' on

Then you can easily play a wav sound, for example

aplay sample.wav

How to get sound in (audio in)

You can record audio in with

arecord -t wav -c 2 -r 44100 -f S16_LE -v audio-in.wav

Following output is expected on console

Recording WAVE 'audio-in.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
Plug PCM: Hardware PCM card 0 'TWL4030' device 0 subdevice 0
Its setup is:
stream       : CAPTURE
access       : RW_INTERLEAVED
format       : S16_LE
subformat    : STD
channels     : 2
rate         : 44100
exact rate   : 44100 (44100/1)
msbits       : 16
buffer_size  : 32768
period_size  : 2048
period_time  : 46439
tick_time    : 7812
tstamp_mode  : NONE
period_step  : 1
sleep_min    : 0
avail_min    : 2048
xfer_align   : 2048
start_threshold  : 1
stop_threshold   : 32768
silence_threshold: 0
silence_size : 0
boundary     : 1073741824

When ever you think you want to stop just press CONTRL+C

How to get user button

There is one button on the BASE0010 board which can be used by the software for user interaction.

The kernel driver creates a device in /dev/input directory. To access to the button you will use the Linux Input Device subsystem. In Particular evdev, which is a generic input event interface. It passes the events generated in the kernel straight to the program, with timestamps. The event codes are the same on all architectures and are hardware independent.

For example, the test program evtest (evtest.c) listens on the /dev/input/event0 file descriptor, trying to read any events

evtest /dev/input/event0
Input driver version is 1.0.0
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "gpio-keys"
Supported events:
 Event type 0 (Sync)
 Event type 1 (Key)
   Event code 276 (ExtraBtn)
Testing ... (interrupt to exit)

If you'll press the button you'll see

Event: time 8354.388305, type 1 (Key), code 276 (ExtraBtn), value 0
Event: time 8354.388335, -------------- Report Sync ------------
Event: time 8354.573364, type 1 (Key), code 276 (ExtraBtn), value 1
Event: time 8354.573364, -------------- Report Sync ------------

For more information please read:

  1. linux-2.6/Documentation/input/input.txt
  2. linux-2.6/Documentation/input/input-programming.txt




You have successfully completed this chapter of the guide.


Continue this tutorial guide: 3/3 - Start developing under IGEP Technology
Igep forum.png If you have any question, don't ask to ask at the IGEP Community Forum or the IGEP Community Chat Irc.png