Difference between revisions of "Getting started with IGEPv2 EXPANSION"
From IGEP - ISEE Wiki
m |
|||
Line 36: | Line 36: | ||
= Mounting IGEPv2 EXPANSION = | = Mounting IGEPv2 EXPANSION = | ||
− | The | + | The IGEPv2 EXPANSION connects to IGEPv2 via 5 connectors of 10, 22, 28 and 30 pins located on both boards. First align the biggest 28 pin-connector gently press it until the other connectors insert into their corresponding connectors from the other board.<br> |
[[Image:Igep0022 before mount.jpg|left|307x250px]][[Image:Igep0022 igep0020 combo.jpg|right|404x270px]] | [[Image:Igep0022 before mount.jpg|left|307x250px]][[Image:Igep0022 igep0020 combo.jpg|right|404x270px]] | ||
Line 68: | Line 68: | ||
== Jumpers configuration<br> == | == Jumpers configuration<br> == | ||
− | Some | + | Some IGEPv2 EXPANSION may include three jumpers that correspond to:<br> |
<br> | <br> | ||
Line 95: | Line 95: | ||
<br> | <br> | ||
− | These jumpers are designed for test and lab purposes to force a specific device by hardware.<br>For a '''normal use''' of | + | These jumpers are designed for test and lab purposes to force a specific device by hardware.<br>For a '''normal use''' of IGEPv2 EXPANSION '''THESE JUMPERS SHOULD BE REMOVED''' from the board. |
== Serial port == | == Serial port == | ||
Line 103: | Line 103: | ||
== VGA monitor == | == VGA monitor == | ||
− | Connect a VGA monitor to | + | Connect a VGA monitor to IGEPv2 EXPANSION VGA connector.<br> |
== CAN bus == | == CAN bus == | ||
− | Connect any CAN bus device or network to the CAN bus connector of the | + | Connect any CAN bus device or network to the CAN bus connector of the IGEPv2 EXPANSION.<br> |
== SIM card reader == | == SIM card reader == | ||
− | A SIM card reader is provided with | + | A SIM card reader is provided with IGEPv2 EXPANSION. You may connect a SIM card to use the GSM/GPRS modem to make phone calls or to send SMS or to write and read data from it, etc. |
== GSM/GPRS antenna == | == GSM/GPRS antenna == | ||
Line 121: | Line 121: | ||
== TFT and Touchscreen == | == TFT and Touchscreen == | ||
− | + | IGEPv2 EXPANSION integrates a LCD backlight driver (Texas instruments TPS61081) and touch screen controller (Texas instruments TSC2046), 4-wire touch screen controller which supports a low-voltage I/O interface which can be directly connected to a SEIKO 7” LCD or to a POWERTIP 4.3” LCD. Use J301 connector for POWERTRIP 4.3" or use J302, J303 and J304 connector for SEIKO 7".<br> | |
[[Image:IGEP0022 PROTO RA DSC 0142.JPG|frame|center|571x417px]]<br> | [[Image:IGEP0022 PROTO RA DSC 0142.JPG|frame|center|571x417px]]<br> | ||
Line 127: | Line 127: | ||
== Composite video == | == Composite video == | ||
− | There are two composite video inputs via RCA connectors in | + | There are two composite video inputs via RCA connectors in IGEPv2 EXPANSION.<br> |
Line 137: | Line 137: | ||
[[Category:IGEP Technology Devices Guides]] | [[Category:IGEP Technology Devices Guides]] | ||
− | |||
[[Category:Work in progress]] | [[Category:Work in progress]] |
Revision as of 10:24, 4 June 2012
Getting started with IGEPv2 EXPANSION |
This page is a starting point for IGEPv2 EXPANSION. |
IGEPv2 EXPANSION
|
Overview | ||
1) Mounting IGEPv2 EXPANSION |
![]() |
This is a work in progress article! |
Mounting IGEPv2 EXPANSION
The IGEPv2 EXPANSION connects to IGEPv2 via 5 connectors of 10, 22, 28 and 30 pins located on both boards. First align the biggest 28 pin-connector gently press it until the other connectors insert into their corresponding connectors from the other board.
Adding peripherals
You can begin to add peripherals like Serial port, VGA monitor, CAN bus, a SIM card reader, TFT and Touchscreen and the S-Video connectors.
Jumpers configuration
Some IGEPv2 EXPANSION may include three jumpers that correspond to:
Jumper name |
Position on board |
---|---|
Telit GE865 GSM/GPRS Modem:
|
![]() |
MCP2515 CAN BUS:
|
![]() |
These jumpers are designed for test and lab purposes to force a specific device by hardware.
For a normal use of IGEPv2 EXPANSION THESE JUMPERS SHOULD BE REMOVED from the board.
Serial port
Connect a null modem DB9 male-male serial cable between the board and your host machine, use the serial debug port to communicate with the host machine: Using serial debug port to communicate
VGA monitor
Connect a VGA monitor to IGEPv2 EXPANSION VGA connector.
CAN bus
Connect any CAN bus device or network to the CAN bus connector of the IGEPv2 EXPANSION.
SIM card reader
A SIM card reader is provided with IGEPv2 EXPANSION. You may connect a SIM card to use the GSM/GPRS modem to make phone calls or to send SMS or to write and read data from it, etc.
GSM/GPRS antenna
Connect an external GSM/GPRS antenna to the J404 GSC connector.
TFT and Touchscreen
IGEPv2 EXPANSION integrates a LCD backlight driver (Texas instruments TPS61081) and touch screen controller (Texas instruments TSC2046), 4-wire touch screen controller which supports a low-voltage I/O interface which can be directly connected to a SEIKO 7” LCD or to a POWERTIP 4.3” LCD. Use J301 connector for POWERTRIP 4.3" or use J302, J303 and J304 connector for SEIKO 7".
Composite video
There are two composite video inputs via RCA connectors in IGEPv2 EXPANSION.