Difference between revisions of "What can I do with IGEP RADAR SENSOR ORION"
From IGEP - ISEE Wiki
| Line 429: | Line 429: | ||
[[Image:Table orion JC2.jpg]] | [[Image:Table orion JC2.jpg]] | ||
| − | = IGEP COM MODULE Expansion<br> = | + | = IGEP COM MODULE Expansion<br> = |
| − | 2 expansion connectors are needed to interface radar sensor ORION with processor board IGEP COM MODULE: JC3 & JC4 | + | 2 expansion connectors are needed to interface radar sensor ORION with processor board IGEP COM MODULE: JC3 & JC4 |
| + | <br> | ||
| + | == JC3 pin-out == | ||
| + | |||
| + | [[Image:Table orion JC3.jpg]] | ||
| + | |||
| + | == Expansion connector JC4 == | ||
| + | |||
| + | [[Image:Table orion JC4.jpg]] | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | = Applications = | ||
| + | |||
| + | You can see a complete list of applications of the radar sensor ORION on this link: | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | {{Template:Navigation/IGEP Technology Guides/What can I do/Ending}} | + | {{Template:Navigation/IGEP Technology Guides/What can I do/Ending}} |
| − | [[Category: | + | [[Category:IGEP_Technology_Devices_Guides]] |
Revision as of 16:46, 26 July 2013
|
|
Interfacing with the sensor
You can control the sensor and get IF signal directly or through included ADC by means of different expansion connectors:
Expansion connector-I
Expansion connector JC1 is intended for control and monitoring of internal radar sensor ORION signals.
JC1 pin-out
NOMENCLATURE
Function names marked with gray shading (1) indicates that are available only on demand
PIN: PIN NUMBER OF THE CONNECTOR. SUBINDEX MEANING:
o PW: Power Line
o DIG: CMOS DIGITAL SIGNAL PORT 1V8 LOGIC LEVELS
o DIG3: CMOS DIGITAL SIGNAL PORT 3V3 LOGIC LEVELS
o DIG5: CMOS DIGITAL SIGNAL PORT 5V LOGIC LEVELS
o ANA: ANALOG PORT
o NC: PIN NOT CONNECTED<span /><span lang="EN-US" style="mso-bidi-font-family: TimesNewRoman" />
o (L): ACTIVE LOW LEVEL
o (H): ACTIVE HIGH LEVEL
LEVEL: IS THE NOMINAL VOLTAGE LEVEL
MODE 0: IS THE MODE 0 function pin name of OMAP microcontroller
MAX: IS THE ABSOLUTE MAXIMUM ALLOWED VOLTAGE LEVEL ON THIS PIN (PERMANENT DAMAGE IF HIGHER VOLTAGE)
FUNCTION: DESCRIPTION OF PIN SIGNAL
o (1): ISEE INTERNAL USE TEST PIN. AVAILABLE ONLY ON DEMAND<span lang="EN-US" style="mso-bidi-font-family: TimesNewRoman" />
o (2): INPUT when power supply is applied to radar board. OUTPUT in other case.
IGEPv2 Expansion
A single expansion connector, JC2, is enough to adapt IGEPv2 processor board to the radar sensor ORION.
JC2 pin-out
IGEP COM MODULE Expansion
2 expansion connectors are needed to interface radar sensor ORION with processor board IGEP COM MODULE: JC3 & JC4
JC3 pin-out
Expansion connector JC4
Applications
You can see a complete list of applications of the radar sensor ORION on this link:
You have successfully completed this chapter of the guide.
|
|
If you have any question, don't ask to ask at the IGEP Community Forum or the IGEP Community Chat | 
|
