4,199
edits
Changes
m
=== IGEP Static IP ===Static IP is recommended because IGEP always has assigned 192.168.5.1 static IP. Use the following steps:==== Linux ====
Run the following commands:
sudo ifconfig eth0 down
sudo ifconfig eth0 192.168.5.10 up
'''NOTE:''' You should have the usbnet module available for your Linux kernel. On most distributions, this is the case by default. If this is not the case for your distribution, you will need to enable USB networking support in the kernel. If you build your own kernel then you want 'CDC Ethernet support' in USB Network adaptors. IGEP SDK Virtual Machine has this module enabled.
usb0 eth0:0 Link encap:Ethernet HWaddr 6608:cc00:f227:bead:510c:b6 ad inet addr:192.168.75.10 Bcast:1920.1680.70.255 0 Mask:255.255.255.0 inet6 addr: fe80::64cc:f2ff:febe:51b6/64 Scope:Link
RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:44 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2496 (2.4 KB) TX bytes:8794 (8.7 KB)...</pre> *Connect to IGEP device
jdoe@ubuntu ~ $ ssh root@192.168.7.1 The authenticity of host '192.168.7.1 (192.168.7.1)' can't be established. ECDSA key fingerprint is 80:be:2d:b6:fe:b1:09:c3:3b:ac:0f:1d:f2:43:f2:20. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '192.168.7.1' (ECDSA) to the list of known hosts. root@igep00x0:~# uname -a Linux igep00x0 2.6.37 #1 Thu Jul 19 09:07:47 CEST 2012 armv7l GNU/Linux root@igep00x0:~#=== Windows and MAC OSX ===
==== Windows and MAC OSX ===='''NOTE:''' you should use [[IGEP SDK Virtual Machine|IGEP SDK Virtual Machine]] but you can use these steps:
You should use [[IGEP SDK Virtual Machine|IGEP SDK Virtual Machine]] to develop under IGEP Technology'''Windows:'''
=== IGEP Dynamic IP ==='''MAC OSX:''' '''(Please contribute)'''
→Install Putty
== Configure Host PC==
'''NOTE:''' You don't need to configure anything if you use [http://labs.isee.biz/index.php/IGEP_SDK_Virtual_Machine IGEP SDK Virtual Machine]
If you are running Linux in your PC, open a Terminal session and set the IP of the Ethernet interface in which IGEP is connected (for example eth0):
*In the file /etc/network/interfaces, you should add:
<pre>iface usb0 eth0 inet dhcp</pre> *Plug an USB Type-A to USB Type-A mini cable between your host PC and the USB OTG from IGEP deviceiface eth0:0 inet staticaddress 192.168. Use a powered USB Hub if you use IGEP COM MODULE or PROTON Board5. 10*If you use IGEP SDK VM you need to attach the [http://labsnetmask 255.isee255.biz/index255.php0</IGEP_SDK_Virtual_Machine#Attach_removable_devices_to_Virtual_Machine removable device] RNDIS driver. pre>
*Type in a terminal:
<pre>sudo ifup usb0eth0:0</pre>
*Revise that:
<pre>jdoe@ubuntu ~ $ ifconfig
...
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
If you are running Windows in your PC, depending of your OS version and your configuration the steps might be slightly different:
# Close all the dialogs
== Connect to IGEP device ==
=== Install Putty ===
'''NOTE:''' You don't need install anything if you use [[IGEP SDK Virtual Machine|IGEP SDK Virtual Machine]].
Now you are ready to log into IGEP via its Ethernet interface. You just need a program with a SSH client.
http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html
Install and run using executable or using apt-get command (in Linux):<pre>sudo apt-get install putty </pre> === Run Putty. === It will look like this:
[[Image:Putty ssh.png|center]]
user:root
password: (no password for this user: press return)
=== Troubleshooting ===
==== WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! ====