4,199
edits
Changes
m
=== Overview ===
=== Requirements ===
=== Configure Host PC===== Linux ==='''NOTE:''' You don't need to configure anything if you use [http://labs.isee.biz/index.php/IGEP_SDK_Virtual_Machine IGEP SDK Virtual Machine]
==== If you are running Linux ====in your PC, open a Terminal session and set the IP of the Ethernet interface in which IGEP is connected (for example eth0):
'''NOTE:''' You should have the usbnet module available for your Linux kernel. On most distributions, this is the case by default. If this is not the case for your distribution, you will need to enable USB networking support in the kernel. If you build your own kernel then you want 'CDC Ethernet support' in USB Network adaptors. IGEP SDK Virtual Machine has this module enabled.
<section begin=USB_linux />
usb0 eth0:0 Link encap:Ethernet HWaddr 6608:cc00:f227:bead:510c:b6 ad inet addr:192.168.75.10 Bcast:1920.1680.70.255 0 Mask:255.255.255.0 inet6 addr: fe80::64cc:f2ff:febe:51b6/64 Scope:Link
RX packets...</pre> === Windows and MAC OSX === '''NOTE:14 errors''' you should use [[IGEP SDK Virtual Machine|IGEP SDK Virtual Machine]] but you can use these steps:0 dropped '''Windows:0 overruns''' If you are running Windows in your PC, depending of your OS version and your configuration the steps might be slightly different:0 frame:0 TX packets# Click the '''Start button''' and select the '''Control Panel'''# Go to '''Network configuration'''# Right click the interface where IGEP is connected (for example:44 errors:0 dropped:0 overruns:0 carrier:0Local Network) and select '''Propierties''' collisions:0 txqueuelen:1000 # Select the '''TCP/IP Internet Protocol''' configuration and click the '''Propierties button''' RX bytes:2496 # Set a static IP (2192.168.4 KB) TX bytes:8794 (85.7 KB10)and 255.255.255.</pre> 0 as network submask# Close all the dialogs *Connect to IGEP device'''MAC OSX:'''
jdoe@ubuntu ~ $ ssh root@192.168.7.1 The authenticity of host '192.168.7.1 (192.168.7.1)' can't be established. ECDSA key fingerprint is 80:be:2d:b6:fe:b1:09:c3:3b:ac:0f:1d:f2:43:f2:20. Are you sure you want to continue connecting (yes/noPlease contribute)? yes Warning: Permanently added '192.168.7.1' (ECDSA) to the list of known hosts. root@igep00x0:~# uname -a Linux igep00x0 2.6.37 #1 Thu Jul 19 09:07:47 CEST 2012 armv7l GNU/Linux root@igep00x0:~# <section end=USB_linux />'
=== Connect to IGEP device == === Install Putty ==='''NOTE:''' You don't need install anything if you use [[IGEP SDK Virtual Machine|IGEP SDK Virtual Machine]].
==== Troubleshooting ==== ===== WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! =====
===== NFS in root filesystem =====
Don't use NFS in root filesystem combined with USB Ethernet Gadget
=== Windows and MAC OSX<br> ===
You should use [[IGEP SDK Virtual Machine|IGEP SDK Virtual Machine]] to develop under IGEP Technology
== Configure ==
First of all, adjust the IP of your PC in order to be in the right subnet of IGEP, for example: 192.168.5.10
'' Linux: ''
'''NOTE:''' You don't need to configure anything if you use [http://labs.isee.biz/index.php/IGEP_SDK_Virtual_Machine IGEP SDK Virtual Machine]
If you are running Linux in your PC, open a Terminal session and set the IP of the Ethernet interface in which IGEP is connected (for example eth0):
Run the following commands:
sudo ifconfig eth0 down
sudo ifconfig eth0 192.168.5.10 up
'' Windows: ''
If you are running Windows in your PC, depending of your OS version and your configuration the steps might be slightly different:
# Click the '''Start button''' and select the '''Control Panel'''
# Go to '''Network configuration'''
# Right click the interface where IGEP is connected (for example: Local Network) and select '''Propierties'''
# Select the '''TCP/IP Internet Protocol''' configuration and click the '''Propierties button'''
# Set a static IP (192.168.5.10) and 255.255.255.0 as network submask
# Close all the dialogs
→Install Putty
{{Message/Information Message|title=|message= In this guide is used [[ IGEP firmware Yocto ]]}}
__TOC__
You can log into IGEP via many interfaces, such Serial, Wifi, USB-Ethernet Gadget, etc. In this tutorial we are going to connect to the board via its Ethernet interface. By default, all IGEP Processor boards have a static IP in their Ethernet interface which is 192.168.5.1 and dynamic IP address assigned via DHCP.
There are some requisites to follow this guide:
*Host PC
*In the file /etc/network/interfaces, you should add:
<pre>iface usb0 eth0 inet dhcp</pre> *Plug an USB Type-A to USB Type-A mini cable between your host PC and the USB OTG from IGEP deviceiface eth0:0 inet staticaddress 192.168. Use a powered USB Hub if you use IGEP COM MODULE or PROTON Board5. 10*If you use IGEP SDK VM you need to attach the [http://labsnetmask 255.isee255.biz/index255.php0</IGEP_SDK_Virtual_Machine#Attach_removable_devices_to_Virtual_Machine removable device] RNDIS driver. pre>
*Type in a terminal:
<pre>sudo ifup usb0eth0:0</pre>
*Revise that:
<pre>jdoe@ubuntu ~ $ ifconfig
...
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Now you are ready to log into IGEP via its Ethernet interface. You just need a program with a SSH client.
http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html
Install and run using executable or using apt-get command (in Linux):<pre>sudo apt-get install putty </pre> === Run Putty. === It will look like this:
[[Image:Putty ssh.png|center]]
user:root
password: (no password for this user: press return)
In the case of the SSH client in Linux, a changed host key results in the client refusing to connect and showing an remote host identification has changed error
To fix the problem edit your ~/.ssh/known_hosts and remove the line corresponding to this host.
[[Category:Ethernet]]