1,381
edits
Changes
From IGEP - ISEE Wiki
no edit summary
After that sync and eject the microsd card.
== First Time Boot the board<br> ==
Insert the microsd card in the IGEPv2 board (or IGEP COM Module / IGEP COM Proton)<br>
Plug the power cord and you should see a similar boot like this:<br><pre>IGEP-X-Loader 2.6.1-1 (Jun 6 2014 - 11:03:48)XLoader: Processor DM3730 - ES1.2XLoader: Memory Manufacturer: Micron (2c)XLoader: Configuration file igep.ini Loaded from MMCXLoader: kernel zImage loaded from MMC at 0x80008000 size = 3149692Uncompressing Linux... done, booting the kernel.[ 0.000000] Linux version 2.6.37 (root@mcaro-vm-u12) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #1 Thu Jun 5 19:12:04 CEST 2014[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache[ 0.000000] Machine: IGEP0020 board[ 0.000000] IGEP: Unknown buddy for IGEP0020 machine[ 0.000000] IGEP: buddy: Hardware rev. B[ 0.000000] Reserving 16777216 bytes SDRAM for VRAM[ 0.000000] Memory policy: ECC disabled, Data cache writeback[ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 105730[ 0.000000] Kernel command line: smsc911x.mac=0x2,0x98,0x12,0x2,0xf0,0x28 buddy=base0010 buddy.revision=B console=ttyO2,115200n8 mem=50M@0x80000000 mem=383M@0x88000000 boot_delay=0 nocompcache=1 omapfb.mode=dvi:hd720-16@60 omapfb.vrfb=y vram=16M smsc911x.mac0=0xb2,0xb0,0x14,0xb5,0xcd,0xde smsc911x.mac1=0xb2,0xb0,0x14,0xb5,0xcd,0xdf root=/dev/mmcblk0p2 rw rootwait[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)[ 0.000000] Memory: 50MB 366MB 1MB = 417MB total[ 0.000000] Memory: 416544k/416544k available, 26848k reserved, 0K highmem[ 0.000000] Virtual kernel memory layout:[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)[ 0.000000] vmalloc : 0xe0000000 - 0xf8000000 ( 384 MB)[ 0.000000] lowmem : 0xc0000000 - 0xdff00000 ( 511 MB)[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)[ 0.000000] .init : 0xc0008000 - 0xc003e000 ( 216 kB)[ 0.000000] .text : 0xc003e000 - 0xc05d2260 (5713 kB)[ 0.000000] .data : 0xc05d4000 - 0xc0620400 ( 305 kB)[ 0.000000] NR_IRQS:409[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/800 MHz[ 0.000000] Reprogramming SDRC clock to 400000000 Hz[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts[ 0.000000] Total of 96 interrupts on 1 active controller[ 0.000000] GPMC revision 5.0[ 0.000000] Trying to install interrupt handler for IRQ402[ 0.000000] Trying to install interrupt handler for IRQ403[ 0.000000] Trying to install interrupt handler for IRQ404[ 0.000000] Trying to install interrupt handler for IRQ405[ 0.000000] Trying to install interrupt handler for IRQ406[ 0.000000] Trying to install interrupt handler for IRQ407[ 0.000000] Trying to install interrupt handler for IRQ408[ 0.000000] Trying to install type control for IRQ409[ 0.000000] Trying to set irq flags for IRQ409[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz[ 0.000000] Console: colour dummy device 80x30[ 0.000000] Calibrating delay loop... 799.29 BogoMIPS (lpj=3121152)[ 0.000000] pid_max: default: 32768 minimum: 301[ 0.000000] Security Framework initialized[ 0.000000] Mount-cache hash table entries: 512[ 0.000000] CPU: Testing write buffer coherency: ok[ 0.000000] regulator: core version 0.5[ 0.000000] regulator: dummy:[ 0.000000] NET: Registered protocol family 16[ 0.000000] OMAP GPIO hardware version 2.5[ 0.000000] OMAP GPIO hardware version 2.5[ 0.000000] OMAP GPIO hardware version 2.5[ 0.000000] OMAP GPIO hardware version 2.5[ 0.000000] OMAP GPIO hardware version 2.5[ 0.000000] OMAP GPIO hardware version 2.5[ 0.000000] omap_mux_init: Add partition: #1: core, flags: 0[ 0.000000] IGEP: Hardware Rev. C[ 0.000000] IGEP: initializing NAND memory device[ 0.000000] GPMC CS0: cs_on : 0 ticks, 0 ns (was 0 ticks) 0 ns[ 0.000000] GPMC CS0: cs_rd_off : 8 ticks, 40 ns (was 7 ticks) 40 ns[ 0.000000] GPMC CS0: cs_wr_off : 8 ticks, 40 ns (was 7 ticks) 40 ns[ 0.000000] GPMC CS0: adv_on : 2 ticks, 10 ns (was 1 ticks) 10 ns[ 0.000000] GPMC CS0: adv_rd_off: 5 ticks, 25 ns (was 7 ticks) 25 ns[ 0.000000] GPMC CS0: adv_wr_off: 8 ticks, 40 ns (was 7 ticks) 40 ns[ 0.000000] GPMC CS0: oe_on : 2 ticks, 10 ns (was 0 ticks) 10 ns[ 0.000000] GPMC CS0: oe_off : 10 ticks, 50 ns (was 5 ticks) 50 ns[ 0.000000] GPMC CS0: we_on : 2 ticks, 10 ns (was 0 ticks) 10 ns[ 0.000000] GPMC CS0: we_off : 6 ticks, 30 ns (was 4 ticks) 30 ns[ 0.000000] GPMC CS0: rd_cycle : 9 ticks, 45 ns (was 7 ticks) 45 ns[ 0.000000] GPMC CS0: wr_cycle : 9 ticks, 45 ns (was 7 ticks) 45 ns[ 0.000000] GPMC CS0: access : 7 ticks, 35 ns (was 4 ticks) 35 ns[ 0.000000] GPMC CS0: page_burst_access: 0 ticks, 0 ns (was 0 ticks) 0 ns[ 0.000000] GPMC CS0: wr_data_mux_bus: 0 ticks, 0 ns (was 0 ticks) 0 ns[ 0.000000] GPMC CS0: wr_access : 7 ticks, 35 ns (was 5 ticks) 35 ns[ 0.000000] hw-breakpoint: debug architecture 0x4 unsupported.[ 0.000000] OMAP DMA hardware revision 5.0[ 0.015533] bio: create slab <bio-0> at 0[ 0.016418] regulator: VDD 3V3: 3300 mV normal[ 0.017547] SCSI subsystem initialized[ 0.019683] usbcore: registered new interface driver usbfs[ 0.019927] usbcore: registered new interface driver hub[ 0.020080] usbcore: registered new device driver usb[ 0.020904] omap_i2c omap_i2c.1: bus 1 rev4.0 at 2600 kHz[ 0.026947] twl4030: PIH (irq 7) chaining IRQs 368..375[ 0.026977] twl4030: power (irq 373) chaining IRQs 376..383[ 0.027374] twl4030: gpio (irq 368) chaining IRQs 384..401[ 0.030395] regulator: VUSB1V5: 1500 mV normal standby[ 0.030914] regulator: VUSB1V8: 1800 mV normal standby[ 0.031433] regulator: VUSB3V1: 3100 mV normal standby[ 0.032745] twl4030_usb twl4030_usb: Initialized TWL4030 USB module[ 0.035095] regulator: VIO: 1800 <--> 1850 mV at 1800 mV normal standby[ 0.035644] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby[ 0.036163] regulator: VDAC: 1800 mV normal standby[ 0.036926] regulator: VPLL2: 1800 mV normal standby[ 0.037139] omap_i2c omap_i2c.3: bus 3 rev4.0 at 100 kHz[ 0.038574] Advanced Linux Sound Architecture Driver Version 1.0.23.[ 0.039550] cfg80211: Calling CRDA to update world regulatory domain[ 0.040283] Switching to clocksource 32k_counter[ 0.055725] musb-hdrc: version 6.0, otg (peripheral+host), debug=0[ 0.055847] musb-hdrc musb-hdrc.0: dma type: dma-inventra[ 0.056121] musb-hdrc musb-hdrc.0: USB OTG mode controller at fa0ab000 using DMA, IRQ 92[ 0.056518] NET: Registered protocol family 2[ 0.056671] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)[ 0.057006] TCP established hash table entries: 16384 (order: 5, 131072 bytes)[ 0.057281] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)[ 0.057434] TCP: Hash tables configured (established 16384 bind 16384)[ 0.057434] TCP reno registered[ 0.057464] UDP hash table entries: 256 (order: 0, 4096 bytes)[ 0.057464] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)[ 0.057617] NET: Registered protocol family 1[ 0.057891] RPC: Registered udp transport module.[ 0.057891] RPC: Registered tcp transport module.[ 0.057891] RPC: Registered tcp NFSv4.1 backchannel transport module.[ 0.059387] omap-iommu omap-iommu.0: isp registered[ 0.060760] VFS: Disk quotas dquot_6.5.2[ 0.060821] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)[ 0.061614] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.061981] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.[ 0.062713] msgmni has been set to 813[ 0.063629] io scheduler noop registered (default)[ 0.063629] io scheduler deadline registered[ 0.063720] io scheduler cfq registered[ 0.126556] OMAP DSS rev 2.0[ 0.149932] OMAP RFBI rev 1.0[ 0.150024] OMAP DISPC rev 3.0[ 0.150054] OMAP VENC rev 2[ 0.150207] omapdss supply vdds_sdi not found, using dummy regulator[ 0.150268] OMAP DSI rev 1.0[ 0.479064] [drm] Initialized drm 1.1.0 20060810[ 0.479156] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0[ 0.479461] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1[ 0.479736] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2[ 1.278900] console [ttyO2] enabled[ 1.282836] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3[ 1.298645] brd: module loaded[ 1.305847] loop: module loaded[ 1.313385] mtdoops: mtd device (mtddev=name/number) must be supplied[ 1.320159] omap2-nand driver initializing[ 1.324554] ONFI flash detected[ 1.327941] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron )[ 1.334899] Creating 3 MTD partitions on "omap2-nand.0":[ 1.340484] 0x000000000000-0x000000080000 : "X-Loader"[ 1.347198] 0x000000080000-0x000000c80000 : "Boot"[ 1.355316] 0x000000c80000-0x000020000000 : "File System"[ 1.444915] OneNAND driver initializing[ 1.450134] smsc911x: Driver version 2008-10-21.[ 1.456176] smsc911x-mdio: probed[ 1.459716] eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=0:01, irq=-1)[ 1.468017] net eth0: MAC Address: 02:98:12:02:f0:28[ 1.473510] usbcore: registered new interface driver asix[ 1.479309] usbcore: registered new interface driver cdc_ether[ 1.485534] usbcore: registered new interface driver net1080[ 1.491577] usbcore: registered new interface driver cdc_subset[ 1.497894] usbcore: registered new interface driver zaurus[ 1.503875] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver[ 2.516967] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller[ 2.522979] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1[ 2.530914] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800[ 2.548278] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00[ 2.554382] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002[ 2.561492] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1[ 2.569091] usb usb1: Product: OMAP-EHCI Host Controller[ 2.574645] usb usb1: Manufacturer: Linux 2.6.37 ehci_hcd[ 2.580322] usb usb1: SerialNumber: ehci-omap.0[ 2.585754] hub 1-0:1.0: USB hub found[ 2.589721] hub 1-0:1.0: 3 ports detected[ 2.618713] Initializing USB Mass Storage driver...[ 2.624023] usbcore: registered new interface driver usb-storage[ 2.630310] USB Mass Storage support registered.[ 2.635314] usbcore: registered new interface driver libusual[ 2.641479] usbcore: registered new interface driver usbtest[ 2.647460] g_ether gadget: using random self ethernet address[ 2.653594] g_ether gadget: using random host ethernet address[ 2.660156] usb0: MAC 1e:21:86:54:df:94[ 2.664184] usb0: HOST MAC ee:e7:b8:33:5f:64[ 2.668701] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008[ 2.675659] g_ether gadget: g_ether ready[ 2.679840] musb-hdrc musb-hdrc.0: MUSB HDRC host driver[ 2.685455] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2[ 2.693267] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002[ 2.700408] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1[ 2.707977] usb usb2: Product: MUSB HDRC host driver[ 2.713165] usb usb2: Manufacturer: Linux 2.6.37 musb-hcd[ 2.718811] usb usb2: SerialNumber: musb-hdrc.0[ 2.724243] hub 2-0:1.0: USB hub found[ 2.728210] hub 2-0:1.0: 1 port detected[ 2.733245] mice: PS/2 mouse device common for all mice[ 2.739440] input: TWL4030 Keypad as /devices/platform/omap/omap_i2c.1/i2c-1/1-004a/twl4030_keypad/input/input0[ 2.752593] input: twl4030_pwrbutton as /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1[ 2.764526] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0[ 2.771179] twl_rtc twl_rtc: Power up reset detected.[ 2.776702] twl_rtc twl_rtc: Enabling TWL-RTC.[ 2.781738] i2c /dev entries driver[ 2.786224] Linux media interface: v0.10[ 2.790496] Linux video capture interface: v2.00[ 2.795593] usbcore: registered new interface driver uvcvideo[ 2.801635] USB Video Class driver (v1.0.0)[ 2.806396] cpuidle: using governor ladder[ 2.810668] cpuidle: using governor menu[ 2.815917] mmci-omap-hs.0 supply vmmc_aux not found, using dummy regulator[ 2.824218] mmci-omap-hs.1 supply vmmc_aux not found, using dummy regulator[ 2.834289] omap_sham_mod_init: loading omap-sham driver[ 2.839874] omap_sham_mod_init: Unsupported cpu[ 2.844604] omap_aes_mod_init: loading omap-aes driver[ 2.850006] omap_aes_mod_init: Unsupported cpu[ 2.855194] usbcore: registered new interface driver usbhid[ 2.861053] usbhid: USB HID core driver[ 2.867004] IGEP SoC init[ 2.964752] asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok[ 2.974548] ALSA device list:[ 2.977630] #0: igep[ 2.980316] TCP cubic registered[ 2.983703] Initializing XFRM netlink socket[ 2.988220] NET: Registered protocol family 17[ 2.992889] NET: Registered protocol family 15[ 2.997589] L2TP core driver, V2.0[ 3.001159] lib80211: common routines for IEEE802.11 drivers[ 3.007110] Registering the dns_resolver key type[ 3.012054] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3[ 3.020385] ThumbEE CPU extension supported.[ 3.030426] Power Management for TI OMAP3.[ 3.036315] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized[ 3.044464] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized[ 3.052734] SmartReflex Class3 initialized[ 3.059509] clock: disabling unused clocks to save power[ 3.086303] Console: switching to colour frame buffer device 160x45[ 3.103881] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)[ 3.112396] omap_vout omap_vout: Buffer Size = 3686400[ 3.118682] omap_vout omap_vout: : registered and initialized video device 0[ 3.126068] omap_vout omap_vout: Buffer Size = 3686400[ 3.132324] omap_vout omap_vout: : registered and initialized video device 1[ 3.140197] Waiting for root device /dev/mmcblk0p2...[ 3.212158] mmc0: host does not support reading read-only switch. assuming write-enable.[ 3.236083] mmc0: new high speed SDHC card at address b368[ 3.242156] mmcblk0: mmc0:b368 USD 3.75 GiB[ 3.248413] mmcblk0: p1 p2[ 3.342407] mmc1: new SDIO card at address 0001[ 3.361755] EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)[ 3.372009] EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)[ 3.435180] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)[ 3.443664] VFS: Mounted root (ext4 filesystem) on device 179:2.[ 3.449981] Freeing init memory: 216Kmodprobe: FATAL: Could not load /lib/modules/2.6.37/modules.dep: No such file or directory
modprobe: FATAL: Could not load /lib/modules/2.6.37/modules.dep: No such file or directory * Loading cpufreq kernel modules... [ OK ] * CPU0... [ OK ] * CPUFreq Utilities: Setting ondemand CPUFreq governor... Ubuntu 12.04.4 LTS igep00x0 ttyO2 igep00x0 login: <br/pre>
== After first boot ==
