<section begin=IGEPv2 /><section begin=IGEP_COM_MODULE /><section begin=IGEP_COM_PROTON />{{Message/Information Message|title=TITLE|message=This How-To was tested with an Ubuntu 10.04 host machineIGEP SDK Virtual Machine, but most of the contents are valid also for other GNU/Linux distributions.There is no guarantee that this will work on other distributionsones.}}
Start session in a Linux PC. The first thing you'll do is download latest firwmare from the ISEE site.''Create IGEP Firmware bootable SD-card''' <br>
Download it '''IGEP AM335x''' - The first thing you'll do is download the latest firwmare from [http://www.isee.biz/support/downloads/item/igep-firmware-yocto-1-4-2-0-am335x ISEE site Yocto IGEP AM335x] <br>'''IGEP OMAP 3''' - Start session in IGEP SDK Virtual Machine. The first thing you'll do is download the Software latest firwmare from [http:/ /www.isee.biz/support/downloads/item/igep-firmware-yocto-1-2-2-6 ISEE site Yocto IGEP Firmware section of your boardOMAP 3] <br>'''IGEP SMARC i.MX6 Dual/Quad''' - The first thing you'll do is download the latest firwmare from [http://downloads.isee.biz/pub/releases/firmware/igep_firmware-yocto-1.8-0-imx6q-igep0046.tar.bz2 ISEE site Yocto IGEP SMARC i.MX6 Dual/Quad] <br>'''IGEP SMARC i.MX6 DualLite''' - The first thing you'll do is download the latest firwmare from [http://downloads.isee.biz/pub/releases/firmware/igep_firmware-yocto-1.8-0-imx6dl-igep0046.tar.bz2 ISEE site Yocto IGEP SMARC i.MX6 DualLite] <br>'''IGEP SMARC i.MX6 Solo''' - The first thing you'll do is download the latest firwmare from [http://downloads.isee.biz/pub/releases/firmware/igep_firmware-yocto-1.8-0-imx6s-igep0046.tar.bz2 ISEE site Yocto IGEP SMARC i.MX6 Solo] <br>
<section begin=IGEPv2 /> http://www.isee.biz/products/processor-boards/igepv2-board for IGEPv2<section end=IGEPv2 /><section begin=IGEP_COM_MODULE /> http://www.isee.biz/products/processor-boards/igep-com-module for IGEP COM MODULE<section end=IGEP_COM_MODULE /><section begin=IGEP_COM_PROTON /> http://www.isee.biz/products/processor-boards/igep-com-proton for IGEP COM PROTON<section end=IGEP_COM_PROTON /br>
Next, open a Terminal to untar the firmware you have just donwloaded and enter to the directory:#Select Products -> Processor Boards #Click on your processor board product. #Click on Software tab #Click on IGEP Firmware #Select Download icon.
Once the file is downloaded you can create bootable SD-Card, under Linux, untar the IGEP <pre>tar xzf pokyjxf igep_firmware-firmwareyocto-3.3.1-11*.tar.gzbz2 cd pokyigep_firmware-yocto-*</pre> Insert a SD-Card media and use the igep-media-create script to copy the firmwareto SD-3Card media.3<pre>.1/igep-media-create -–mmc <mmc> -11-image <image file> --machine <machine></pre> where:<br><mmc> - is the SD-Card device of your computer.<br><image file> - is the file that contains bootloader, kernel and rootfs image.<br><machine> - is the IGEP Processor Board. Available options are:
Insert your SD card into the host machine (the machine you downloaded the firmware), and run following command*igep0020 - For IGEP v2 Processor Board *igep0030 - For IGEP COM MODULE Processor Board *igep0032 - For IGEP COM PROTON Processor Board*igep0033 - For IGEP COM AQUILA Processor Board*igep0046 - For IGEP iMX6 Processor Board
./poky-media-create --mmc [device] --binary poky-image-sato-igep00x0-[timestamp].tar.gz --machine [machine]
where:* [device] is For example, assuming the SD -card device nametakes '/dev/sdf' and you have an IGEPv2 board ('igep0020'), for example: type<br> <pre>./igep-media-create --mmc /dev/sdb* [timestamp] is the timestamp of sdf --machine igep0020 --image demo-image-sato-igep00x0.tar.gz filebz2</pre> * [machine] is For example, assuming the machine nameSD-card device takes '/dev/sdb' and you have an IGEP COM MODULE ('igep0030'), options aretype<br> ** igep0020** <pre>./igep-media-create --mmc /dev/sdb --machine igep0030--image demo-image-sato-igep00x0.tar.bz2</pre> ** igep0032These methods should give you a bootable SD-card. <br>
Finally plug the MicroSD card into IGEP Processor Board and power up your board.<br>
'''Booting IGEP device and login/connect methods''' Insert the bootable SD-card media into the micro-SD card socket of IGEP device and power on it. This should result in a running system with Sato graphical desktop root filesystem built by Yocto. If you want login in/connect to the system, you have several options: <section end=IGEPv2 br> *'''Serial debug link''', you should just plug serial cable to your computer<br> *'''Ethernet''', you should assign an IP in the range 192.168.5.[2-254] and connect to target using a SSH client and connecting to 192.168.5.1 <br> *'''Wifi''', connect to IGEP_xx network, a dynamic IP should be assigned in your host and you can sign into the target connecting to 192.168.6.1 <br> *'''USB ethernet gadget''', connect a IGEP device to USB port of your computer, dynamic IP should be assigned in your host and you can sign into the target connecting to 192.168.7.1 o (if available) Graphical interface on plugged DVI/TFT display and USB Keyboard in IGEP device The root password is empty, so to log in type ''''root'''' for the user name and hit 'Enter' at the Password prompt: (''empty password'') and you should be in. <br> Then, you could play and fun with IGEP board. For example, you could flash the latest software image into internal FLASH memory ( [http://labs.isee.biz/index.php/How_to_flash_the_latest_software_image How to flash the latest software image] ) <section end=IGEP_COM_MODULE /br> <section end=IGEP_COM_PROTON br> {{Message/>Forum}} [[Category:Software]] [[Category:Boot_loaders]] [[Category:Software_distributions]] [[Category:Linux_Kernel]]
