Changes

{{Message/Information Message|title=TITLE|message=This How-To was tested with an Ubuntu 10.04 host machineIGEP SDK Virtual Machine, but most of the contents are valid also for other GNU/Linux distributions.There is no guarantee that this will work on other distributionsones.}}

<section begin=IGEPv2 /><section begin=IGEP_COM_MODULE /br><section begin=IGEP_COM_PROTON />Start session in a Linux PC. The first thing you'll do is download latest firwmare from the ISEE site. Download it from the Software / IGEP Firmware section of your board:  <br>

<section begin=IGEPv2 /br><section begin=IGEP_COM_MODULE /><section begin=IGEP_COM_PROTON />Next, we will use the application 'tar' to untar (uncompress) the downloaded file.

Next, we will use the application 'tar' to untar (uncompress) the downloaded file.  Open a Terminal session and go to the directory where you have your downloaded file. Then type:

Next, you can enter the extracted directory:

Now, lets create the MicroSD card with the latest firmware. Before it, you have to know '''Create a which 'device' is the MicroSD Cardlisted in the /dev/ directory''', a directory where the detected devices are listed by the Linux system.

Now, lets create the MicroSD card with the latest firmware. Before it, you have to know To '''which 'know the device' is the MicroSD listed in the /dev/ directoryname''', a directory where the detected devices are listed by the Linux system.follow this instructions:

To '''know the device nameInsert your MicroSD card''', follow this instructions:into the Linux host machine (the machine where you have downloaded the firmware).

'''Insert your MicroSD card''' into the Linux host machine (the machine where you have downloaded the firmware). In your Terminal session, run the following '''system command''':

This instruction will prompt all the '''system traces'''. If your MicroSD card has actually been detected by the system, '''the last lines of that prompt''' will correspond to the MicroSD card detection and mounting.

Check the '''MicroSD name and path''', for example: /dev/sdb and remember it.

Now you can '''run the following script''' in the directory you have just extracted, and you will have to add some parameters. In your Terminal session, type:

where: * '''[device]''' is the SD card device name, for example: /dev/sdb* '''[timestamp]''' the parameter --binary is actually the name of another .tar.gz compressed file that you have already extracted in the previous steps. If you want to auto-complete the [timestamp] parameter, press TAB in the ''timestamp'' when writing the instruction and the system will write the name of the file automatically.* '''[machine]''' is the machine name, options are:<section end=IGEPv2 /><section end=IGEP_COM_MODULE /><section end=IGEP_COM_PROTON /><section begin=IGEPv2 />** igep0020 , for IGEPv2<section end=IGEPv2 /><section begin=IGEP_COM_MODULE />** igep0030 , for IGEP COM MODULE<section end=IGEP_COM_MODULE /><section begin=IGEP_COM_PROTON />** igep0032 , for IGEP COM PROTON<section end=IGEP_COM_PROTON /> <section begin=IGEPv2 /><section begin=IGEP_COM_MODULE /br><section begin=IGEP_COM_PROTON />This instruction will last a few minutes. When the process ends, you will have a '''MicroSD card with the latest software''' on it.

Finally plug the MicroSD card into IGEP Processor Board and power up your board.

<section end=IGEPv2 /><section end=IGEP_COM_MODULE /><section end=IGEP_COM_PROTON /br>

[[Category:Software]][[Category:Boot loadersBoot_loaders]][[Category:Software distributionsSoftware_distributions]][[Category:Linux KernelLinux_Kernel]]