__NOTOC__{{Table/IGEP Technology Devices|Tech_Family={{#lst:Template:Links|IGEPv2_Tech_Family}}|Tech_ID={{#lst:Template:Links|IGEPv2_Tech_ID}}|Name={{#lst:Template:Links|IGEPv2_Name}}|Image={{#lst:Template:Links|IGEPv2_Image}}|ISEE_MainPage={{#lst:Template:Links|IGEPv2_ISEE_MainPage}}|ISEE_Hardware={{#lst:Template:Links|IGEPv2_ISEE_Hardware}}}}
{{Navigation/IGEP Technology Guides|device=IGEP0020}}
__TOC__
{| cellspacing="0" cellpaddingRequirements="5" border="1" align="center" width="100%" style="text-align: left;"|-| bgcolor="#cccccc" |'''Getting started with IGEP0020'''|-|'''This page is a starting point for all products of In this tutorial we are going to use the IGEP0020 family such IGEPv2 Board.'''|}following peripherals:
* IGEPv2 with its power supply
* Monitor compatible with DVI-D
* HDMI/DVI-D cable
* Network cable
* Powered USB HUB 2.0
* USB keyboard and a mouse
* PC
{| cellspacing="0" cellpaddingGetting started="5" border="1" align="center" style="text-align: left;"|-| bgcolor="#cccccc" colspan="3" | '''Overview'''|-| [[Image:Igep0020The following video illustrates the getting started process.jpg|250px|center|link=Category:IGEP0020]] |-|1) '''Connect a DVI Monitor'''|-|2) '''Connect a Serial cable'''|-|3) '''Connect Audio In/Out minijack'''|-|4) '''Connect USB devices (keyboard You will see how to connect some peripherals and mouse)'''|- |5) '''Connect network cable'''|-|6) '''Power power up IGEP0020 (5V DC)'''|}the board.
<div style="text-align: center;">
{{#ev:youtube|jtHL6JVo7kA|500}}
</div>
==Monitor==
The board will connect to your DVI monitor via its HDMI connector. You can use a HDMI/DVI-D cable to connect the board to the monitor. Your monitor should be able to support 1024 x 768 @ 60 Hz, which is the default resolution used by the firmware.
This first chapter describes '''how to boot IGEP020''If your monitor doesn' t have a DVI-D input, you can also use a HDMI input using a HDMI/HDMI cable, in that case you should [[How_do_I_edit_my_kernel_command_line | edit the kernel cmdline parameters]] and also gives some '''basic instructions''' about how to connect some peripherals.replace :
omapfb.mode=dvi:1280x720MR-16@60
=== Setting up ===----First of all, you can begin to '''add some peripherals'''.for this one :
In this tutorial we are going to use omapfb.mode=dvi:hd720-16@60
* ==Network==You may now plug the serial Ethernet cable* a monitor* a USB keyboard and a mouse* a into the 10/100 Ethernet jack of the board to get network cableaccess. The default firmware configures the Ethernet device with static ip address (192.168.5.1).
Do NOT power up your ==Keyboard/Mouse==The USB Host of the board yetis ONLY USB High speed (480Mbit/s). You will need a powered USB hub 2.0 to connect to most USB devices.
Now, connect an USB hub to the USB Host and plug your keyboard and mouse into the hub.
{| cellspacing="0" cellpadding="5" borderBooting="1" align="center" width="100%" style="text-align: left;"|-| bgcolor="#cccccc" |'''Monitor'''|-|IGEP0020 has a '''DVI-D interface''' where you can connect a '''HDMI connector to a monitor'''With all the peripherals attached, plug in the wall adapter (5V DC) and power on your board.You will need see a cable with '''male DVI-D connector''' for the monitorfew lights flash, see how to red leds light up and '''male HDMI connector''' from IGEP0020after a few seconds may light up only a fixed green led. The sequence will be different based on software version.|}
The Digital Visual Interface (DVI) "Under the hood" the bootloader is a video standard interface designed preparing to provide very high visual quality on digital display devices such as flat panel LCD computer displays load the linux kernel. The linux kernel loads and digital projectorsinitializes the hardware and mounts the root file system. It is partially compatible with Finally, you will see a screen desktop like the High-Definition Multimedia Interface (HDMI) standard in digital mode (DVI-D), and VGA in analog mode (DVI-A)following screenshot.
The pre-installed firmware in its flash memory consists of a minimal Linux-based distribution with a lite X Window System and GNOME Mobile based applications created with Poky Platform Builder.
Note that your monitor should be able You can use the mouse and the keyboard to support 1024 x 768 @ 60 Hz, which is the default resolution in dive into the preinstalled softwaredesktop.
[[Image:Poky-screenshot.png|thumb|center|500px|Screenshot of the Desktop of the pre-installed software]]
{| cellspacing="0" cellpadding="5" border="1" align="center" widthRemote connection via Ethernet="100%" style="text-align: left;"{{Message/Information Message|-title=| bgcolormessage="#cccccc" |'''Serial'''|-|Connect an 'If you aren''AT/Everex Cable''' to the '''10-pin serial header''' on IGEP0020 and t using a '''Linux operating system, use [http://enlabs.wikipediaisee.orgbiz/wikiindex.php/Null_modem null modemIGEP_SDK_Virtual_Machine IGEP SDK Virtual Machine] DB9 male-male''' serial cable between to connect to the board and your host machine.|}}
In the preinstalled softwareyour Host Machine, the serial port is configured as open a '''Debug terminal sessions set up an Ethernet alias for your network interface'''. ,
You can use the debug interface to interact with the IGEP Processor operating system [host] by typing commands in a client machine (your PC, for example) to perform specific tasks $ sudo ifconfig eth0:0 192. You can communicate and open a debug session via many interfaces such Serial port, Ethernet, Wifi, USB Ethernet Gadget, etc168.5.10
Furthermore, if you connect an external device Connect to the serial port you will be able to see the '''Linux Kernel traces''', as board using the system boots.SSH protocol
Therefore, you will be able to access IGEP0020 with a '''serial console''' from your client device (for example, a PC with Linux, Windows, etc $ ssh root@192.)168.5.1
[[Image:DSC 0177.JPG|thumb|550px|right|'''Serial''': AT/Everex Cable connected An empty password for root user should work to access to the 10-pin serial header on IGEP0020shell prompt. '''Network''': Ethernet cable]]
To communicate with IGEP0020 via Serial port you have to '''connect your client machine to the serial debug port''' in your IGEP0020 (host). {{Navigation/IGEP Technology Guides/Getting Started/Ending|Next_Step={{#lst:Template:Links|IGEPv2_Community_Guides_2}}}}
Once you have set the cable, then you have to run a serial console, or any program that can interact with the serial port in your host machine, such Minicom, PuTTy (Linux, Windows), Terminal (Windows), etc. * If you don't know how to set up your serial cable, refer to the following article: '''[[How_to_setup_the_IDC10_cable|How to setup the IDC10 cable]]'''. Also, if you do not have Serial port in your host machine you might need a USB to Serial converter to communicate via this port. * If you are not familiar with a serial console, refer to this page, an extended article about '''[[Using serial debug port to communicate]]'''. {| cellspacing="0" cellpadding="5" border="1" align="center" width="100%" style="text-align: left;"|-| bgcolor="#cccccc" |'''Audio'''|-|Connect an '''external output audio device''' to the 3.5mm jack Audio Out connector in IGEP0020, such as external stereo powered speakers.|} External Audio input devices, such as a powered microphone or the audio output of a PC or MP3 player, can be connected to the via a 3.5mm jack (Audio IN). {| cellspacing="0" cellpadding="5" border="1" align="center" width="100%" style="text-align: left;"|-| bgcolor="#cccccc" |'''Keyboard & Mouse'''|-| In IGEP0020 you might need a powered hub to connect to most USB.Connect an '''USB hub to the USB host connector''' in your IGEP0020, and then plug your keyboard and mouse into the USB hub. |} '''Only USB 2.0 devices will work''' in IGEP0020, so if you connect any USB mouse 1.0 into the USB host connector without using a USB hub 2.0, it will not work. {| cellspacing="0" cellpadding="5" border="1" align="center" width="100%" style="text-align: left;"|-| bgcolor="#cccccc" |'''Network'''|-| Plug an '''Ethernet cable''' between IGEP0020 and your client machine (or any other network device with ethernet connectivity).|} IGEP0020 comes with one 10/100BASE-TX Ethernet ports. In the following chapters we will use ethernet to access IGEP0020 with IP configuration, send files, etc. {| cellspacing="0" cellpadding="5" border="1" align="center" width="100%" style="text-align: left;"|-| bgcolor="#cccccc" |'''Power up'''|-| Once you have connected the peripherals '''you can apply power''' to your IGEP0020 (5V DCC).|} * '''Serial''': If you have connected the '''serial debug port''', you will see the system traces as the board is starting up. Finally you will see the boot prompt asking for login. (read the next chapter of this tutorial) * '''LED's''': You will also see a few LED's flash in IGEP0020 during the system boot(the sequence will be different based on software version). * '''Monitor''': Finally, if you connected the DVI-D signal (with HDMI connector) to a monitor, the desktop of the preinstalled software will appear on the screen and you will be able to use the mouse and the keyboard, if connected. * '''USB devices''': You will be able to use your keyboard and mouse and 'play' with some features of this little distribution. {| |-| [[Image:Poky-prompt-screenshot.png|thumb|550px|left|Poky prompt]] [[ImageCategory:Poky-screenshot.png|thumb|400px|right|Poky desktop]]|}<br style="clear:both" /> {{Navigation/IGEP Technology Devices Guides/Getting Started/Ending|device=IGEP0020}} [[Category:IGEP0020]][[Category:Tutorials]]