39
edits
Changes
From IGEP - ISEE Wiki
no edit summary
IGEPv2 RC version:
*Available only the first 28 pads IGEPv2 RG version: *Available all 30 pads
{| cellspacing="1" cellpadding="1" border="1" align="JUSTIFY" style="width: 900px; height: 1064px;"
| bgcolor="#CCCCCC" |GPIO_185(mode=4)<br>SAFE_MODE(mode=7)
| bgcolor="#CCCCCC" |TXS0102DCUR
|-
| 29
| GPMC_NCS7
| GPT8_PWM_EVT(mode=3)
| PWM signal
| GPMC_NCS7(mode=0)<br>GPMC_IO_DIR(mode=1)<br>MCBSP4_FSX(mode=2)<br>GPIO_58(mode=4)<br>SAFE_MODE(mode=7)
| -
|-
| bgcolor="#CCCCCC" |30
| bgcolor="#CCCCCC" |MCSPI1_CS3
| bgcolor="#CCCCCC" |MCSPI1_CS3(mode=0)
| bgcolor="#CCCCCC" |SPI1 Chip select 3
| bgcolor="#CCCCCC" |HSUSB2_TLL_DATA2(mode=2)<br>HSUSB2_DATA2(mode=3)<br>GPIO_177(mode=4)<br>MM2_TXDAT(mode=5)<br>SAFE_MODE(mode=7)
| bgcolor="#CCCCCC" |LBEP5CLWMC
|}
<br> TFP410: converts DVI signal to HDMI
TXS0102DCUR: Increse I2c3 voltage to 5V to read EDID information LBEP5CLWMC: Wifi and Bluetooth chip on IGEP0020-RG<br>
===== JA42 connector =====
JA42 is used for DVI (Digital Video Interface) control part, TouchScreen control and SPI1.
The current available on the DC_5V rail is limited to the available current that remains from the DC supply that is connected to the DC power jack on the board. Keep in mind that some of that power is needed by the USB Host power rail and if more power is needed for the expansion board, the main DC power supply current capability may need to be increased. All signals are 1.8V except the DVI_PUP which is a 3.3V signal. The 1.8V rail is for level translation only and should not be used to power circuitry on the board. The 3.3V rail also has limited capacity on the power as well. It is suggested that the 5V rail be used to generate the required voltages for an adapter card. *Note that <b>only IGEPv2 RG version</b> has all 22 pads available. Other boards have only first 20 pads available. <br>
{| cellspacing="1" cellpadding="1" border="1" align="JUSTIFY" style="width: 900px; height: 343px;"
| bgcolor="#CCCCCC" |-
|-
| 21
| GPMC_NCS7
| GPT8_PWM_EVT(mode=3)
| PWM signal
| GPMC_NCS7(mode=0)<br>GPMC_IO_DIR(mode=1)<br>MCBSP4_FSX(mode=2)<br>GPIO_58(mode=4)<br>SAFE_MODE(mode=7)
| -
|-
| bgcolor="#CCCCCC" |22
| bgcolor="#CCCCCC" |MCSPI1_CS3
| bgcolor="#CCCCCC" |MCSPI1_CS3(mode=0)
| bgcolor="#CCCCCC" |SPI1 Chip select 3
| bgcolor="#CCCCCC" |HSUSB2_TLL_DATA2(mode=2)<br>HSUSB2_DATA2(mode=3)<br>GPIO_177(mode=4)<br>MM2_TXDAT(mode=5)<br>SAFE_MODE(mode=7)
| bgcolor="#CCCCCC" |LBEP5CLWMC
|}
TFP410: converts DVI signal to HDMI LBEP5CLWMC: Wifi and Bluetooth chip on IGEP0020-RG<br>
<section end=IGEP0020 expansion connectors />
[[Category:IGEP Processor Boards]]
